Pelco TLR3168 operation manual Rear Panel, Mode OUT, Call OUT

Page 22

REAR PANEL

WARNING: The included power cord is used for 120 VAC, 60 Hz. Never connect the power cord to any output or power supply having a dif- ferent voltage or frequency.

Make sure the power cord is unplugged before making any rear panel terminal connections.

1		2				3
					BATTERY	OPEN
ALM RST REC GND		MODE	CLK CALL
IN		OUT
REMOTE MIC	IN	OUT	IN	OUT	RESET
		AUDIO	VIDEO
5		7	8	9	10	11
4	6		8		10	11	00442

Figure 11. Rear Panel

1.AC power socket

The power cord plugs into this socket. Insert the cord firmly.

2.Terminals

•Input Terminals

ALM (alarm) IN

Use for alarm recording. Connect the alarm sensor here.

RST (reset) IN

Connect the alarm reset switch here to stop alarm recording when ALARM REC DURATION in the Recording Set Up menu is set to MAN1. You can also use this terminal to set the on-screen clock when set to any mode other than MAN1.

REC (recording) IN

Use to start and stop recording or for series recording (refer to the Series Recording section).

•GND (ground)

Connect the ground lead here when a lead connected to other terminals requires a ground.

•Output Terminals

ALM (alarm) OUT

Use to indicate to an external device that an alarm is being recorded.

MODE OUT

Use to indicate the VCR’s mode of operation. When MODE OUT in the Rear Terminal menu is set to CLOCK ADJ, the clocks of all connected VCRs can be adjusted.

CLK (clock) OUT

Use to control an external camera switcher, such as the MX4000 Series Genex Multiplexer.

CALL OUT

Use to indicate when the tape finishes recording or that there was a problem during recording.

3.Battery box

The battery is stored here. (NOTE: This is a special battery. Consult your dealer to replace it.)

4.REMOTE jack

Jack for connecting a remote control unit.

22	Pelco Manual C673M (2/01)

Image 22

Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Illustrations List of TablesGeneral AvertissementSAFEGUARDS, WARNINGS, CAUTIONS, and Care Lightning/Power Surges CleaningAccessories When Not In UseUnpacking Instructions Introduction to TIME-LAPSE RecordersTLR3168 Features and Functions Basic Start Quick StartAdditional Items Securing the VCR Controls InstallationPRE-INSTALLATION Cautions Monitor TipsInstallation Typical System SetupConnecting the VCR to a Multiplexer Connecting a VCR to a MultiplexerConnecting for Series Recording Alarm Recording ConnectionConnecting for Remote Recording Connecting for Synchronous Recording Connecting for External Time Clock AdjustmentConnecting to a PC for Remote Control Connecting the VCR to a PCTable A. RS-232C Protocol Cable Connections Front Panel ControlsPLAY/REC Check Eject button POSITION/VERTICAL Adjust buttons +Timer REC button Search buttonFluorescent Display Emgcy emergency recording indicator Timer Recording indicatorTape Remaining indicator LOCK/LOCK a indicatorRear Panel Mode OUTCall OUT Using the Shuttle Ring Adjusting the Clock and Using the JOG and Shuttle ControlsUsing the JOG Dial JOG and Shuttle ControlsAdjusting the Clock Adjusting to the Exact SecondLanguage Selection Menu ProgrammingGeneral Programming Instructions MenuProgram to Record Holiday SET UP Quick Guide to the Menu StructureTIME/DATE Size Display Menu Display ModeMain Menu Blue BackTimer Program START/ENDRecording SET UP Menu Wrngtape END Wrngremain Tape END SettingRear Terminal Menu Clock OUTREC Maintenance Menu First Time SET UP MenuRS-232C Menu Additional Material DAY and Time Display ModesSET the DAY and Time Main Menu DisplayLOADING, UNLOADING, Protecting the Tape Cassette LoadingUnloading When to Replace a TapeTable C. Tape Replacement by Use Preventing Accidental ErasureRecording Manual RecordingAudio RECORDING/PLAYBACK Recording ModeRecording Check Function Repeat RecordingStop Rewind Repeat Alarmprot Table E. Action When Tape End Is Reached by SettingSeries Recording Remote Recording ONE-SHOT/INTERVAL RecordingSynchronous Recording Synchronous Recording SequenceTimer Recording Programming ProcedureWhat if the Timer Recording Indicator Starts FLASHING? Holiday SET UPSpecial DW Setting Overlapping ProgramsAlarm Recording Table G. Minimum Interval Between RecordingsProgramming for Alarm Recording Power Loss List MaintenanceRecording After a Power Failure Viewing the Power Loss ListClearing the Alarm List Alarm ListViewing the Alarm List ALL Menu Initialize ResetElapsed Time Elapsed Time and Repeat Recording Times DisplayRepeat REC Times Playback Procedure PlaybackEND of Tape Playback ModeAudio Playback Special Effects PlaybackShuttle Ring Direct Shuttle RingAdjusting the Picture During Playback Tracking Adjustment Adjusting Picture QualityVertical Vibration Adjustment Counter Memory Stop Search TechniquesSkip Search HOW to Count the Index Number Index SearchTime and Date Search Additional Functions and Features Using with a PC Assigning the RS-S32C SettingsWhen Controlling only ONE VCR Commands from a PCSending Commands Status or Error Code from Meaning When Controlling Multiple Vcrs Commands When Controlling Multiple VCRsVCR01, RC CR Commands and Responses Chart Commands Functions Status After Normal Explanation of StatusOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Initial System Testing TestingError Codes Regular System TestingTable J. Warning Display and Actions TroubleshootingSELF-DIAGNOSTIC Function and Warning Display Fluorescent Monitor Cause Remedy To Turn Off DisplayBefore Calling for Service Symptom RemedyRecording Problems Video and Audio SpecificationsElectrical MechanicalVideo Audio Tape Mode 120/T-160 Mm/s Field Fields/s Table K. Tape Speed and Recording TimeIndex Pelco Manual C673M 2/01 Regulatory Notices Revision History