Pelco TLR3168 operation manual Elapsed Time and Repeat Recording Times Display, Repeat REC Times

Page 48

ELAPSED TIME AND REPEAT RECORDING TIMES DISPLAY

<MAINTENANCE> POWER LOSS LIST

ALARM LIST

ALL MENU INITIALIZE POWER LOSS LIST CLEAR ALARM LIST CLEAR

<REPEAT REC TIMES>

0

<ELAPSED TIME> 0H

00483

The repeat recording times and elapsed time are shown on the bottom of the Maintenance menu.

ELAPSED TIME

The elapsed time indicates the total time the VCR has been used for recording and playback (up to 89,999 hours). Use the elapsed time as a guide for periodic parts replacement.

REPEAT REC TIMES

•The repeat recording times field displays the number of times a tape has been recorded on when the tape ends during recording (except when TAPE END in the First Time Set Up menu is set to STOP).

•The number of tape uses is kept even if AC power is disconnected, provided the backup battery is fully charged.

•The number of tape uses is reset when a new tape is inserted.

•The number of tape uses shown can be up to 200. “OVER” appears if 200 times is exceeded.

To view:

1.Press the MENU button. The Main menu appears.

2.Turn the JOG dial to select MAINTENANCE, and then turn the SHUTTLE ring right. The Maintenance menu appears. The repeat recording times and elapsed time are shown at the bottom of the screen.

3.Press the MENU button. The day and time display appears.

48	Pelco Manual C673M (2/01)

Image 48

Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Illustrations List of TablesGeneral AvertissementSAFEGUARDS, WARNINGS, CAUTIONS, and Care Cleaning AccessoriesLightning/Power Surges When Not In UseUnpacking Instructions Introduction to TIME-LAPSE RecordersTLR3168 Features and Functions Quick Start Basic StartAdditional Items Installation PRE-INSTALLATION CautionsSecuring the VCR Controls Monitor TipsInstallation Typical System SetupConnecting the VCR to a Multiplexer Connecting a VCR to a MultiplexerAlarm Recording Connection Connecting for Series RecordingConnecting for Remote Recording Connecting for Synchronous Recording Connecting for External Time Clock AdjustmentConnecting the VCR to a PC Connecting to a PC for Remote ControlTable A. RS-232C Protocol Cable Connections Controls Front PanelPLAY/REC Check POSITION/VERTICAL Adjust buttons + Timer REC buttonEject button Search buttonFluorescent Display Timer Recording indicator Tape Remaining indicatorEmgcy emergency recording indicator LOCK/LOCK a indicatorMode OUT Rear PanelCall OUT Adjusting the Clock and Using the JOG and Shuttle Controls Using the JOG DialUsing the Shuttle Ring JOG and Shuttle ControlsAdjusting the Clock Adjusting to the Exact SecondProgramming General Programming InstructionsLanguage Selection Menu MenuProgram to Record Holiday SET UP Quick Guide to the Menu StructureDisplay Menu Display Mode Main MenuTIME/DATE Size Blue BackTimer Program START/ENDRecording SET UP Menu Setting Rear Terminal MenuWrngtape END Wrngremain Tape END Clock OUTREC Maintenance Menu First Time SET UP MenuRS-232C Menu Additional Material DAY and Time Display ModesSET the DAY and Time Main Menu DisplayLOADING, UNLOADING, Protecting the Tape Cassette LoadingWhen to Replace a Tape Table C. Tape Replacement by UseUnloading Preventing Accidental ErasureRecording Manual RecordingRecording Mode Recording Check FunctionAudio RECORDING/PLAYBACK Repeat RecordingTable E. Action When Tape End Is Reached by Setting Stop Rewind Repeat AlarmprotSeries Recording Remote Recording ONE-SHOT/INTERVAL RecordingSynchronous Recording Synchronous Recording SequenceTimer Recording Programming ProcedureHoliday SET UP Special DW SettingWhat if the Timer Recording Indicator Starts FLASHING? Overlapping ProgramsAlarm Recording Table G. Minimum Interval Between RecordingsProgramming for Alarm Recording Maintenance Recording After a Power FailurePower Loss List Viewing the Power Loss ListAlarm List Viewing the Alarm ListClearing the Alarm List ALL Menu Initialize ResetElapsed Time and Repeat Recording Times Display Elapsed TimeRepeat REC Times Playback Procedure PlaybackPlayback Mode Audio PlaybackEND of Tape Special Effects PlaybackShuttle Ring Direct Shuttle RingAdjusting the Picture During Playback Tracking Adjustment Adjusting Picture QualityVertical Vibration Adjustment Search Techniques Counter Memory StopSkip Search HOW to Count the Index Number Index SearchTime and Date Search Additional Functions and Features Using with a PC Assigning the RS-S32C SettingsCommands from a PC When Controlling only ONE VCRSending Commands Status or Error Code from Meaning When Controlling Multiple Vcrs Commands When Controlling Multiple VCRsVCR01, RC CR Commands and Responses Chart Commands Functions Status After Normal Explanation of StatusOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Testing Error CodesInitial System Testing Regular System TestingTroubleshooting SELF-DIAGNOSTIC Function and Warning DisplayTable J. Warning Display and Actions Fluorescent Monitor Cause Remedy To Turn Off DisplayBefore Calling for Service Symptom RemedyRecording Problems Specifications ElectricalVideo and Audio MechanicalVideo Audio Tape Mode 120/T-160 Mm/s Field Fields/s Table K. Tape Speed and Recording TimeIndex Pelco Manual C673M 2/01 Regulatory Notices Revision History