Panasonic KX-FC231NZ, KX-FC235AL manual Display setup

Page 78

10. Programmable Features

6.Select “On” or “Off” (default), then press

{>}.

7.Press {ih}.

Note:

LWhen the night mode is turned ON, “[N]” is displayed.

LSet the receiving mode to TEL mode.

Setting the start and end time for night mode

1.Press {j/OK}.

2.Select “Handset Setup”, then press {>}.

3.Select “Ringer Setup”, then press {>}.

4.Select “Night Mode”, then press {>}.

5.Select “Start/End”, then press {>}.

6.Enter the desired hour and minute you wish to start this feature by selecting 2 digits for each.

L If you use 12-hour time entry, select “AM” or “PM” by pressing {*} repeatedly before entering the time.

7.Enter the desired hour and minute you wish to end this feature by selecting 2 digits for each.

L If you use 12-hour time entry, select “AM” or “PM” by pressing {*} repeatedly before entering the time.

8.Press {j/OK}.

9.Press {ih}.

Setting the ring delay for night mode

This setting allows the handset to ring during night mode if the caller waits long enough. After the selected delay time has passed, the handset will ring. If you select “No Ringing”, the handset will not ring during night mode.

1.Press {j/OK}.

2.Select “Handset Setup”, then press {>}.

3.Select “Ringer Setup”, then press {>}.

4.Select “Night Mode”, then press {>}.

5.Select “Ring Delay”, then press {>}.

6.Select “30 sec.”, then press {>}.

7.Press {ih}.

Note:

LWe recommend you select “30 sec.”. This is because the base unit detects an incoming call prior to handset.

Selecting categories to bypass night mode

1.Press {j/OK}.

2.Select “Handset Setup”, then press {>}.

3.Select “Ringer Setup”, then press {>}.

4.Select “Night Mode”, then press {>}.

5.Select “Select Category”, then press

{>}.

6.Press the desired category numbers, then press {j/OK}.

L The selected category number will flash. L To cancel a selected category number,

press the number again. The number will stop flashing.

7.Press {ih}.

10.5.5 Display setup

Selecting the standby mode display

“Base Number”: The current base unit number is displayed.

“Handset Number”: The current handset number is displayed.

“Off” (default): Only the current date and time are displayed.

1.Press {j/OK}.

2.Select “Handset Setup”, then press {>}.

3.Select “Display Setup”, then press {>}.

4.Select “Standby Display”, then press

{>}.

5.Select the desired setting, then press {>}.

6.Press {ih}.

Note:

L If “Base Number” is selected and the current base unit number is 2, “-2-”is displayed.

L If “Handset Number” is selected and the current handset number is 2, “[2]” is displayed.

Changing the display language

1.Press {j/OK}.

2.Select “Handset Setup”, then press {>}.

3.Select “Display Setup”, then press {>}.

4.Select “Select Language”, then press

{>}.

5.Select the desired language, then press {>}.

6.Press {ih}.

Note:

LIf you select a language you cannot read, press {ih}, {j/OK}, press {e} 2 times, press {>}, press {v} 2 times, press {>}, press {v}, press {>}, select the desired language, then press {>}. Press {ih}.

