Airlink CDMA/1x manual Data usage using Keepalive, Wireless ACE Keepalive Configuration

Page 28

Keepalive

To set the Keepalive using Wireless ACE, select Other from the menu on the left.

FIGURE 1. Wireless ACE: Keepalive Configuration

*IPPING sets the interval, in minutes, you want Keepalive to test the network connection. To disable Keepalive, set *IPPING to 0 (default setting).

Note: 15 minutes is the minimum time which can be set for Kee- palive.

*IPPINGADDR sets the IP address you want to use for the test. If *PPIN- GADDR is left blank or is set to an invalid IP address (i.e. an IP which is unreachable or one which is not a valid IP address), the modem will reset itself on a regular interval.

Data usage using Keepalive

When using Keepalive, be aware that a ping moves approximately 66 bytes of data over the network and is billable by the carrier. The following *IPPING settings will incur approximate monthly data usage in addition to any other data usage:

15 minutes	400k / month
30 minutes	200k / month
60 minutes	100k / month
120 minutes	50k / month

22	Raven CDMA User Guide for Verizon, version 2.23

Image 28

Contents User Guide Raven Cdma User Guide for Verizon, version Contents DNS Using Names Instead of IP addresses Configuring Keepalive Data usage using KeepaliveAT Mode PassThru Mode PPP Mode Slip Mode UDP Pad Mode TCP PAD ModeAppendix 1 Specifications for the Raven Cdma Raven Snmp ConfigurationConnecting the Antenna Connecting power Snmp OverviewAppendix 4 Example of the MIB trap What is RSSI? Why is the Rssi for my Raven negative?Support web site Contacting Technical Support Introduction to Raven Cdma Cdma Overview Establishing a Internet ConnectionUsing Cdma to Communicate with Your Equipment Common Uses for the Raven Financial Point of Sale and KioskBackup connection to the Internet Quick Start Guide and Setup Wizard Connecting the Raven to your computerActivation of the Raven Setup Wizard Activating the Raven using AT Commands Raven Indicator LightsRaven Cdma User Guide for Verizon, version Utilities for the Raven AirLink Configuration Executive ACE Wireless ACE 3GAceNet AceViewAceView About Modem Modem Doctor IP Manager Dynamic Name Resolution Fully Qualified Domain NameConfiguring the Raven for Dynamic IP Wireless ACE Dynamic IP IP Manager configuration Restrictions for Modem NameDNS Using Names Instead of IP addresses Configuring DNSPPP-Peer Configuring Keepalive KeepaliveData usage using Keepalive Wireless ACE Keepalive ConfigurationHost Modes AT Mode PassThru Mode Slip Mode PPP ModeATDT10.0.0.1CR ATDT10001CR ATD#19788CR UDP Pad Mode UDP Auto AnswerReliable UDP TCP PAD Mode Multicast UDPHybrid Modes TCP Auto AnswerHybrid Mode Settings Modbus/BSAP Configuration Modbus OverviewTelemetry Remote Terminal Unit RTUSupervisory Control and Data Acquisition Scada Programmable Logic Controller PLCModbus TCP/IP Raven Modbus on UDPDefault Power-up Mode Configuring the Raven at the Polling Host for Modbus on UDPPort IDs to IPs Dynamic IPConfiguring the Remote Ravens for Modbus with Wireless ACE Modem Name and DomainHost Raven IP Dynamic IPsRTU settings Raven mounted in an enclosure with an RTURTU to Raven setup Simple Network Management Protocol Snmp Snmp OverviewRaven Snmp Configuration Management Information Base MIBSnmp Traps Listening PortUser Name and Password Security LevelWireless ACE Changing the Raven Password Menu Option Trap Destination Hardware Installation Connecting the AntennaConnecting power Connecting the Raven to a computer or other deviceSpecifications for the Raven Cdma Physical CharacteristicsData Services & RF Features Cdma EnvironmentalPower consumption Power ManagementSerial Port Pin-outs Raven Cdma User Guide for Verizon, version Mounting Kit Raven Mounting Bracket, part number 100-170-1009 aRaven Cdma User Guide for Verizon, version AT Commands Using Wireless AceUsing Telnet Terminal Emulation Wireless ACE Using AT CommandsStartAll ProgramsAccessoriesCommunicationsHyperTerminal HyperTerminal AT mode via Telnet Direct Serial ConnectionAT Command Tables HyperTerminal Comport SettingInformation Commands Command Details Information and StatusRaven Basic Commands common AT commands Basic CommandsNone Activation Activation Provisioning Cellular Network Cellular Network Verizon’s CdmaLocal Network and Host Modes PassThruThis command is not pro Ceeded by AT Local Network and Host ModesS23=speed,databits Speed = Paritystop bitsDatabits = 7 or Itystop bits Parity = Stopbits =Figured to ignore DTR. When Ignore DTR is enabled Slip Default Atdt N.n = subnetPPP Direct Communication When *CSX1=0 TelnetDirect Communication Ppppp S53=methodd.d.d.d Method =Port Time and Date Mm/dd/yyyy =Yyyy,hhmmss Hhmmss =Friends Mode Friends ModeFn=d.d.d.d DNSn=d.d.d.dKeepalive IP Manager If *DOMAIN=eairlink.com, then whenExample if *MODEMNAME=mymodem Raven Cdma User Guide for Verizon, version Logging ModbusModbus Settings Cannot be configured in Wireless ACEMLISTid=d.d.d.d D.d=IP orLow order 4 bits Snmp Simple Network Management Protocol D.d = IP orSMTP/SMS Smtp email and SMS messaging Number= SMSNumber Name=Index=0-9 C3211 Flag=0Flag=1 Flag=2Other Other Settings Example of the MIB trap AIRLINK-MIB Definitions = Begin ImportsRaven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version END Raven Cdma User Guide for Verizon, version Frequently Asked Questions FAQ and Solutions What is RSSI? Why is the Rssi for my Raven negative?What is the Proper RF Coverage for my Raven? What Type of Antenna is Best for my Raven?Dual-band DipoleCan I use a portable battery to power my Raven ? What do I need to power my Raven ?Mounts 103 Public Mode *HOSTPRIVMODE=0 Private Mode *HOSTPRIVMODE=1What is the COM1000? 105Wireless ACE Wireless ACE Update PRLWireless ACE Update PRL interface AT Commands108 Support web site Contacting Technical Support