Pelco TLR3168 operation manual Time and Date Search

Page 56

TIME AND DATE SEARCH

You can find a picture recorded at a specific date and time.

1.Press the SEARCH button enough times to highlight TIME DATE SEARCH on the Search Function menu. The time and date search indicator (D) on the fluorescent display lights.

2.Turn the SHUTTLE ring right. The Time Date Search menu appears.

Turn the SHUTTLE ring left several times to exit the Time Date Search menu without searching.

3.Turn the JOG dial to set the digits for the hour you want to find next to TIME. Turn the SHUTTLE ring right.

4.Set the 10-minute and 1-digits in the same way.

5.Set the date using the JOG dial and SHUTTLE ring in the same manner.

6.Set the direction (forward or reverse) in which to search the tape using the JOG dial and SHUTTLE ring.

(When the desired part of the tape is not found in the selected direction, the VCR automatically searches in the opposite direction.)

7.Turn the SHUTTLE ring right to begin searching. When the recorded picture is found, it is shown in still mode.

8.To quit while searching, press STOP.

The VCR writes an index mark on the tape at each hour (1:00, 2:00, etc.) during recording. The time and date search cannot be resumed if the hour’s index mark (set in step 3) is not recorded on the tape. (For example, if the VCR recorded from 8:15 to 17:30 on the tape, only pictures between 9:00 and 17:30 can be found.)

The time and date search may not function correctly if you used a tape with poor recording quality or with alarm recordings in several recording modes. Also, it will not function with a tape recorded with other VCRs or with a tape recorded without setting the date and time.

56

Pelco Manual C673M (2/01)

Image 56
Contents TLR3168 Time-Lapse VCR Installation C673M 2/01 Contents Pelco Manual C673M 2/01 List of Illustrations List of TablesGeneral AvertissementSAFEGUARDS, WARNINGS, CAUTIONS, and Care Cleaning AccessoriesLightning/Power Surges When Not In UseUnpacking Instructions Introduction to TIME-LAPSE RecordersTLR3168 Features and Functions Additional Items Quick StartBasic Start Installation PRE-INSTALLATION CautionsSecuring the VCR Controls Monitor TipsInstallation Typical System SetupConnecting the VCR to a Multiplexer Connecting a VCR to a MultiplexerConnecting for Remote Recording Alarm Recording ConnectionConnecting for Series Recording Connecting for Synchronous Recording Connecting for External Time Clock AdjustmentTable A. RS-232C Protocol Connecting the VCR to a PCConnecting to a PC for Remote Control Cable Connections PLAY/REC Check ControlsFront Panel POSITION/VERTICAL Adjust buttons + Timer REC buttonEject button Search buttonFluorescent Display Timer Recording indicator Tape Remaining indicatorEmgcy emergency recording indicator LOCK/LOCK a indicatorCall OUT Mode OUTRear Panel Adjusting the Clock and Using the JOG and Shuttle Controls Using the JOG DialUsing the Shuttle Ring JOG and Shuttle ControlsAdjusting the Clock Adjusting to the Exact SecondProgramming General Programming InstructionsLanguage Selection Menu MenuProgram to Record Holiday SET UP Quick Guide to the Menu StructureDisplay Menu Display Mode Main MenuTIME/DATE Size Blue BackTimer Program START/ENDRecording SET UP Menu Setting Rear Terminal MenuWrngtape END Wrngremain Tape END Clock OUTREC Maintenance Menu First Time SET UP MenuRS-232C Menu Additional Material DAY and Time Display ModesSET the DAY and Time Main Menu DisplayLOADING, UNLOADING, Protecting the Tape Cassette LoadingWhen to Replace a Tape Table C. Tape Replacement by UseUnloading Preventing Accidental ErasureRecording Manual RecordingRecording Mode Recording Check FunctionAudio RECORDING/PLAYBACK Repeat RecordingSeries Recording Table E. Action When Tape End Is Reached by SettingStop Rewind Repeat Alarmprot Remote Recording ONE-SHOT/INTERVAL RecordingSynchronous Recording Synchronous Recording SequenceTimer Recording Programming ProcedureHoliday SET UP Special DW SettingWhat if the Timer Recording Indicator Starts FLASHING? Overlapping ProgramsAlarm Recording Table G. Minimum Interval Between RecordingsProgramming for Alarm Recording Maintenance Recording After a Power FailurePower Loss List Viewing the Power Loss ListAlarm List Viewing the Alarm ListClearing the Alarm List ALL Menu Initialize ResetRepeat REC Times Elapsed Time and Repeat Recording Times DisplayElapsed Time Playback Procedure PlaybackPlayback Mode Audio PlaybackEND of Tape Special Effects PlaybackShuttle Ring Direct Shuttle RingAdjusting the Picture During Playback Tracking Adjustment Adjusting Picture QualityVertical Vibration Adjustment Skip Search Search TechniquesCounter Memory Stop HOW to Count the Index Number Index SearchTime and Date Search Additional Functions and Features Using with a PC Assigning the RS-S32C SettingsSending Commands Status or Error Code from Meaning Commands from a PCWhen Controlling only ONE VCR When Controlling Multiple Vcrs Commands When Controlling Multiple VCRsVCR01, RC CR Commands and Responses Chart Commands Functions Status After Normal Explanation of StatusOn next SKP Small =WRNG, 1=WRNGTAPE END =OFF, 1=ON Testing Error CodesInitial System Testing Regular System TestingTroubleshooting SELF-DIAGNOSTIC Function and Warning DisplayTable J. Warning Display and Actions Fluorescent Monitor Cause Remedy To Turn Off DisplayBefore Calling for Service Symptom RemedyRecording Problems Specifications ElectricalVideo and Audio MechanicalVideo Audio Tape Mode 120/T-160 Mm/s Field Fields/s Table K. Tape Speed and Recording TimeIndex Pelco Manual C673M 2/01 Regulatory Notices Revision History