Airlink CDMA/1x manual Direct Communication

Page 80

TABLE 8. Direct Communication

Command

Parameters

Details

 

 

 

D[method][d.d.d.d][/ppppp]

method = P, T, N

Dial a connection to a remote IP and Port using method.

or

d.d.d.d = IP

P - Establish a UDP connection

 

D[method][@name][/ppppp]

address to con-

T - Establish a TCP connection

tact

N - Establish a Telnet connection

 

 

name = domain

 

ATD - Dial (establish) default connection.

 

name to contact

 

ATDP192.168.13.31/2332 - Dial (establish) UDP ses-

 

ppppp = IP port

 

sion to 192.168.13.31, at port 2332.

 

to contact

 

To end the connection, issue the +++ escape sequence or

 

 

 

 

drop the DTR line (if Ignore DTR S211=0 or &D2).

 

 

 

D continued

see above

The defualt connetion is set in S53.

 

 

If a domain name is specified, the '@' symbol can be

 

 

used to explicitly indicate the start of the name. For

 

 

example, if ATDPHONY is issued, this will be inter-

 

 

preted as dial a UDP connection to "HONY". To dial

 

 

using the default method to host "PHONY", one would

 

 

issue ATD@PHONY. .

 

 

If the method, IP address, or port is omitted, the values

 

 

from S53 are used. If a telnet connection is requested (N)

 

 

and the port is not supplied, port 23 will be used instead

 

 

of the value from S53.

 

 

Several special dialing numbers exist to make it easy to

 

 

establish a PPP or SLIP connection with the modem.

 

 

ATD#19788 or ATDT#19788 will establish a PPP con-

 

 

nection (see \APPP) and ATDT#7547 will establish a

 

 

SLIP connection (see \ASLIP).

 

 

Note: The source port of the session is the Device Port

 

 

(set by S110 or *DPORT).

 

 

 

PINGd.d.d.d[,n]

d.d.d.d = IP

Ping the specified IP address.

or

address to con-

Sends a single ping, returns either OK or ERROR

tact

PING domain_name[,n]

depending on result. Times out in 10 seconds. If n is pro-

n = amount of

vided, it specifies the amount of data to send with the

 

 

data to send

ping. If n is not provided, the default, 50 bytes is used.

 

 

 

74

Raven CDMA User Guide for Verizon, version 2.23

Image 80
Contents User Guide Raven Cdma User Guide for Verizon, version Contents DNS Using Names Instead of IP addresses Configuring Keepalive Data usage using KeepaliveAT Mode PassThru Mode PPP Mode Slip Mode UDP Pad Mode TCP PAD ModeAppendix 1 Specifications for the Raven Cdma Raven Snmp ConfigurationConnecting the Antenna Connecting power Snmp OverviewSupport web site Contacting Technical Support What is RSSI? Why is the Rssi for my Raven negative?Appendix 4 Example of the MIB trap Introduction to Raven Cdma Cdma Overview Establishing a Internet ConnectionUsing Cdma to Communicate with Your Equipment Common Uses for the Raven Financial Point of Sale and KioskBackup connection to the Internet Activation of the Raven Connecting the Raven to your computerQuick Start Guide and Setup Wizard Setup Wizard Activating the Raven using AT Commands Raven Indicator LightsRaven Cdma User Guide for Verizon, version Utilities for the Raven AirLink Configuration Executive ACE Wireless ACE 3GAceNet AceViewAceView About Modem Modem Doctor IP Manager Dynamic Name Resolution Fully Qualified Domain NameConfiguring the Raven for Dynamic IP Wireless ACE Dynamic IP IP Manager configuration Restrictions for Modem NameDNS Using Names Instead of IP addresses Configuring DNSPPP-Peer Configuring Keepalive KeepaliveData usage using Keepalive Wireless ACE Keepalive ConfigurationHost Modes AT Mode PassThru Mode ATDT10.0.0.1CR ATDT10001CR ATD#19788CR PPP ModeSlip Mode UDP Pad Mode UDP Auto AnswerReliable UDP TCP PAD Mode Multicast UDPHybrid Modes TCP Auto AnswerHybrid Mode Settings Modbus/BSAP Configuration Modbus OverviewTelemetry Remote Terminal Unit RTUSupervisory Control and Data Acquisition Scada Programmable Logic Controller PLCModbus TCP/IP Raven Modbus on UDPPort Configuring the Raven at the Polling Host for Modbus on UDPDefault Power-up Mode IDs to IPs Dynamic IPConfiguring the Remote Ravens for Modbus with Wireless ACE Modem Name and DomainHost Raven IP Dynamic IPsRTU settings Raven mounted in an enclosure with an RTURTU to Raven setup Simple Network Management Protocol Snmp Snmp OverviewRaven Snmp Configuration Management Information Base MIBSnmp Traps Listening PortUser Name and Password Security LevelWireless ACE Changing the Raven Password Menu Option Trap Destination Hardware Installation Connecting the AntennaConnecting power Connecting the Raven to a computer or other deviceSpecifications for the Raven Cdma Physical CharacteristicsData Services & RF Features Cdma EnvironmentalSerial Port Pin-outs Power ManagementPower consumption Raven Cdma User Guide for Verizon, version Mounting Kit Raven Mounting Bracket, part number 100-170-1009 aRaven Cdma User Guide for Verizon, version AT Commands Using Wireless AceUsing Telnet Terminal Emulation Wireless ACE Using AT CommandsStartAll ProgramsAccessoriesCommunicationsHyperTerminal HyperTerminal AT mode via Telnet Direct Serial ConnectionAT Command Tables HyperTerminal Comport SettingInformation Commands Command Details Information and StatusRaven None Basic CommandsBasic Commands common AT commands Activation Activation Provisioning Cellular Network Cellular Network Verizon’s CdmaLocal Network and Host Modes PassThruThis command is not pro Ceeded by AT Local Network and Host ModesS23=speed,databits Speed = Paritystop bitsDatabits = 7 or Itystop bits Parity = Stopbits =Figured to ignore DTR. When Ignore DTR is enabled Slip Default Atdt N.n = subnetPPP Direct Communication When *CSX1=0 TelnetDirect Communication Port S53=methodd.d.d.d Method =Ppppp Time and Date Mm/dd/yyyy =Yyyy,hhmmss Hhmmss =Friends Mode Friends ModeFn=d.d.d.d DNSn=d.d.d.dKeepalive IP Manager If *DOMAIN=eairlink.com, then whenExample if *MODEMNAME=mymodem Raven Cdma User Guide for Verizon, version Logging ModbusModbus Settings Cannot be configured in Wireless ACEMLISTid=d.d.d.d D.d=IP orLow order 4 bits Snmp Simple Network Management Protocol D.d = IP orSMTP/SMS Smtp email and SMS messaging Number= SMSNumber Name=Index=0-9 C3211 Flag=0Flag=1 Flag=2Other Other Settings Example of the MIB trap AIRLINK-MIB Definitions = Begin ImportsRaven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version END Raven Cdma User Guide for Verizon, version Frequently Asked Questions FAQ and Solutions What is RSSI? Why is the Rssi for my Raven negative?What is the Proper RF Coverage for my Raven? What Type of Antenna is Best for my Raven?Dual-band DipoleMounts What do I need to power my Raven ?Can I use a portable battery to power my Raven ? 103 Public Mode *HOSTPRIVMODE=0 Private Mode *HOSTPRIVMODE=1What is the COM1000? 105Wireless ACE Wireless ACE Update PRLWireless ACE Update PRL interface AT Commands108 Support web site Contacting Technical Support