Pelco DX3016-120, DX3016-060, DX3009-060 manual Alarm Recording

Page 61

ALARM RECORDING

Alarm recording commences upon either of the following conditions:

An ALARM IN terminal is triggered by an alarm sensor

A camera detects motion

When there is an alarm:

1)The recorder switches to its preset recording intervals. Refer to Alarms in the Pro- gramming section for alarm settings.

2)An index signal is automatically stored in memory when alarm recording begins. Refer to the Playback section for reviewing alarm recordings using the index search.

3)If the unit receives a new alarm signal while in the alarm recording mode, the unit completes the alarm recording session initiated by the new signal.

4)If the unit receives an alarm signal at an ALARM IN terminal while settings are being made on the on-screen menus, the unit exits the menu screen and begins alarm re- cording.

5)The unit stores a data entry in an Alarm List of the time it receives the alarm signal. Refer to the Playback section for reviewing images from the Alarm List.

6)Regardless of the display mode, camera number buttons flash for those cameras making alarm recordings. The Alarm Recording indicator flashes on and off during alarm recording and stays on at the completion of alarm recording. If the DISPLAY MODE is set for values other than 5 or 6, an Alarm Recording number will automati- cally appear on-screen while the unit is running in alarm recording mode. The maxi- mum Alarm Recording number is 9999.

￿

At the end of alarm recording, the unit returns to the same recording intervals that were in effect before the alarm recording.

When in the alarm recording mode, the unit records for the entire alarm recording du- ration even if the end-time specified in a timer program has been exceeded. Alarm re- cording also continues as long as motion is detected within the active area established for motion detection. When motion stops, alarm recording continues for the time set in the A-REC DURATION setting.

There may be cases when the recorder’s built-in motion detection function does not operate properly due to the condition of the input video signal or other factors. There may be such operation errors when the recorder is connected to a system that uses the recorder’s detection function to send a warning signal.

If the recorder is programmed for pre-alarm recording, pre-alarm recordings are made of all cameras since it is not known which camera will have an alarm. After an ALARM IN terminal is triggered, however, only those cameras designated in the RECORD ALARM setting will make alarm recordings. This means that during playback the num- ber of cameras displayed may differ for pre-alarm and post-alarm recording.

60

Pelco Manual C681M-D (2/02)

Image 61
Contents Changing Password Entering Initial PasswordPassword Error Turning Password Lock On and OffUL Listed Contents Changing Playback Interval Fast FORWARD/REWIND Searching Using the Copy ButtonList of Illustrations Important Safeguards and Warnings Description OverviewGB PER Unit Timer REC button Power buttonModels Front Panel ControlsDET indicator Recording indicators Timer REC indicatorPRE Alarm REC indicator Multiplexer buttons Camera number buttonsLock indicator Mode indicators Access indicatorSET UP button Copy indicatorRear Panel Connectors RS-232C connector AC power socketAlarm in terminals Power on terminalCamera #1 InstallationSchematics for Alarm Input and Output Terminals Schematics for Input and Output Terminals HDD DVD-RAMIomega Z250S Adding a Hard Drives Adding or Removing a Copy or Archive DeviceRemoving a Hard Drives BOOT-UP DelayConfirming That a Device is Connected Programming SET UPMenu Tree, DX3009 Models Pelco Manual C681M-D 2/02 Menu Tree, DX3016 Models Menu Tree, DX3016 Models Pelco Manual C681M-D 2/02 Maximum Recording Fields Alarms Image QualityBASIC, STANDARD, MEDIUM, HIGH, Superior Define Group Setting Record Alarm Alarm Recording DurationALL, SEP PRE-ALARM RecordingOFF, SHORT, MEDIUM, Long Archive Pointer Reset DET SettingArchive Data Overwrite Auto Eject Audio RecordingKEY, WRNG, REMAIN, OFF BuzzerCapacity Remaining Call OUTHDD, ARC, None Data Clear Erase SelectionBackup Following a Power Failure FIFO/OVERWRITE Mode DX3016 Models OnlyHard Disk Drive HDD Full Hard Disk Drive HDD Repeat Playback IM-CHECK ModeInitialize Menus Mode OUTMotion Detection REC, PLAY, POWER, RemainLOW, LOWER, HIGHER, HIGH, MED Multiplexer Display Screen Switch Pattern DX3016 Models Only Four-Camera Split 4 SettingSplit 9 Screen Setting DX3016 Models Only Split 4 Screen Setting DX3016 Models OnlySplit 16 Screen Setting DX3016 Models Only Channel Title Displaying Camera Title and/or Number SequenceNONE, TITLE, CH. no Alarm DisplayCamera Title Power FailureRecord Image Quality Maximum Recording Fields Define Group Select Recording ModeRS-232C Communication Saving Menu Data Saving Menu SettingsRestoring Menu Data Time and Date Display Display Mode TCP/IP Setting DX3016 Models OnlyCharacter Size Clock Location Time and Date SettingTitle Timer Recording Repeat steps 8-10 for the ending time C, SKIP, ARC, PowerSetting for the prioritized Program #2 Motion Detection During a Timer Recording DX3016 Models Only Estimating Recording Time SAT OperationSPLIT/SEQUENCE Button Viewing CamerasDX3009 Models DX3009 Models Nine camerasRemote Viewing Zoom ButtonsRecording Basic Recording Alarm Recording Playback Basic Playback Timer Recording in the Programming sectionRegular Playback Mode Adjusting Playback SpeedFRAME-BY-FRAME Still Frame Playback Pause PlaybackFast FORWARD/REWIND Changing Playback IntervalSearching Index Search Skip Search Jump to Starting Point Alarm List SearchPlayback on Another Device Using the Archive ButtonBacking UP Data Using the Copy Button Auto-Eject at the Completion of BackupSimultaneous Recording and Backup Still-Frame Playback Copy ModeDX3016 Models Restoring Data from a Backup Device Information Elapsed Time Display Power Failure ListRecorded Period ResetScsi Devices Connected Audio recording time table DX3009 Recording Time TablesWithout Audio recording Audio recordingDX3009 Recording Time Tables Audio recording, Pre-Alarm Recording duration is set to Long Basic DX3016 Recording Time TablesAudio recording, recording duration is set to Long Without Audio recording, recording duration is set to ShortAudio recording, recording duration is set to Short Audio recording, recording duration is set to MediumCall OUT Description of problem Please consult the following TroubleshootingIs the Lock function or the Password Lock function Jpeg SpecificationsPCM Power OFF Power onAlarm OUT Power ON, Power OFF, Alarm IN, Clock ADJ, RECRegulatory Notices Warranty and Return Information