Pelco TLR3168 operation manual Controls, Front Panel, PLAY/REC Check

Page 18

CONTROLS

FRONT PANEL

1

POWER

EJECT

	REC/PLAY	TRACKING	POSITON/
PICTURE	REC/PLAY	TRACKING	VERTICAL
PICTURE	MODE		ADJUST
SOFT SHARP

8

9 10 11

12

2

400

FLUORESCENT

DISPLAY

3 4 5 7

		6
JOG/ADJUST	SHUTTLE
CLEAR/	ENTER/
REW	FW
	MENU/	PLAY/
	TIME DATE ADJUST REC CHECK
		STOP
REC
	COUNTER	PAUSE/
	RESET	SUTTLE HOLD
	SEARCH	TIMER REC

13	14	15
13	14	16 17
		00440

Figure 9. Front Panel

1.POWER button

Press for on; press again for off. The POWER indicator lights when the VCR is turned on.

2.Cassette loading slot

Insert the cassette in this slot to load it.

3.SHUTTLE ring

Use to adjust the playback speed and to program the menus. Turn this ring to the right to advance the tape or to forward search. Turn it to the left to rewind a tape or to reverse search. You can also use it to clear the alarm list, timer recording, and to initialize the menu programming. It also lets you program or exit the menus after setup.

4.JOG dial

Use to advance or reverse the tape frame-by-frame and to program the menus.

5.MENU/TIME DATE ADJUST button

•When the VCR is turned on, press to display the Main menu. Press again to exit the menu.

•When the VCR is turned off, press for more than three seconds and you can adjust the VCR’s time and date on the fluorescent display.

6.PLAY/REC CHECK

•When the VCR is in stop mode, press to play back a previously recorded tape.

•During recording, press for more than 1.5 seconds to check the recording function.

7.STOP button

Press to halt all tape-related functions.

8.PICTURE control

Use this control to adjust picture quality between soft and sharp.

9.REC/PLAY MODE buttons (+/-)

Press to select the recording or playback speed.

10.TRACKING buttons (+/-)

Press to reduce or eliminate the noise during playback, slow playback, etc.

18	Pelco Manual C673M (2/01)

Image 18

Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Illustrations List of TablesGeneral AvertissementSAFEGUARDS, WARNINGS, CAUTIONS, and Care Lightning/Power Surges CleaningAccessories When Not In UseUnpacking Instructions Introduction to TIME-LAPSE RecordersTLR3168 Features and Functions Quick Start Basic StartAdditional Items Securing the VCR Controls InstallationPRE-INSTALLATION Cautions Monitor TipsInstallation Typical System SetupConnecting the VCR to a Multiplexer Connecting a VCR to a MultiplexerAlarm Recording Connection Connecting for Series RecordingConnecting for Remote Recording Connecting for Synchronous Recording Connecting for External Time Clock AdjustmentConnecting the VCR to a PC Connecting to a PC for Remote ControlTable A. RS-232C Protocol Cable Connections Controls Front PanelPLAY/REC Check Eject button POSITION/VERTICAL Adjust buttons +Timer REC button Search buttonFluorescent Display Emgcy emergency recording indicator Timer Recording indicatorTape Remaining indicator LOCK/LOCK a indicatorMode OUT Rear PanelCall OUT Using the Shuttle Ring Adjusting the Clock and Using the JOG and Shuttle ControlsUsing the JOG Dial JOG and Shuttle ControlsAdjusting the Clock Adjusting to the Exact SecondLanguage Selection Menu ProgrammingGeneral Programming Instructions MenuProgram to Record Holiday SET UP Quick Guide to the Menu StructureTIME/DATE Size Display Menu Display ModeMain Menu Blue BackTimer Program START/ENDRecording SET UP Menu Wrngtape END Wrngremain Tape END SettingRear Terminal Menu Clock OUTREC Maintenance Menu First Time SET UP MenuRS-232C Menu Additional Material DAY and Time Display ModesSET the DAY and Time Main Menu DisplayLOADING, UNLOADING, Protecting the Tape Cassette LoadingUnloading When to Replace a TapeTable C. Tape Replacement by Use Preventing Accidental ErasureRecording Manual RecordingAudio RECORDING/PLAYBACK Recording ModeRecording Check Function Repeat RecordingTable E. Action When Tape End Is Reached by Setting Stop Rewind Repeat AlarmprotSeries Recording Remote Recording ONE-SHOT/INTERVAL RecordingSynchronous Recording Synchronous Recording SequenceTimer Recording Programming ProcedureWhat if the Timer Recording Indicator Starts FLASHING? Holiday SET UPSpecial DW Setting Overlapping ProgramsAlarm Recording Table G. Minimum Interval Between RecordingsProgramming for Alarm Recording Power Loss List MaintenanceRecording After a Power Failure Viewing the Power Loss ListClearing the Alarm List Alarm ListViewing the Alarm List ALL Menu Initialize ResetElapsed Time and Repeat Recording Times Display Elapsed TimeRepeat REC Times Playback Procedure PlaybackEND of Tape Playback ModeAudio Playback Special Effects PlaybackShuttle Ring Direct Shuttle RingAdjusting the Picture During Playback Tracking Adjustment Adjusting Picture QualityVertical Vibration Adjustment Search Techniques Counter Memory StopSkip Search HOW to Count the Index Number Index SearchTime and Date Search Additional Functions and Features Using with a PC Assigning the RS-S32C SettingsCommands from a PC When Controlling only ONE VCRSending Commands Status or Error Code from Meaning When Controlling Multiple Vcrs Commands When Controlling Multiple VCRsVCR01, RC CR Commands and Responses Chart Commands Functions Status After Normal Explanation of StatusOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Initial System Testing TestingError Codes Regular System TestingTable J. Warning Display and Actions TroubleshootingSELF-DIAGNOSTIC Function and Warning Display Fluorescent Monitor Cause Remedy To Turn Off DisplayBefore Calling for Service Symptom RemedyRecording Problems Video and Audio SpecificationsElectrical MechanicalVideo Audio Tape Mode 120/T-160 Mm/s Field Fields/s Table K. Tape Speed and Recording TimeIndex Pelco Manual C673M 2/01 Regulatory Notices Revision History