Pelco TLR3168 operation manual Manual Recording

Page 37

RECORDING

MANUAL RECORDING

1

REMOTE

EJECT

	REC/PLAY	TRACKING	POSITON/
PICTURE	REC/PLAY	TRACKING	VERTICAL
PICTURE	MODE		ADJUST
SOFT SHARP

2

400

4

53

67 10

JOG/ADJUST SHUTTLE

CLEAR/	ENTER/
REW	FW

MENU/ PLAY/

TIME DATE ADJUST REC CHECK

STOP

REC

COUNTER PAUSE/

RESET SUTTLE HOLD

SEARCH TIMER REC

NOTE: Perform steps 3-7 to activate super resolution recording mode. Otherwise, skip to step 8.

8

9

00461

1.Turn on the VCR and peripheral devices.

2.Load a cassette with the erasure prevention tab intact.

3.Press the MENU button. The Main menu appears.

4.Turn the JOG dial to select RECORDING SET UP, and then turn the SHUTTLE ring right. The Recording Set Up menu appears.

5.Turn the JOG dial to select SUPER RESOLUTION, and then turn the SHUTTLE ring right.

6.Turn the JOG dial to select ON, and then turn the SHUTTLE ring right.

7.Press the MENU button. The day and time display appears on the screen.

8.Press the REC/PLAY MODE button to select the desired recording mode. Refer to Table D for recording and playback times.

9.Press the REC button to begin recording.

10.Press the STOP button to stop recording.

Keep the following in mind:

•Press the PAUSE button to momentarily stop recording. Press again to resume recording.

•To protect the tape, pause mode is automatically cancelled after about five minutes.

•If the tape you insert in the VCR has the erase prevention tab removed, the VCR will eject it if you try recording on it.

•The REC button will not work unless the VCR is in stop or pause mode.

•A tape recorded on this VCR may or may not play back correctly on another VCR.

Pelco Manual C673M (2/01)

37

Image 37

Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Tables List of IllustrationsAvertissement GeneralSAFEGUARDS, WARNINGS, CAUTIONS, and Care Accessories CleaningLightning/Power Surges When Not In UseIntroduction to TIME-LAPSE Recorders Unpacking InstructionsTLR3168 Features and Functions Basic Start Quick StartAdditional Items PRE-INSTALLATION Cautions InstallationSecuring the VCR Controls Monitor TipsTypical System Setup InstallationConnecting a VCR to a Multiplexer Connecting the VCR to a MultiplexerConnecting for Series Recording Alarm Recording ConnectionConnecting for Remote Recording Connecting for External Time Clock Adjustment Connecting for Synchronous RecordingConnecting to a PC for Remote Control Connecting the VCR to a PCTable A. RS-232C Protocol Cable Connections Front Panel ControlsPLAY/REC Check Timer REC button POSITION/VERTICAL Adjust buttons +Eject button Search buttonFluorescent Display Tape Remaining indicator Timer Recording indicatorEmgcy emergency recording indicator LOCK/LOCK a indicatorRear Panel Mode OUTCall OUT Using the JOG Dial Adjusting the Clock and Using the JOG and Shuttle ControlsUsing the Shuttle Ring JOG and Shuttle ControlsAdjusting to the Exact Second Adjusting the ClockGeneral Programming Instructions ProgrammingLanguage Selection Menu MenuQuick Guide to the Menu Structure Program to Record Holiday SET UPMain Menu Display Menu Display ModeTIME/DATE Size Blue BackSTART/END Timer ProgramRecording SET UP Menu Rear Terminal Menu SettingWrngtape END Wrngremain Tape END Clock OUTREC First Time SET UP Menu Maintenance MenuAdditional Material DAY and Time Display Modes RS-232C MenuMain Menu Display SET the DAY and TimeLoading LOADING, UNLOADING, Protecting the Tape CassetteTable C. Tape Replacement by Use When to Replace a TapeUnloading Preventing Accidental ErasureManual Recording RecordingRecording Check Function Recording ModeAudio RECORDING/PLAYBACK Repeat RecordingStop Rewind Repeat Alarmprot Table E. Action When Tape End Is Reached by SettingSeries Recording ONE-SHOT/INTERVAL Recording Remote RecordingSynchronous Recording Sequence Synchronous RecordingProgramming Procedure Timer RecordingSpecial DW Setting Holiday SET UPWhat if the Timer Recording Indicator Starts FLASHING? Overlapping ProgramsTable G. Minimum Interval Between Recordings Alarm RecordingProgramming for Alarm Recording Recording After a Power Failure MaintenancePower Loss List Viewing the Power Loss ListViewing the Alarm List Alarm ListClearing the Alarm List ALL Menu Initialize ResetElapsed Time Elapsed Time and Repeat Recording Times DisplayRepeat REC Times Playback Playback ProcedureAudio Playback Playback ModeEND of Tape Special Effects PlaybackDirect Shuttle Ring Shuttle RingAdjusting Picture Quality Adjusting the Picture During Playback Tracking AdjustmentVertical Vibration Adjustment Counter Memory Stop Search TechniquesSkip Search Index Search HOW to Count the Index NumberTime and Date Search Additional Functions and Features Assigning the RS-S32C Settings Using with a PCWhen Controlling only ONE VCR Commands from a PCSending Commands Status or Error Code from Meaning Commands When Controlling Multiple VCRs When Controlling Multiple VcrsVCR01, RC CR Commands Functions Status After Normal Explanation of Status Commands and Responses ChartOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Error Codes TestingInitial System Testing Regular System TestingSELF-DIAGNOSTIC Function and Warning Display TroubleshootingTable J. Warning Display and Actions Fluorescent Monitor Cause Remedy To Turn Off DisplaySymptom Remedy Before Calling for ServiceRecording Problems Electrical SpecificationsVideo and Audio MechanicalTable K. Tape Speed and Recording Time Video Audio Tape Mode 120/T-160 Mm/s Field Fields/sIndex Pelco Manual C673M 2/01 Revision History Regulatory Notices