Pelco TLR3168 Adjusting the Clock and Using the JOG and Shuttle Controls, Using the JOG Dial

Page 23

5.MIC jack

Jack for connecting a microphone rated at 600 ohms impedance.

6.AUDIO IN connector

Audio input connector (RCA pin).

7.AUDIO OUT connector

Audio output connector (RCA pin).

8.VIDEO IN connector

Input connector for video signal (BNC connector). Connect cameras here.

9.VIDEO OUT connector

Output connector for video signal (BNC connector). Connect a monitor here.

10.RESET button

Press to erase the date, present time, alarm recording list, power loss list, and the number of tape uses; and reset them to their default values. Power to the VCR is cut off while the button is pressed. If there is a tape in the VCR and the button is released, the power indicator lights and the tape fast forwards for a few seconds. The VCR then turns off.

11.RS-232 terminal (DB9)

Input terminal for connecting a PC using an RS-232C crossed cable.

ADJUSTING THE CLOCK AND USING THE JOG AND SHUTTLE CONTROLS

JOG AND SHUTTLE CONTROLS

JOG DIAL

JOG/ADJUST SHUTTLE

CLEAR/	ENTER/
REW	FW

MENU/ PLAY/

TIME DATE ADJUST REC CHECK

STOP

COUNTER PAUSE/

RESET SUTTLE HOLD

SEARCH TIMER REC

SHUTTLE RING

00443

Figure 12. JOG Dial and SHUTTLE Ring

USING THE JOG DIAL

•Turn by using your finger on the indent.

•Turning the JOG dial right advances you through the options while turning left reverses direction.

•When the option is not flashing, turn right to move the cursor downward, turn left to move upward.

USING THE SHUTTLE RING

•The SHUTTLE ring automatically centers itself if you turn it fully right/left and release it.

•Some menus move down to the next layer when you turn the SHUTTLE ring right. Turning it left returns to the previous layer.

Pelco Manual C673M (2/01)

23

Image 23

Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Tables List of IllustrationsAvertissement GeneralSAFEGUARDS, WARNINGS, CAUTIONS, and Care When Not In Use CleaningAccessories Lightning/Power SurgesIntroduction to TIME-LAPSE Recorders Unpacking InstructionsTLR3168 Features and Functions Additional Items Quick StartBasic Start Monitor Tips InstallationPRE-INSTALLATION Cautions Securing the VCR ControlsTypical System Setup InstallationConnecting a VCR to a Multiplexer Connecting the VCR to a MultiplexerConnecting for Remote Recording Alarm Recording ConnectionConnecting for Series Recording Connecting for External Time Clock Adjustment Connecting for Synchronous RecordingTable A. RS-232C Protocol Connecting the VCR to a PCConnecting to a PC for Remote Control Cable Connections PLAY/REC Check ControlsFront Panel Search button POSITION/VERTICAL Adjust buttons +Timer REC button Eject buttonFluorescent Display LOCK/LOCK a indicator Timer Recording indicatorTape Remaining indicator Emgcy emergency recording indicatorCall OUT Mode OUTRear Panel JOG and Shuttle Controls Adjusting the Clock and Using the JOG and Shuttle ControlsUsing the JOG Dial Using the Shuttle RingAdjusting to the Exact Second Adjusting the ClockMenu ProgrammingGeneral Programming Instructions Language Selection MenuQuick Guide to the Menu Structure Program to Record Holiday SET UPBlue Back Display Menu Display ModeMain Menu TIME/DATE SizeSTART/END Timer ProgramRecording SET UP Menu Clock OUT SettingRear Terminal Menu Wrngtape END Wrngremain Tape ENDREC First Time SET UP Menu Maintenance MenuAdditional Material DAY and Time Display Modes RS-232C MenuMain Menu Display SET the DAY and TimeLoading LOADING, UNLOADING, Protecting the Tape CassettePreventing Accidental Erasure When to Replace a TapeTable C. Tape Replacement by Use UnloadingManual Recording RecordingRepeat Recording Recording ModeRecording Check Function Audio RECORDING/PLAYBACKSeries Recording Table E. Action When Tape End Is Reached by SettingStop Rewind Repeat Alarmprot ONE-SHOT/INTERVAL Recording Remote RecordingSynchronous Recording Sequence Synchronous RecordingProgramming Procedure Timer RecordingOverlapping Programs Holiday SET UPSpecial DW Setting What if the Timer Recording Indicator Starts FLASHING?Table G. Minimum Interval Between Recordings Alarm RecordingProgramming for Alarm Recording Viewing the Power Loss List MaintenanceRecording After a Power Failure Power Loss ListALL Menu Initialize Reset Alarm ListViewing the Alarm List Clearing the Alarm ListRepeat REC Times Elapsed Time and Repeat Recording Times DisplayElapsed Time Playback Playback ProcedureSpecial Effects Playback Playback ModeAudio Playback END of TapeDirect Shuttle Ring Shuttle RingAdjusting Picture Quality Adjusting the Picture During Playback Tracking AdjustmentVertical Vibration Adjustment Skip Search Search TechniquesCounter Memory Stop Index Search HOW to Count the Index NumberTime and Date Search Additional Functions and Features Assigning the RS-S32C Settings Using with a PCSending Commands Status or Error Code from Meaning Commands from a PCWhen Controlling only ONE VCR Commands When Controlling Multiple VCRs When Controlling Multiple VcrsVCR01, RC CR Commands Functions Status After Normal Explanation of Status Commands and Responses ChartOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Regular System Testing TestingError Codes Initial System TestingFluorescent Monitor Cause Remedy To Turn Off Display TroubleshootingSELF-DIAGNOSTIC Function and Warning Display Table J. Warning Display and ActionsSymptom Remedy Before Calling for ServiceRecording Problems Mechanical SpecificationsElectrical Video and AudioTable K. Tape Speed and Recording Time Video Audio Tape Mode 120/T-160 Mm/s Field Fields/sIndex Pelco Manual C673M 2/01 Revision History Regulatory Notices