Airlink CDMA/1x manual Power Management, Power consumption, Serial Port Pin-outs

Page 55

Humidity: 5%-95% Non-condensing

Power Management:

Low power consumption

Dormant connection (idle for 10-20 seconds): at 12 VDC

Input Voltage: 10 VDC to 28 VDC

Input Current: 20 mA to 350 mA

Low power mode: at 12 VDC

Power consumption

Modem

Idle

Transmitting

 

 

 

Raven C3211

50 mAh

200-300 mAh

Raven C3210

50 mAh

250-300 mAh

 

 

 

Serial Port Pin-outs

The cable between the modem and a computer or other serial device needs to be wired straight-through (pin 1 goes to pin 1, pin 2 to pin 2, etc).

Raven CDMA User Guide for Verizon, version 2.23

49

Image 55
Contents User Guide Raven Cdma User Guide for Verizon, version Contents TCP PAD Mode DNS Using Names Instead of IP addressesConfiguring Keepalive Data usage using Keepalive AT Mode PassThru Mode PPP Mode Slip Mode UDP Pad ModeSnmp Overview Appendix 1 Specifications for the Raven CdmaRaven Snmp Configuration Connecting the Antenna Connecting powerAppendix 4 Example of the MIB trap What is RSSI? Why is the Rssi for my Raven negative?Support web site Contacting Technical Support Introduction to Raven Cdma Establishing a Internet Connection Cdma OverviewUsing Cdma to Communicate with Your Equipment Financial Point of Sale and Kiosk Common Uses for the RavenBackup connection to the Internet Quick Start Guide and Setup Wizard Connecting the Raven to your computerActivation of the Raven Setup Wizard Raven Indicator Lights Activating the Raven using AT CommandsRaven Cdma User Guide for Verizon, version Utilities for the Raven Wireless ACE 3G AirLink Configuration Executive ACEAceView AceNetAceView About Modem Modem Doctor IP Manager Fully Qualified Domain Name Dynamic Name ResolutionConfiguring the Raven for Dynamic IP Restrictions for Modem Name Wireless ACE Dynamic IP IP Manager configurationConfiguring DNS DNS Using Names Instead of IP addressesPPP-Peer Keepalive Configuring KeepaliveWireless ACE Keepalive Configuration Data usage using KeepaliveHost Modes AT Mode PassThru Mode Slip Mode PPP ModeATDT10.0.0.1CR ATDT10001CR ATD#19788CR UDP Auto Answer UDP Pad ModeReliable UDP Multicast UDP TCP PAD ModeTCP Auto Answer Hybrid ModesHybrid Mode Settings Modbus Overview Modbus/BSAP ConfigurationProgrammable Logic Controller PLC TelemetryRemote Terminal Unit RTU Supervisory Control and Data Acquisition ScadaRaven Modbus on UDP Modbus TCP/IPDefault Power-up Mode Configuring the Raven at the Polling Host for Modbus on UDPPort Dynamic IP IDs to IPsWireless ACE Modem Name and Domain Configuring the Remote Ravens for Modbus withDynamic IPs Host Raven IPRaven mounted in an enclosure with an RTU RTU settingsRTU to Raven setup Snmp Overview Simple Network Management Protocol SnmpListening Port Raven Snmp ConfigurationManagement Information Base MIB Snmp TrapsSecurity Level User Name and PasswordWireless ACE Changing the Raven Password Menu Option Trap Destination Connecting the Antenna Hardware InstallationConnecting the Raven to a computer or other device Connecting powerEnvironmental Specifications for the Raven CdmaPhysical Characteristics Data Services & RF Features CdmaPower consumption Power ManagementSerial Port Pin-outs Raven Cdma User Guide for Verizon, version Raven Mounting Bracket, part number 100-170-1009 a Mounting KitRaven Cdma User Guide for Verizon, version Using Wireless Ace AT CommandsWireless ACE Using AT Commands Using Telnet Terminal EmulationStartAll ProgramsAccessoriesCommunicationsHyperTerminal Direct Serial Connection HyperTerminal AT mode via TelnetHyperTerminal Comport Setting AT Command TablesInformation Commands Information and Status Command DetailsRaven Basic Commands common AT commands Basic CommandsNone Activation Activation Provisioning Cellular Network Verizon’s Cdma Cellular NetworkPassThru Local Network and Host ModesLocal Network and Host Modes This command is not pro Ceeded by ATStopbits = S23=speed,databits Speed =Paritystop bits Databits = 7 or Itystop bits Parity =Figured to ignore DTR. When Ignore DTR is enabled Slip Default N.n = subnet AtdtPPP Direct Communication Telnet When *CSX1=0Direct Communication Ppppp S53=methodd.d.d.d Method =Port Hhmmss = Time and DateMm/dd/yyyy = Yyyy,hhmmssDNSn=d.d.d.d Friends ModeFriends Mode Fn=d.d.d.dKeepalive If *DOMAIN=eairlink.com, then when IP ManagerExample if *MODEMNAME=mymodem Raven Cdma User Guide for Verizon, version Modbus LoggingD.d=IP or Modbus SettingsCannot be configured in Wireless ACE MLISTid=d.d.d.dLow order 4 bits D.d = IP or Snmp Simple Network Management ProtocolSMTP/SMS Name= Smtp email and SMS messagingNumber= SMS NumberFlag=2 Index=0-9C3211 Flag=0 Flag=1Other Other Settings AIRLINK-MIB Definitions = Begin Imports Example of the MIB trapRaven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version Raven Cdma User Guide for Verizon, version END Raven Cdma User Guide for Verizon, version What is RSSI? Why is the Rssi for my Raven negative? Frequently Asked Questions FAQ and SolutionsDipole What is the Proper RF Coverage for my Raven?What Type of Antenna is Best for my Raven? Dual-bandCan I use a portable battery to power my Raven ? What do I need to power my Raven ?Mounts 103 Private Mode *HOSTPRIVMODE=1 Public Mode *HOSTPRIVMODE=0105 What is the COM1000?Wireless ACE Update PRL Wireless ACEAT Commands Wireless ACE Update PRL interface108 Contacting Technical Support Support web site