76

Page 77 Page 79
Image 78
Page 77 Page 79
Contents KX-FC231NZ How to use the operating instructions OpenHandset Location of ControlsBase unit Buttons Listed in alphabetical orderKX-FC231NZ Attach your sales receipt hereKX-FC235AL TrademarksFor Australian users For New Zealand usersImportant information for Australian users InstallationService difficulties Instructions to customerImportant safety instructions Battery For best performance Before calling back Phonebook103 101102 105For Australian users Included accessoriesQuantity For New Zealand usersFor Users in New Zealand General Warning Accessory informationAvailable accessories Important NoticeButton descriptions of the base unit Button descriptions of the handset Display descriptions of the handset Display iconsDisplay icon Meaning Overview Ink film installation / replacement Installing the ink filmCorrect IncorrectPaper tray Replacing the ink filmRecording paper CorrectIncorrectReplacing the batteries Battery installation / replacementInstalling the batteries Panasonic batteries. See page 11 forConnections Battery icons Battery strength Battery chargeBattery strength Battery lifePower OFF Turning the handset power ON/OFFPower on Base unit help functionINT Adjusting handset Adjusting base unit VolumeRinger volume Ring toneExample 315 PM 12-hour time entry Date and timeWith the handset Example 10 August, 2005 Press 10 08SET Menu Your logoWith the base unit Example 315PM 12-hour time entry 1. Press 03To enter your logo Example Bill To select characters using a or BKeypad Characters To change uppercase or lowercase lettersExample +64 9 Your fax numberYour FAX no Press SET To delete a numberMaking phone calls To turn key lock OFF, press j/OK for about 2 seconds MuteKey lock Digital SP-PHONE MuteAnswering phone calls INT. Any key answer featureAuto talk feature Handset phonebookMaking a phone call using the phonebook CategoriesEditing a stored item Erasing stored items One touch dialChain dial Base unit phonebook Erasing a stored itemErase Digital SP-PHONE Caller ID service How Caller ID is displayedAnother method to erase a stored item Category features for Caller ID subscribers Using Caller ID typeChanging category ring tones Viewing and calling back using caller information Caller IDFAX/START Digital SP-PHONE Editing a caller’s telephone number before calling back Erasing caller informationInto the base unit phonebook Storing caller information into the phonebookInto the handset phonebook To erase specific caller information Press Caller IDVoice mail service for Australian users only Call minder for New Zealand users onlyTurning SMS ON/OFF SMS Short Message ServiceUsing public mailbox and private mailboxes Changing SMS message centre numbersSending a message Writing and sending a new messageEditing a saved message Receiving a messageDisplaying / Sending a saved message Erasing saved messagesStoring the sender’s number in the handset phonebook Displaying a received messageErasing received messages Editing the sender’s number before calling backStoring the PBX line access number for PBX users only Guide to SMS settingsChanging private mailbox settings Creating private mailboxesCharacter entry modes How to enter charactersAvailable character entries for SMS LetterWise character table for EnglishFollowing are used for both uppercase and lowercase Sending a fax manually Stop Redial FAX/START Digital SP-PHONEDocuments you can send Programming items into the broadcast memory Sending a fax using the base unit phonebookBroadcast transmission Adding a new item into the broadcast memorySending the same document to pre-programmed parties To cancel broadcast transmissionErasing a stored item from the broadcast memory To send the same document to a one-time group of partiesUse only as a fax FAX only mode Selecting the way to use your fax machineAuto receive Use mostly as a telephone TEL mode How to receive phone calls and faxesManual receive Activating TEL mode Receiving a fax manually Auto answerStop FAX/START Digital SP-PHONE Ring setting in TAM/FAX mode Activating TAM/FAX modeTAM/FAX Mode Receiving a fax automatically Auto answer onActivating FAX only mode FAX only ModeTo display the junk fax prohibitor list Activating the junk fax prohibitorStoring undesired callers To print the junk fax prohibitor listUsing with the ring detection feature More copying features Making a copyStop Start A4, Letter Setting Recording Original Paper size Document SizeDefault LegalSET MIC Stop Erase GREETING/REC GREETING/CHECK Recording your greeting messageErasing your recorded greeting message Press GREETING/RECErasing recorded messages Listening to recorded messagesLeaving a message for others or yourself SET Stop Erase PlaybackFor voice mail/Call minder service subscribers Remote operation using remote commands Operating from a remote locationSummary of remote operation Skip greeting message Turn OFF auto answer settingTo turn on the auto answer setting Recording a marker messageProgramming basic features Programming advanced featuresBase unit programming Basic features Advanced features Code #44 Setting the memory reception alert Code #42 Setting the message alertCode #43 Setting the recording time alert Code #46 Setting friendly receptionCode #68 Setting the Error Correction Mode ECM Code #58 Setting the scan contrastCode #67 Setting the incoming message monitor Code #76 Setting the connecting toneDirect commands for programming features Program code and direct command button#36 Receiving reduction 72% 86% OFF #76 Connecting tone#80 Set default YES #39 Display contrastHandset programming Programmable Features Programmable functions AlarmNight mode Ringer optionsDisplay setup Call options Other optionsProgrammable functions using the base unit PIN Setting pause lengthChanging the recall time Setting call restriction Storing/changing emergency numbersSelecting area codes to be deleted automatically Resetting handset programming that uses the base unit PIN Changing the base unit PIN personal identification numberOperating additional units Registering a handset to a base unitHandset locator Cancelling a handsetCancelling a base unit Increasing the range of the base unitIntercom between handsets Example When handset 1 calls handset HandsetExample When handset 1 transfers a call to handset Handset Transferring calls between handsets / Conference callsCopying handset phonebook items Copying a stored itemCopying all stored items Available character entries for the handset LetterWise character table for English KX-FC235AL onlyAlphabet character table ABC Numeric entry table Greek character table M Extended 1 character table N Extended 2 character table OCyrillic character table P Error messages Reports Error messages Base unit display Display Cause and SolutionTransmission error occurred. Try again Service personnelPlease use genuine Panasonic replacement film Unnecessary messagesWhen a function does not work, check here Initial settingsGeneral Problem Cause & Solution Handset does not Problem Cause & Solution Speakerphone is notReturns to standby mode Charging but the batteryIs pressed Problem Cause & SolutionDocuments using Static, sound cuts in/outFax sending Fax receivingDocuments automatically Receiving modeWhen an extension Display showsCopying Answering machineSMS KX-FC235AL only If a power failure occurs When the recording paper has jammed in the unit Recording paper jamsCorrect When the recording paper was not fed into the unit properly START1Document jams sending Document feeder / scanner glass cleaning Do not use paper products, such as paper towels or tissuesThermal head cleaning 104 Reference lists and reports Base unit only Specifications Mass Weight Approx g Duplex procedureRF transmission power Approx mW Operating environment StandardIndex 109 110 111 Manufacturer Panasonic Communications Malaysia Sdn. Bhd Sales Department Panasonic Australia Pty. LimitedPanasonic New Zealand Limited Global web site Copyright PFQX2248ZA CM0605DT0
Top Page Image Contents