Sterling BF3-600 specifications Digital Dosing unit parameter setup

Page 60

Digital Dosing unit parameter setup 7-14


		Bison - Black motor				Bauer - Blue motor			Comments
Parameter
	RPM	2	6	12	38	6.4	11.5	35.5
7		65000	25200	14103	4387	11739	6600	2135	These values refer to the pulses of the encoder
8
8			0.5				0.7		Nominal motor current
9		Ext		Inj		Ext		Inj
		1040		16		1040		16	(see separate calculation sheet for parameter #9)
10
10		0					1		Factory set, do not change

11		Ext		Inj		Ext		Inj

		50		50		50		50	Ext = minimum input frequency w/follower only
12		Ext		Inj		Ext		Inj	Inj = Minimum # of machine cycles per dosing
12		Ext		Inj		Ext		Inj
		10		5.56		10		5.56	Ext = Span factor (sf) calculated using: sf=1000/rpm@10vdc
13		Ext		Inj		Ext		Inj	sf = 1000/rpm @20ma
13		Ext		Inj		Ext		Inj

		0		0		0		0	Communication address used with Euromap 17 (use 1instead of 0)
14		Ext		Inj		Ext		Inj
		0		0		0		0	For use with Mico mix hopper (use 1 instead of 0)

59

Image 60

Contents SDD Digital Dosing Units Parts and Service Department Table of Contents Introduction Station Digital Dosing UnitI C K A R T G E S V E U E R D E R Controller Touch KeypadKeys and Symbols Symbols Recipe Setup For Injection Molding Quick Start-upUnpacking MountingRecipe Setup For Extrusion CalibrationI C K A R T G E S V E U E R D E R Initial Installation And Operation Initial InstallationElectrical diagram of connections Electrical DiagramDiagram of frequency inputs Initial OperationInjection Molding Recipe Input Injection MoldingStep Step Step Step Operation-Injection Molding Extrusion Constant Recipe Input Extrusion ConstantStep Step Operation -Extrusion Constant Extrusion Proportional Recipe Input Extrusion ProportionalStep Operation -Extrusion Proportional Calibration Determining the Calibration Weight Repeat steps 3 and 4 four 4 more times Digital Dosing Units Advanced Operations/ Control Functions Recipe Storage And RecallRecipe Storage Recipe Recall Acknowledging Alarms Clearing The TotalizerOptional Equipment Alarms Level ProbesMixer Euromap E17 InterfaceMaintenance Maintenance IntervalsRemoving the Scraper Removing the scraperCleaning the Digital Dosing Dosing Station Installing the scraperDismantling the Dosing Station Installing the Dosing Station Installing the Dosing Disc Removing the Dosing DiscInstalling Different Types of Dosing Discs Removing/Replacing the Scraper in the DT Dosing StationCleaning the DT Dosing Station Exchangeable Stations Replacing FusesSee Appendix D on page 61 for fuse part numbers Appendix a Troubleshooting General Troubleshooting Unit Will Not OperateMalfunctions or Errors Error Codes Error Codes Determining the Software Setup Factor Recipe FormulasInjection Molding ExtrusionRecipe Limitations Extrusion Appendix B Basic Parameter Settings Extrusion ModeMax. input frequency = Hz Determining the Configuration Value Extrusion Constant or ProportionalProbe Digital Dosing Units Basic Parameter Settings Digital Dosing Units Digital Dosing Units Disc Dosing Factor Disc Guide D30-051725 DT30-102025 DP30 Specification Sheet Disc Dosing Factor TableDigital Dosing unit parameter setup Page Station 1 Digital Dosing Unit Station 2 Digital Dosing Unit Side View TOP ViewDosing Unit Electrical Schematic Chart Appendix D Spare Parts List Dosing Disc/Shear Order NumbersPage Service Department Technical AssistanceParts Department Sales Department