Pelco TLR3168 operation manual Fluorescent Display

Page 20

FLUORESCENT DISPLAY

1	2	3	4	5	6	7	9	11	12 13
						8	10
						400

1415 16 17 18 19

00441

Figure 10. Fluorescent Display

1.M (counter memory stop/month) indicator

•Lights during counter memory stop.

•Also, lights when the month (of time and date) is being entered through the front panel.

2.PL (power loss) indicator

Lights when the VCR is turned on after a power failure during recording.

3.ALARM (recording) indicator

Flashes during alarm recording and stays on when the alarm recording is finished.

4.D (time and date search/day) indicator

•Lights during the time and date search.

•Also, lights when the day (of time and date) is being entered through the front panel.

5.INDEX (index search) indicator

Flashes when recording an index signal, and lights during the index number setup and the index search. (Index number is shown on the Recording and Playback Mode display.)

6.SKIP (skip search) indicator Lights during a skip search.

7.Daylight savings time indicator

Lights when DAYLIGHT SAVINGS is set to ON.

8.SP, EP (tape speed) indicator

Indicates the tape speed (SP = standard play, EP = extended play).

9.400 (super resolution) indicator

Lights during recording using VHS tape, during playback using VHS tape recorded in super resolution mode, and when a VHS tape recorded in super resolution mode is inserted in the VCR (provided SUPER RESOLUTION in the Recording Set Up menu is set ON).

10.Repeat indicator

Lights when TAPE END in the First Time Set Up menu is set to REPEAT or

ALARM•PROT.

11.Cassette Status indicator

Lights when you insert a tape. The light advances, stops, or flashes according to tape movement.

20	Pelco Manual C673M (2/01)

Image 20

Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Illustrations List of TablesGeneral AvertissementSAFEGUARDS, WARNINGS, CAUTIONS, and Care Cleaning AccessoriesLightning/Power Surges When Not In UseUnpacking Instructions Introduction to TIME-LAPSE RecordersTLR3168 Features and Functions Additional Items Quick StartBasic Start Installation PRE-INSTALLATION CautionsSecuring the VCR Controls Monitor TipsInstallation Typical System SetupConnecting the VCR to a Multiplexer Connecting a VCR to a MultiplexerConnecting for Remote Recording Alarm Recording ConnectionConnecting for Series Recording Connecting for Synchronous Recording Connecting for External Time Clock AdjustmentTable A. RS-232C Protocol Connecting the VCR to a PCConnecting to a PC for Remote Control Cable Connections PLAY/REC Check ControlsFront Panel POSITION/VERTICAL Adjust buttons + Timer REC buttonEject button Search buttonFluorescent Display Timer Recording indicator Tape Remaining indicatorEmgcy emergency recording indicator LOCK/LOCK a indicatorCall OUT Mode OUTRear Panel Adjusting the Clock and Using the JOG and Shuttle Controls Using the JOG DialUsing the Shuttle Ring JOG and Shuttle ControlsAdjusting the Clock Adjusting to the Exact SecondProgramming General Programming InstructionsLanguage Selection Menu MenuProgram to Record Holiday SET UP Quick Guide to the Menu StructureDisplay Menu Display Mode Main MenuTIME/DATE Size Blue BackTimer Program START/ENDRecording SET UP Menu Setting Rear Terminal MenuWrngtape END Wrngremain Tape END Clock OUTREC Maintenance Menu First Time SET UP MenuRS-232C Menu Additional Material DAY and Time Display ModesSET the DAY and Time Main Menu DisplayLOADING, UNLOADING, Protecting the Tape Cassette LoadingWhen to Replace a Tape Table C. Tape Replacement by UseUnloading Preventing Accidental ErasureRecording Manual RecordingRecording Mode Recording Check FunctionAudio RECORDING/PLAYBACK Repeat RecordingSeries Recording Table E. Action When Tape End Is Reached by SettingStop Rewind Repeat Alarmprot Remote Recording ONE-SHOT/INTERVAL RecordingSynchronous Recording Synchronous Recording SequenceTimer Recording Programming ProcedureHoliday SET UP Special DW SettingWhat if the Timer Recording Indicator Starts FLASHING? Overlapping ProgramsAlarm Recording Table G. Minimum Interval Between RecordingsProgramming for Alarm Recording Maintenance Recording After a Power FailurePower Loss List Viewing the Power Loss ListAlarm List Viewing the Alarm ListClearing the Alarm List ALL Menu Initialize ResetRepeat REC Times Elapsed Time and Repeat Recording Times DisplayElapsed Time Playback Procedure PlaybackPlayback Mode Audio PlaybackEND of Tape Special Effects PlaybackShuttle Ring Direct Shuttle RingAdjusting the Picture During Playback Tracking Adjustment Adjusting Picture QualityVertical Vibration Adjustment Skip Search Search TechniquesCounter Memory Stop HOW to Count the Index Number Index SearchTime and Date Search Additional Functions and Features Using with a PC Assigning the RS-S32C SettingsSending Commands Status or Error Code from Meaning Commands from a PCWhen Controlling only ONE VCR When Controlling Multiple Vcrs Commands When Controlling Multiple VCRsVCR01, RC CR Commands and Responses Chart Commands Functions Status After Normal Explanation of StatusOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Testing Error CodesInitial System Testing Regular System TestingTroubleshooting SELF-DIAGNOSTIC Function and Warning DisplayTable J. Warning Display and Actions Fluorescent Monitor Cause Remedy To Turn Off DisplayBefore Calling for Service Symptom RemedyRecording Problems Specifications ElectricalVideo and Audio MechanicalVideo Audio Tape Mode 120/T-160 Mm/s Field Fields/s Table K. Tape Speed and Recording TimeIndex Pelco Manual C673M 2/01 Regulatory Notices Revision History