Airlink CDMA/1x manual IP Manager, If *DOMAIN=eairlink.com, then when

Page 85

TABLE 13. Keepalive

Command

Parameters

Details

 

 

 

*MINXMIT=n

n=seconds

Minimum transmit period enforcement. When set to n

 

 

seconds, will not let the *IPPING, *PPMINTIME, and

 

 

the *MSCIUPDPERIOD timers to be set less than n sec-

 

 

onds.

 

 

Note that the *PPTIME can still be set to less than

 

 

*MINXMIT, but the packets will still be transmitted no

 

 

more often than the *PPMINTIME.

 

 

Warning: The *MINXMIT value is can only be set one

 

 

time and AirLink must be contacted to reset it.

 

 

 

IP Manager

IP Manager (page 15) is a service from AirLink which allows a Raven with a dynamic IP to be contacted as if it had a static IP by using a Fully Qualified Domain Name.

TABLE 14. IP Manager

Command

Parameters

Details

 

 

 

*DOMAIN=[name]

name = domain

Domain (or domain zone) of which the Raven is a part.

 

name (i.e. eair-

This value is used during name resolutions if a fully

 

link.com)

qualified name is not provided and also for DNS

 

 

updates. This value can be up to 20 characters long.

 

 

If *DOMAIN=eairlink.com, then when

 

 

ATDT@remote1 is entered, the fully qualified name

 

 

remote1.eairlink.com will be used to perform a DNS

 

 

query to resolve the name to an IP address.

 

 

Note: Only letters, numbers, hyphens, and periods can

 

 

be used.

 

 

 

*IPMANAGERn=[name]

n= 1 or 2

Sets a domain name or IP address to send IP change noti-

 

name = domain

fications to. Up to two independent IP Manager servers

 

can be set, using either AT*IPMANAGER1 or

 

name

 

AT*IPMANAGER2. Updates to a server can be disabled

 

 

 

 

by setting that entry to nothing (i.e.

 

 

"AT*IPMANAGER1=").

 

 

 

Raven CDMA User Guide for Verizon, version 2.23

79

Image 85
Contents User Guide Raven Cdma User Guide for Verizon, version Contents Configuring Keepalive Data usage using Keepalive DNS Using Names Instead of IP addressesAT Mode PassThru Mode PPP Mode Slip Mode UDP Pad Mode TCP PAD ModeRaven Snmp Configuration Appendix 1 Specifications for the Raven CdmaConnecting the Antenna Connecting power Snmp OverviewAppendix 4 Example of the MIB trap What is RSSI? Why is the Rssi for my Raven negative?Support web site Contacting Technical Support Introduction to Raven Cdma Establishing a Internet Connection Cdma OverviewUsing Cdma to Communicate with Your Equipment Financial Point of Sale and Kiosk Common Uses for the RavenBackup connection to the Internet Quick Start Guide and Setup Wizard Connecting the Raven to your computerActivation of the Raven Setup Wizard Raven Indicator Lights Activating the Raven using AT CommandsRaven Cdma User Guide for Verizon, version Utilities for the Raven Wireless ACE 3G AirLink Configuration Executive ACEAceView AceNetAceView About Modem Modem Doctor IP Manager Fully Qualified Domain Name Dynamic Name ResolutionConfiguring the Raven for Dynamic IP Restrictions for Modem Name Wireless ACE Dynamic IP IP Manager configurationConfiguring DNS DNS Using Names Instead of IP addressesPPP-Peer Keepalive Configuring KeepaliveWireless ACE Keepalive Configuration Data usage using KeepaliveHost Modes AT Mode PassThru Mode Slip Mode PPP ModeATDT10.0.0.1CR ATDT10001CR ATD#19788CR UDP Auto Answer UDP Pad ModeReliable UDP Multicast UDP TCP PAD ModeTCP Auto Answer Hybrid ModesHybrid Mode Settings Modbus Overview Modbus/BSAP ConfigurationRemote Terminal Unit RTU TelemetrySupervisory Control and Data Acquisition Scada Programmable Logic Controller PLCRaven Modbus on UDP Modbus TCP/IPDefault Power-up Mode Configuring the Raven at the Polling Host for Modbus on UDPPort Dynamic IP IDs to IPsWireless ACE Modem Name and Domain Configuring the Remote Ravens for Modbus withDynamic IPs Host Raven IPRaven mounted in an enclosure with an RTU RTU settingsRTU to Raven setup Snmp Overview Simple Network Management Protocol SnmpManagement Information Base MIB Raven Snmp ConfigurationSnmp Traps Listening PortSecurity Level User Name and PasswordWireless ACE Changing the Raven Password Menu Option Trap Destination Connecting the Antenna Hardware InstallationConnecting the Raven to a computer or other device Connecting powerPhysical Characteristics Specifications for the Raven CdmaData Services & RF Features Cdma EnvironmentalPower consumption Power ManagementSerial Port Pin-outs Raven Cdma User Guide for Verizon, version Raven Mounting Bracket, part number 100-170-1009 a Mounting KitRaven Cdma User Guide for Verizon, version Using Wireless Ace AT CommandsWireless ACE Using AT Commands Using Telnet Terminal EmulationStartAll ProgramsAccessoriesCommunicationsHyperTerminal Direct Serial Connection HyperTerminal AT mode via TelnetHyperTerminal Comport Setting AT Command TablesInformation Commands Information and Status Command DetailsRaven Basic Commands common AT commands Basic CommandsNone Activation Activation Provisioning Cellular Network Verizon’s Cdma Cellular NetworkPassThru Local Network and Host ModesLocal Network and Host Modes This command is not pro Ceeded by ATParitystop bits S23=speed,databits Speed =Databits = 7 or Itystop bits Parity = Stopbits =Figured to ignore DTR. When Ignore DTR is enabled Slip Default N.n = subnet AtdtPPP Direct Communication Telnet When *CSX1=0Direct Communication Ppppp S53=methodd.d.d.d Method =Port Mm/dd/yyyy = Time and DateYyyy,hhmmss Hhmmss =Friends Mode Friends ModeFn=d.d.d.d DNSn=d.d.d.dKeepalive If *DOMAIN=eairlink.com, then when IP ManagerExample if *MODEMNAME=mymodem Raven Cdma User Guide for Verizon, version Modbus LoggingCannot be configured in Wireless ACE Modbus SettingsMLISTid=d.d.d.d D.d=IP orLow order 4 bits D.d = IP or Snmp Simple Network Management ProtocolSMTP/SMS Number= SMS Smtp email and SMS messagingNumber Name=C3211 Flag=0 Index=0-9Flag=1 Flag=2Other Other Settings AIRLINK-MIB Definitions = Begin Imports Example of the MIB trapRaven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version END Raven Cdma User Guide for Verizon, version What is RSSI? Why is the Rssi for my Raven negative? Frequently Asked Questions FAQ and SolutionsWhat Type of Antenna is Best for my Raven? What is the Proper RF Coverage for my Raven?Dual-band DipoleCan I use a portable battery to power my Raven ? What do I need to power my Raven ?Mounts 103 Private Mode *HOSTPRIVMODE=1 Public Mode *HOSTPRIVMODE=0105 What is the COM1000?Wireless ACE Update PRL Wireless ACEAT Commands Wireless ACE Update PRL interface108 Contacting Technical Support Support web site