Pelco TLR3168 operation manual Remote Recording, ONE-SHOT/INTERVAL Recording

Page 40

REMOTE RECORDING

This function lets you control the start and end of recording from a remote location. The VCR starts recording when the REC IN terminal is grounded. Refer to Figure 5 for the remote recording connection.

An index signal is not recorded during remote recording. Series and timer recording cannot be used simultaneously with remote recording.

1.Press the MENU button. The Main menu appears.

2.Turn the JOG dial to select REAR TERMINAL, and then turn the SHUTTLE ring right. The Rear Terminal menu appears.

3.Set REC IN to REC-START/STOP.

4.Press the MENU button. The day and time display appears on screen.

ONE-SHOT/INTERVAL RECORDING

One-shot recording lets you control the number of fields to be recorded when the REC button is pressed or the REC IN terminal is grounded. Interval recording is made at the selected number of fields and at the selected interval.

1.Press the REC/PLAY MODE button on the front panel to set the recording mode to 0H.

2.Press the MENU button. The Main menu appears.

3.Turn the JOG dial to select RECORDING SET UP, and then turn the SHUTTLE ring right. The Recording Set Up menu appears.

4.Turn the JOG dial to select ONE SHOT•INTERVAL, and then turn the SHUTTLE ring right.

5.Turn the JOG dial to select the number of fields to record, and then turn the SHUTTLE ring right.

6.Turn the JOG dial to select ONE SHOT•INTERVAL, and then turn the SHUTTLE ring right.

7.Do one of the following:

•If setting up one-shot recording:

Turn the JOG dial to select SHOT, and then turn the SHUTTLE ring right.

•If setting up interval recording:

Turn the JOG dial to select the recording interval, and then turn the SHUTTLE ring right.

8.Press the REC button. One of the following will occur:

•One-shot recording will be in standby mode.

•The VCR starts interval recording with the interval time you chose in step 7.

9.To start one-shot recording, press the REC button again or switch the REC IN terminal on the rear panel to the ground.

40	Pelco Manual C673M (2/01)

Image 40

Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Illustrations List of TablesGeneral AvertissementSAFEGUARDS, WARNINGS, CAUTIONS, and Care Cleaning AccessoriesLightning/Power Surges When Not In UseUnpacking Instructions Introduction to TIME-LAPSE RecordersTLR3168 Features and Functions Basic Start Quick StartAdditional Items Installation PRE-INSTALLATION CautionsSecuring the VCR Controls Monitor TipsInstallation Typical System SetupConnecting the VCR to a Multiplexer Connecting a VCR to a MultiplexerConnecting for Series Recording Alarm Recording ConnectionConnecting for Remote Recording Connecting for Synchronous Recording Connecting for External Time Clock AdjustmentConnecting to a PC for Remote Control Connecting the VCR to a PCTable A. RS-232C Protocol Cable Connections Front Panel ControlsPLAY/REC Check POSITION/VERTICAL Adjust buttons + Timer REC buttonEject button Search buttonFluorescent Display Timer Recording indicator Tape Remaining indicatorEmgcy emergency recording indicator LOCK/LOCK a indicatorRear Panel Mode OUTCall OUT Adjusting the Clock and Using the JOG and Shuttle Controls Using the JOG DialUsing the Shuttle Ring JOG and Shuttle ControlsAdjusting the Clock Adjusting to the Exact SecondProgramming General Programming InstructionsLanguage Selection Menu MenuProgram to Record Holiday SET UP Quick Guide to the Menu StructureDisplay Menu Display Mode Main MenuTIME/DATE Size Blue BackTimer Program START/ENDRecording SET UP Menu Setting Rear Terminal MenuWrngtape END Wrngremain Tape END Clock OUTREC Maintenance Menu First Time SET UP MenuRS-232C Menu Additional Material DAY and Time Display ModesSET the DAY and Time Main Menu DisplayLOADING, UNLOADING, Protecting the Tape Cassette LoadingWhen to Replace a Tape Table C. Tape Replacement by UseUnloading Preventing Accidental ErasureRecording Manual RecordingRecording Mode Recording Check FunctionAudio RECORDING/PLAYBACK Repeat RecordingStop Rewind Repeat Alarmprot Table E. Action When Tape End Is Reached by SettingSeries Recording Remote Recording ONE-SHOT/INTERVAL RecordingSynchronous Recording Synchronous Recording SequenceTimer Recording Programming ProcedureHoliday SET UP Special DW SettingWhat if the Timer Recording Indicator Starts FLASHING? Overlapping ProgramsAlarm Recording Table G. Minimum Interval Between RecordingsProgramming for Alarm Recording Maintenance Recording After a Power FailurePower Loss List Viewing the Power Loss ListAlarm List Viewing the Alarm ListClearing the Alarm List ALL Menu Initialize ResetElapsed Time Elapsed Time and Repeat Recording Times DisplayRepeat REC Times Playback Procedure PlaybackPlayback Mode Audio PlaybackEND of Tape Special Effects PlaybackShuttle Ring Direct Shuttle RingAdjusting the Picture During Playback Tracking Adjustment Adjusting Picture QualityVertical Vibration Adjustment Counter Memory Stop Search TechniquesSkip Search HOW to Count the Index Number Index SearchTime and Date Search Additional Functions and Features Using with a PC Assigning the RS-S32C SettingsWhen Controlling only ONE VCR Commands from a PCSending Commands Status or Error Code from Meaning When Controlling Multiple Vcrs Commands When Controlling Multiple VCRsVCR01, RC CR Commands and Responses Chart Commands Functions Status After Normal Explanation of StatusOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Testing Error CodesInitial System Testing Regular System TestingTroubleshooting SELF-DIAGNOSTIC Function and Warning DisplayTable J. Warning Display and Actions Fluorescent Monitor Cause Remedy To Turn Off DisplayBefore Calling for Service Symptom RemedyRecording Problems Specifications ElectricalVideo and Audio MechanicalVideo Audio Tape Mode 120/T-160 Mm/s Field Fields/s Table K. Tape Speed and Recording TimeIndex Pelco Manual C673M 2/01 Regulatory Notices Revision History