Pelco TLR3168 operation manual Adjusting the Clock, Adjusting to the Exact Second

Page 24

ADJUSTING THE CLOCK

You can adjust the VCR’s clock on the front panel even when the VCR is turned off. (You can also enter time and date information through the First Time Set Up menu.) This function lets you enter the order of the time, month, day, and year. The hour time is entered twice due to daylight savings time.

To adjust the clock:

1.When the VCR and peripheral devices are turned off, press the MENU button for more than three seconds. The hour digits on the fluorescent display’s clock start flashing.

2.Turn the JOG dial to set the hour digits. (If the flashing item is the same as the current time, turn the SHUTTLE ring without turning the JOG dial.)

3.Turn the SHUTTLE ring right to make the 10-minute digit flash, and then turn the JOG dial to adjust.

4.Turn the SHUTTLE ring right to make the 1-minute digit flash, and then turn the JOG dial to adjust. (If you want to finish the clock adjustment now, press the MENU button for more than three seconds.)

5.Turn the SHUTTLE ring right to make the month digits flash, and then turn the JOG dial to adjust. The month indicator (M) lights.

6.Turn the SHUTTLE ring right to make the day digits flash, and then turn the JOG dial to adjust. The day indicator (D) lights.

7.Turn the SHUTTLE ring right to make the year digits flash, and then turn the JOG dial to adjust.

8.Turn the SHUTTLE ring right. The VCR’s clock is now set.

9.Repeat steps 1 and 2, and then turn the SHUTTLE ring left to exit after the hour digits are entered the second time (for daylight savings time).

ADJUSTING TO THE EXACT SECOND

Set the clock as described previously, but set the minutes to one minute ahead of the time you are using as a reference. After step 7, turn the SHUTTLE ring right when the desired time reaches 00 seconds of the minute you have chosen.

24

Pelco Manual C673M (2/01)

Image 24
Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Illustrations List of TablesGeneral AvertissementSAFEGUARDS, WARNINGS, CAUTIONS, and Care Cleaning AccessoriesLightning/Power Surges When Not In UseUnpacking Instructions Introduction to TIME-LAPSE RecordersTLR3168 Features and Functions Quick Start Basic StartAdditional Items Installation PRE-INSTALLATION CautionsSecuring the VCR Controls Monitor TipsInstallation Typical System SetupConnecting the VCR to a Multiplexer Connecting a VCR to a MultiplexerAlarm Recording Connection Connecting for Series RecordingConnecting for Remote Recording Connecting for Synchronous Recording Connecting for External Time Clock AdjustmentConnecting the VCR to a PC Connecting to a PC for Remote ControlTable A. RS-232C Protocol Cable Connections Controls Front PanelPLAY/REC Check POSITION/VERTICAL Adjust buttons + Timer REC buttonEject button Search buttonFluorescent Display Timer Recording indicator Tape Remaining indicatorEmgcy emergency recording indicator LOCK/LOCK a indicatorMode OUT Rear PanelCall OUT Adjusting the Clock and Using the JOG and Shuttle Controls Using the JOG DialUsing the Shuttle Ring JOG and Shuttle ControlsAdjusting the Clock Adjusting to the Exact SecondProgramming General Programming InstructionsLanguage Selection Menu MenuProgram to Record Holiday SET UP Quick Guide to the Menu StructureDisplay Menu Display Mode Main MenuTIME/DATE Size Blue BackTimer Program START/ENDRecording SET UP Menu Setting Rear Terminal MenuWrngtape END Wrngremain Tape END Clock OUTREC Maintenance Menu First Time SET UP MenuRS-232C Menu Additional Material DAY and Time Display ModesSET the DAY and Time Main Menu DisplayLOADING, UNLOADING, Protecting the Tape Cassette LoadingWhen to Replace a Tape Table C. Tape Replacement by UseUnloading Preventing Accidental ErasureRecording Manual RecordingRecording Mode Recording Check FunctionAudio RECORDING/PLAYBACK Repeat RecordingTable E. Action When Tape End Is Reached by Setting Stop Rewind Repeat AlarmprotSeries Recording Remote Recording ONE-SHOT/INTERVAL RecordingSynchronous Recording Synchronous Recording SequenceTimer Recording Programming ProcedureHoliday SET UP Special DW SettingWhat if the Timer Recording Indicator Starts FLASHING? Overlapping ProgramsAlarm Recording Table G. Minimum Interval Between RecordingsProgramming for Alarm Recording Maintenance Recording After a Power FailurePower Loss List Viewing the Power Loss ListAlarm List Viewing the Alarm ListClearing the Alarm List ALL Menu Initialize ResetElapsed Time and Repeat Recording Times Display Elapsed TimeRepeat REC Times Playback Procedure PlaybackPlayback Mode Audio PlaybackEND of Tape Special Effects PlaybackShuttle Ring Direct Shuttle RingAdjusting the Picture During Playback Tracking Adjustment Adjusting Picture QualityVertical Vibration Adjustment Search Techniques Counter Memory StopSkip Search HOW to Count the Index Number Index SearchTime and Date Search Additional Functions and Features Using with a PC Assigning the RS-S32C SettingsCommands from a PC When Controlling only ONE VCRSending Commands Status or Error Code from Meaning When Controlling Multiple Vcrs Commands When Controlling Multiple VCRsVCR01, RC CR Commands and Responses Chart Commands Functions Status After Normal Explanation of StatusOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Testing Error CodesInitial System Testing Regular System TestingTroubleshooting SELF-DIAGNOSTIC Function and Warning DisplayTable J. Warning Display and Actions Fluorescent Monitor Cause Remedy To Turn Off DisplayBefore Calling for Service Symptom RemedyRecording Problems Specifications ElectricalVideo and Audio MechanicalVideo Audio Tape Mode 120/T-160 Mm/s Field Fields/s Table K. Tape Speed and Recording TimeIndex Pelco Manual C673M 2/01 Regulatory Notices Revision History