Pelco DX3016-060, DX3016-120 manual Auto-Eject at the Completion of Backup, Using the Copy Button

Page 69

Auto-Eject at the Completion of Backup

The archive medium will be automatically ejected under the following conditions:

When the archive medium becomes full during archive backup. Refer to Auto Eject in the Programming section.

When the archive medium becomes full during timer backup. Refer to Auto Eject in the Pro- gramming section.

When the ARCHIVE button is pressed again, after operation was started with the ARCHIVE button.

When a recording malfunction, medium error, or system error occurs during backup opera- tion.

USING THE COPY BUTTON

NOTE: If you use the COPY button, the peripheral recording device must be assigned to SCSI ID number 5.

1.Make sure that the peripheral recording device is connected and set correctly.

2.Turn on the power of the peripheral recording device.

3.Turn on the power of the recorder.

4.Insert a copying medium into the archive device or copy device.

5.Press the COPY button. The Copy Selection menu appears.

6.Make sure that the cursor is next to COPY DIRECTION, and then turn the SHUTTLE ring to the right. The option starts flashing.

7.Use the JOG dial to choose copy direction (HDD to COPY), and then turn the SHUTTLE ring to the right. The option stops flashing.

8.Turn the JOG dial to move the cursor to OVERWRITE, and then turn the SHUTTLE ring to the right. The option starts flashing.

9.Turn the JOG dial to select ON or OFF, and then turn the SHUTTLE ring to the right. The option stops flashing.

ON: Copying starts at beginning of the medium, overwriting previously recorded data.

OFF: Copying starts at the end of the recorded part of the medium.

10.Turn the JOG dial to move the cursor next to TRANSFER PERIOD, and then turn the SHUTTLE ring to the right. The option starts flashing.

11.Turn the JOG dial to select MAN or S/E, and then turn the SHUTTLE ring to the right. The option stops flashing.

MAN: Set the starting and ending times for copying in the next step.

S/E: Copy all data from the device which is recognized as a device to copy from.

12.Set the starting and ending times.

If S/E was selected in the previous step, the starting and ending times of the data re- corded on the hard disk are displayed. There may be instances where it takes time for the peripheral device to collect the copy starting and ending times from the main unit. When the times are displayed, press the COPY button to enter the copy range auto- matically. This does not mean, however, that the copy function has been started.

If MAN was selected, the recorder will execute the copy function at a range slightly larger than the starting and ending settings.

a. Turn the JOG dial to move the cursor to the start time.

68

Pelco Manual C681M-D (2/02)

Image 69
Contents Changing Password Entering Initial PasswordPassword Error Turning Password Lock On and OffUL Listed Contents Changing Playback Interval Fast FORWARD/REWIND Searching Using the Copy ButtonList of Illustrations Important Safeguards and Warnings Overview DescriptionGB PER Unit Timer REC button Power buttonModels Front Panel ControlsDET indicator Recording indicators Timer REC indicatorPRE Alarm REC indicator Multiplexer buttons Camera number buttonsLock indicator Mode indicators Access indicatorSET UP button Copy indicatorRear Panel Connectors RS-232C connector AC power socketAlarm in terminals Power on terminalCamera #1 InstallationSchematics for Alarm Input and Output Terminals Schematics for Input and Output Terminals DVD-RAM HDDIomega Z250S Adding a Hard Drives Adding or Removing a Copy or Archive DeviceBOOT-UP Delay Removing a Hard DrivesConfirming That a Device is Connected Programming SET UPMenu Tree, DX3009 Models Pelco Manual C681M-D 2/02 Menu Tree, DX3016 Models Menu Tree, DX3016 Models Pelco Manual C681M-D 2/02 Alarms Image Quality Maximum Recording FieldsBASIC, STANDARD, MEDIUM, HIGH, Superior Define Group Setting Record Alarm Alarm Recording DurationPRE-ALARM Recording ALL, SEPOFF, SHORT, MEDIUM, Long DET Setting Archive Pointer ResetArchive Data Overwrite Auto Eject Audio RecordingKEY, WRNG, REMAIN, OFF BuzzerCapacity Remaining Call OUTHDD, ARC, None Data Clear Erase SelectionBackup Following a Power Failure FIFO/OVERWRITE Mode DX3016 Models OnlyHard Disk Drive HDD Full Hard Disk Drive HDD Repeat Playback IM-CHECK ModeInitialize Menus Mode OUTMotion Detection REC, PLAY, POWER, RemainLOW, LOWER, HIGHER, HIGH, MED Multiplexer Display Screen Switch Pattern DX3016 Models Only Four-Camera Split 4 SettingSplit 9 Screen Setting DX3016 Models Only Split 4 Screen Setting DX3016 Models OnlySplit 16 Screen Setting DX3016 Models Only Channel Title Displaying Camera Title and/or Number SequenceNONE, TITLE, CH. no Alarm DisplayPower Failure Camera TitleRecord Image Quality Maximum Recording Fields Define Group Select Recording ModeRS-232C Communication Saving Menu Settings Saving Menu DataRestoring Menu Data Time and Date Display Display Mode TCP/IP Setting DX3016 Models OnlyCharacter Size Time and Date Setting Clock LocationTitle Timer Recording Repeat steps 8-10 for the ending time C, SKIP, ARC, PowerSetting for the prioritized Program #2 Motion Detection During a Timer Recording DX3016 Models Only Estimating Recording Time SAT OperationSPLIT/SEQUENCE Button Viewing CamerasDX3009 Models DX3009 Models Nine camerasZoom Buttons Remote ViewingRecording Basic Recording Alarm Recording Playback Basic Playback Timer Recording in the Programming sectionRegular Playback Mode Adjusting Playback SpeedFRAME-BY-FRAME Still Frame Playback Pause PlaybackChanging Playback Interval Fast FORWARD/REWINDSearching Index Search Skip Search Jump to Starting Point Alarm List SearchUsing the Archive Button Playback on Another DeviceBacking UP Data Using the Copy Button Auto-Eject at the Completion of BackupStill-Frame Playback Copy Mode Simultaneous Recording and BackupDX3016 Models Restoring Data from a Backup Device Information Elapsed Time Display Power Failure ListReset Recorded PeriodScsi Devices Connected Audio recording time table DX3009 Recording Time TablesWithout Audio recording Audio recordingDX3009 Recording Time Tables Audio recording, Pre-Alarm Recording duration is set to Long Basic DX3016 Recording Time TablesAudio recording, recording duration is set to Long Without Audio recording, recording duration is set to ShortAudio recording, recording duration is set to Short Audio recording, recording duration is set to MediumCall OUT Description of problem Please consult the following TroubleshootingIs the Lock function or the Password Lock function Specifications JpegPCM Power OFF Power onAlarm OUT Power ON, Power OFF, Alarm IN, Clock ADJ, RECRegulatory Notices Warranty and Return Information