Airlink CDMA/1x manual Activating the Raven using AT Commands, Raven Indicator Lights

Page 14

Activation of the Raven CDMA

Activating the Raven using AT Commands

An alternate method to configure and activate your Raven is by AT commands (full listing beginning on page 53) sent directly to the modem via a terminal application. This method is recommended only in situations where the Setup Wizard is not available and/or the configuration for the Raven is unusual.

Caution: While you can configure your Raven using Wireless ACE (page 10) or AceNet (page 11), it is not recommended to activate the Raven using either Wireless ACE or AceNet.

Raven Indicator Lights

When your Raven is connected to power and an antenna, there is a specific pattern to the lights to indicate its operation mode.

FIGURE 2. Raven indicator lights

Tx (transmit) and Rx (receive) - Lights will flash as data is transferred to and from the Raven on the remote network.

RSSI - Light shows the strength of the signal and may be nearly solid (strong signal) or flashing (weaker signal). A slow flash indicates a very weak signal.

Reg - Indicates the Raven has acquired an IP from Verizon. Chan - Indicates the modem has acquired a network channel. Link - Indicate a successful connection to the cellular network.

8	Raven CDMA User Guide for Verizon, version 2.23

Image 14

Contents User Guide Raven Cdma User Guide for Verizon, version Contents AT Mode PassThru Mode PPP Mode Slip Mode UDP Pad Mode DNS Using Names Instead of IP addressesConfiguring Keepalive Data usage using Keepalive TCP PAD ModeConnecting the Antenna Connecting power Appendix 1 Specifications for the Raven CdmaRaven Snmp Configuration Snmp OverviewSupport web site Contacting Technical Support What is RSSI? Why is the Rssi for my Raven negative?Appendix 4 Example of the MIB trap Introduction to Raven Cdma Cdma Overview Establishing a Internet ConnectionUsing Cdma to Communicate with Your Equipment Common Uses for the Raven Financial Point of Sale and Kiosk Backup connection to the Internet Activation of the Raven Connecting the Raven to your computerQuick Start Guide and Setup Wizard Setup Wizard Activating the Raven using AT Commands Raven Indicator LightsRaven Cdma User Guide for Verizon, version Utilities for the Raven AirLink Configuration Executive ACE Wireless ACE 3GAceNet AceViewAceView About Modem Modem Doctor IP Manager Dynamic Name Resolution Fully Qualified Domain NameConfiguring the Raven for Dynamic IP Wireless ACE Dynamic IP IP Manager configuration Restrictions for Modem NameDNS Using Names Instead of IP addresses Configuring DNSPPP-Peer Configuring Keepalive KeepaliveData usage using Keepalive Wireless ACE Keepalive ConfigurationHost Modes AT Mode PassThru Mode ATDT10.0.0.1CR ATDT10001CR ATD#19788CR PPP ModeSlip Mode UDP Pad Mode UDP Auto AnswerReliable UDP TCP PAD Mode Multicast UDPHybrid Modes TCP Auto AnswerHybrid Mode Settings Modbus/BSAP Configuration Modbus OverviewSupervisory Control and Data Acquisition Scada TelemetryRemote Terminal Unit RTU Programmable Logic Controller PLCModbus TCP/IP Raven Modbus on UDPPort Configuring the Raven at the Polling Host for Modbus on UDPDefault Power-up Mode IDs to IPs Dynamic IPConfiguring the Remote Ravens for Modbus with Wireless ACE Modem Name and DomainHost Raven IP Dynamic IPsRTU settings Raven mounted in an enclosure with an RTURTU to Raven setup Simple Network Management Protocol Snmp Snmp OverviewSnmp Traps Raven Snmp ConfigurationManagement Information Base MIB Listening PortUser Name and Password Security LevelWireless ACE Changing the Raven Password Menu Option Trap Destination Hardware Installation Connecting the AntennaConnecting power Connecting the Raven to a computer or other deviceData Services & RF Features Cdma Specifications for the Raven CdmaPhysical Characteristics EnvironmentalSerial Port Pin-outs Power ManagementPower consumption Raven Cdma User Guide for Verizon, version Mounting Kit Raven Mounting Bracket, part number 100-170-1009 aRaven Cdma User Guide for Verizon, version AT Commands Using Wireless AceUsing Telnet Terminal Emulation Wireless ACE Using AT CommandsStartAll ProgramsAccessoriesCommunicationsHyperTerminal HyperTerminal AT mode via Telnet Direct Serial ConnectionAT Command Tables HyperTerminal Comport SettingInformation Commands Command Details Information and StatusRaven None Basic CommandsBasic Commands common AT commands Activation Activation Provisioning Cellular Network Cellular Network Verizon’s CdmaLocal Network and Host Modes PassThruThis command is not pro Ceeded by AT Local Network and Host ModesDatabits = 7 or Itystop bits Parity = S23=speed,databits Speed =Paritystop bits Stopbits =Figured to ignore DTR. When Ignore DTR is enabled Slip Default Atdt N.n = subnetPPP Direct Communication When *CSX1=0 TelnetDirect Communication Port S53=methodd.d.d.d Method =Ppppp Yyyy,hhmmss Time and DateMm/dd/yyyy = Hhmmss =Fn=d.d.d.d Friends ModeFriends Mode DNSn=d.d.d.dKeepalive IP Manager If *DOMAIN=eairlink.com, then whenExample if *MODEMNAME=mymodem Raven Cdma User Guide for Verizon, version Logging ModbusMLISTid=d.d.d.d Modbus SettingsCannot be configured in Wireless ACE D.d=IP orLow order 4 bits Snmp Simple Network Management Protocol D.d = IP orSMTP/SMS Number Smtp email and SMS messagingNumber= SMS Name=Flag=1 Index=0-9C3211 Flag=0 Flag=2Other Other Settings Example of the MIB trap AIRLINK-MIB Definitions = Begin ImportsRaven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version END Raven Cdma User Guide for Verizon, version Frequently Asked Questions FAQ and Solutions What is RSSI? Why is the Rssi for my Raven negative?Dual-band What is the Proper RF Coverage for my Raven?What Type of Antenna is Best for my Raven? DipoleMounts What do I need to power my Raven ?Can I use a portable battery to power my Raven ? 103 Public Mode *HOSTPRIVMODE=0 Private Mode *HOSTPRIVMODE=1What is the COM1000? 105Wireless ACE Wireless ACE Update PRLWireless ACE Update PRL interface AT Commands108 Support web site Contacting Technical Support