AGFA Printer manual Engine is NOW Ready for a Long Stand Still

Page 24

:ANAPURNA L/XL

OPERATOR MANUAL

8.4. Long Stand Still

This procedure must be carried out:

-If the engine’s “Stand Still Time” is 1 week or longer…

-If the vacuum pressure is going to be closed down…

SHUTDOWN -- preparing the engine:

-Move the carriage to the Purge position.

-Flush cleaning solution through the heads:

-First purge the 4 right heads (Lc, Lm, W1, W2), close them,

and in the second stage, purge the remaining 4 left heads (K, C, M, Y).

-Finally, open the 4 right heads again, and purge all 8 heads together now. By doing so, you’ll have the most optimal cleaning pressure.

-Leave all ink valves in the “S” position, set the Solution valve to “I”.

-On the Engine’s Control Panel, perform a “Head Lift-Up”.

(the carriage will go to the highest position)

-Clean the Head Base Plate with a cloth

-Set the Vacuum Pressure to “0”. (Negative Pressure)

-Mount the “Capping Plate” underneath the Head Base Plate.

-use a plastic foil to wrap around the capping plate (new foil every time)

-place a support between the capping plate and the grid.

-bring down the carriage by turning manually, until it’s fixed.

(use some packing material as support)

-Push the emergency stop, and leave it pushed in! (restart-safety) Shut down the engine’s PC.

-Switch OFF the main power, by using the main-switch in the engine’s fuse box.

-Turn off the compressed air.

MAIN SWITCH

- THE ENGINE IS NOW READY FOR A LONG STAND STILL -

AB]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]24]8/09/2006]

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Anapurna L/XL Table of Contents Safety Instructions Printer Overview and Features System DimensionsFront view, parts & locations Rear view, parts & locations Cover Open Sensor Head Carriage view, parts Signal tower Head technology Color SequenceAnapurna UV Curable Ink General informationColor gamut PackingInk Circuit Main ink tanksAuto ink supply Sub Ink TankRead out How to make changes 2-Way valves Printing heads Ink supply by means of negative pressureEncoder Test can be found in the Test menu Ink Refill System what can go wrong… Waste TankCuring setup and sequences Settings in softwareLamp Type Cure Default, Set or Both UV Curing SystemBy default, Full power should be used whenever possible Uni- and Bi-directional printingPrinting Table Belt Tension controlMaintenance Replacement of Conveyor beltMaintenance Daily Maintenance Nozzle check/purgeLittle purge Cleaning the failing heads Weekly Maintenance Engine Storage AT the END of the WeekLong Stand Still Engine is NOW Ready for a Long Stand StillEngine is NOW Ready to Print Again Media Setup Roll to RollAuto Feed System Take-Up Motor Box Rigid Media Rigid Support tablesAB298/09/2006 Automatic Head Base Height Setup Head Base Height ControlMm Gap Anapurna Control Program Control Program MenuDisplay Printing Progress Set Top forward and Left MarginSetup Parameter Menu Good AB358/09/2006 AB368/09/2006 Test Menu To end this test, select Reset Test in the same menu, Carriage will move slowly back to the Home positionPrinting an image Preparing an imagePreparing the Anapurna Carriage must be moved to the home position firstPrinting the image Cancel a print While printing, press S and Y, the print is then cancelledPurge function on the printing Tips & Tricks Printing on heat sensitive mediaMedia corners lift a bit up rigid media Image size/border Wasatch Rip
Top Page Image Contents