Airlink CDMA/1x manual 108

Page 114

Modem has not registered: This can be a transitory state. Wait 30 to 60 seconds and attempt the command again.

Modem is registering: Generally, this indicates the Raven is attempting to contact Verizon’syour cellular provider’s network. Wait 30 to 60 seconds and attempt again.

Modem has registered: When you see this message, the Raven is regis- tered on Verizon’s network . Continue on to the next step. .

FIGURE 4. Pass Thru Mode: Modem Status

5.Type AT+GMR and press Enter. You should get a long output response. Near the end of the output, will be the current five-digit PRL version.

FIGURE 5. Pass Thru Mode: +GMR example

6.Issue AT+CDV*22899 and Press Enter. You should get “OK” as a response. Wait 2 to 3 minutes for the PRL to download and install.

7.Enter AT+GMR again to verify the PRL version change.

108	Raven CDMA User Guide for Verizon, version 2.23

Image 114

Contents User Guide Raven Cdma User Guide for Verizon, version Contents AT Mode PassThru Mode PPP Mode Slip Mode UDP Pad Mode DNS Using Names Instead of IP addressesConfiguring Keepalive Data usage using Keepalive TCP PAD ModeConnecting the Antenna Connecting power Appendix 1 Specifications for the Raven CdmaRaven Snmp Configuration Snmp OverviewWhat is RSSI? Why is the Rssi for my Raven negative? Appendix 4 Example of the MIB trapSupport web site Contacting Technical Support Introduction to Raven Cdma Cdma Overview Establishing a Internet ConnectionUsing Cdma to Communicate with Your Equipment Common Uses for the Raven Financial Point of Sale and KioskBackup connection to the Internet Connecting the Raven to your computer Quick Start Guide and Setup WizardActivation of the Raven Setup Wizard Activating the Raven using AT Commands Raven Indicator LightsRaven Cdma User Guide for Verizon, version Utilities for the Raven AirLink Configuration Executive ACE Wireless ACE 3GAceNet AceViewAceView About Modem Modem Doctor IP Manager Dynamic Name Resolution Fully Qualified Domain NameConfiguring the Raven for Dynamic IP Wireless ACE Dynamic IP IP Manager configuration Restrictions for Modem NameDNS Using Names Instead of IP addresses Configuring DNSPPP-Peer Configuring Keepalive KeepaliveData usage using Keepalive Wireless ACE Keepalive ConfigurationHost Modes AT Mode PassThru Mode PPP Mode Slip ModeATDT10.0.0.1CR ATDT10001CR ATD#19788CR UDP Pad Mode UDP Auto AnswerReliable UDP TCP PAD Mode Multicast UDPHybrid Modes TCP Auto AnswerHybrid Mode Settings Modbus/BSAP Configuration Modbus OverviewSupervisory Control and Data Acquisition Scada TelemetryRemote Terminal Unit RTU Programmable Logic Controller PLCModbus TCP/IP Raven Modbus on UDPConfiguring the Raven at the Polling Host for Modbus on UDP Default Power-up ModePort IDs to IPs Dynamic IPConfiguring the Remote Ravens for Modbus with Wireless ACE Modem Name and DomainHost Raven IP Dynamic IPsRTU settings Raven mounted in an enclosure with an RTURTU to Raven setup Simple Network Management Protocol Snmp Snmp OverviewSnmp Traps Raven Snmp ConfigurationManagement Information Base MIB Listening PortUser Name and Password Security LevelWireless ACE Changing the Raven Password Menu Option Trap Destination Hardware Installation Connecting the AntennaConnecting power Connecting the Raven to a computer or other deviceData Services & RF Features Cdma Specifications for the Raven CdmaPhysical Characteristics EnvironmentalPower Management Power consumptionSerial Port Pin-outs Raven Cdma User Guide for Verizon, version Mounting Kit Raven Mounting Bracket, part number 100-170-1009 aRaven Cdma User Guide for Verizon, version AT Commands Using Wireless AceUsing Telnet Terminal Emulation Wireless ACE Using AT CommandsStartAll ProgramsAccessoriesCommunicationsHyperTerminal HyperTerminal AT mode via Telnet Direct Serial ConnectionAT Command Tables HyperTerminal Comport SettingInformation Commands Command Details Information and StatusRaven Basic Commands Basic Commands common AT commandsNone Activation Activation Provisioning Cellular Network Cellular Network Verizon’s CdmaLocal Network and Host Modes PassThruThis command is not pro Ceeded by AT Local Network and Host ModesDatabits = 7 or Itystop bits Parity = S23=speed,databits Speed =Paritystop bits Stopbits =Figured to ignore DTR. When Ignore DTR is enabled Slip Default Atdt N.n = subnetPPP Direct Communication When *CSX1=0 TelnetDirect Communication S53=methodd.d.d.d Method = PppppPort Yyyy,hhmmss Time and DateMm/dd/yyyy = Hhmmss =Fn=d.d.d.d Friends ModeFriends Mode DNSn=d.d.d.dKeepalive IP Manager If *DOMAIN=eairlink.com, then whenExample if *MODEMNAME=mymodem Raven Cdma User Guide for Verizon, version Logging ModbusMLISTid=d.d.d.d Modbus SettingsCannot be configured in Wireless ACE D.d=IP orLow order 4 bits Snmp Simple Network Management Protocol D.d = IP orSMTP/SMS Number Smtp email and SMS messagingNumber= SMS Name=Flag=1 Index=0-9C3211 Flag=0 Flag=2Other Other Settings Example of the MIB trap AIRLINK-MIB Definitions = Begin ImportsRaven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version END Raven Cdma User Guide for Verizon, version Frequently Asked Questions FAQ and Solutions What is RSSI? Why is the Rssi for my Raven negative?Dual-band What is the Proper RF Coverage for my Raven?What Type of Antenna is Best for my Raven? DipoleWhat do I need to power my Raven ? Can I use a portable battery to power my Raven ?Mounts 103 Public Mode *HOSTPRIVMODE=0 Private Mode *HOSTPRIVMODE=1What is the COM1000? 105Wireless ACE Wireless ACE Update PRLWireless ACE Update PRL interface AT Commands108 Support web site Contacting Technical Support