Samsung CLP-650 Series Printer Install Indicated color, Color Toner, Still occurs, contact an

Message	Status	Do this...
Engine Fuser	The temperature in	Unplug the power cord and
Low Heat Error	the fuser is abnormally	plug it in again. If the problem
	low.	persists, call for service.
Engine Fuser	The temperature in	Unplug the power cord and
Over Heat Error	the fuser is abnormally	plug it in again. If the problem
	high.	persists, call for service.
Engine Fuser	A problem has	Unplug the power cord and
Inverter Error	occurred in the Fuser	plug it in again. If the problem
	in the printer.	persists, call for service.
Engine LSU	A problem has	Unplug the power cord and
Error	occurred in the LSU	plug it in again. If the problem
	(Laser Scanning Unit)	persists, call for service.
	in the printer.
Install	The indicated color	Install the corresponding color
[Color] Toner	toner cartridge is not	toner cartridge.
	installed in the printer.
Install	The paper transfer belt	Install the paper transfer belt.
Transfer Belt	is not installed in the
	printer.
Invalid Toner	An invalid toner	Only install Samsung toner
[Color]	cartridge has been	cartridges, designed for your
	installed.	printer. Or install the toner
		cartridge into each proper
		cartridge slot. If you have
		installed an Samsung toner
		cartridge or into each proper
		caartridge slot and this error
		still occurs, contact an
		authorized service agent.
Invalid	An invalid paper	Only install Samsung paper
Transfer Belt	transfer belt has been	transfer belts, designed for
	installed.	your printer. If you have
		installed an Samsung paper
		transfer belt and this error still
		occurs, contact an authorized
		service agent.
Jam0 In Tray1	A paper jam has	Remove the jammed paper
Jam0 In Tray2	occurred in or near the	from the corresponding tray,
	indicated tray.	referring to page 7.4.
Jam0 In MP Tray
Jam	A paper jam has	Remove the jammed paper
In Exit Area	occurred in the paper	from the printer, referring to
	exit area.	page 7.7.
Jam	A paper jam has	Open the access door and
Inside Printer	occurred inside the	remove the jammed paper
	printer.	from the printer, referring to
		page 7.6.

Message	Status	Do this...
Load	The paper size	Load the correct paper in the
[Size] In Tray1	specified in the printer	tray.
Load	properties does not
	match the paper you
[Size] In Tray2
	are loading.
Load
[Size] In MP
Low Density	The amount of the	Replace the toner cartridge(s)
	toner which is spread	with a new one. See page 6.4.
	on the paper transfer	If you still have the same
	belt for adjusting auto	problem, contact a service
	color registration is	representative.
	very small, so that the
	printer does not
	recognize the toner
	during auto color
	registration.
Left Fan Error	A problem has	Unplug the power cord and
	occurred in the Left	plug it in again. If the problem
	Fan of the printer.	persists, call for service.
Main Motor	A problem has	Unplug the power cord and
Error	occurred in the	plug it in again. If the problem
	development motor of	persists, call for service.
	the printer.
Memory	The printer does not	The job automatically clears
Overflow	have enough memory	and the printer returns to
	to print the current	Standby Mode.
	job.	Lower the print resolution and
	An error has occurred	try again.
	in the firmware
	program of the printer.
Paper Empty	The paper tray has run	Load paper in the paper tray.
[Size] In Tray1	out of paper.	See page 4.2.
Paper Empty
[Size] In Tray2
Paper Empty
[Size] In Mp
Paper Empty
[Size] In
Manual
Photo LED error	During auto color	Contact a service
	registration, the	representative.
	printer does not
	recognize the photo
	LED in the paper
	transfer belt assembly.

7.15

Solving Problems