Sanyo VCC-6974 Using the Menu Screen, Using the Cursor button, Switching to sub-menu screens

Page 14

USING THE MENU SCREEN

This unit is set at the factory so that it can be used with a DC type auto-iris lens (sold separately). Therefore, under normal conditions, additional settings or adjustments are not necessary. Depending on the conditions of use, if settings or adjustments are required they can be done from the “MAIN MENU” setting screen.

1Press the SET button for about 3 seconds. The MAIN MENU screen will be displayed.

2Using the CURSOR button

1Press the CURSOR (l) button to move the cursor down. When the cursor reaches the bottom of the screen, it goes back up to the top of the screen.

2Press the CURSOR (j) button to move the cursor up. When the cursor reaches the top of the screen, it goes back down to the bottom of the screen.

3Press the CURSOR (c) button to move the cursor to the right. This button is also used to change ON/OFF settings etc.

4Press the CURSOR (d) button to move the cursor to the left. This button is also used to change ON/OFF settings etc.

Switching to sub-menu screens

Press the CURSOR (j, l, d or c) button until an item with a “c” next to it is flashing, then press the SET button.

Switching to the MAIN MENU screen

Press the CURSOR (j or l) button to select BACK (it will flash), then press the SET button.

3When finished:

Press the CURSOR (l) button to select END (it will flash), then press the SET button. The display will return to the normal monitor screen.

(Default setting)

SET

		MAIN MENU
		LANGUAGE	SET	p
		CAMERA ID	OFF
		SYNC	INT
		IRIS	AI	p
2		WHITE BALANCE	ATW	p
2		SHUTTER	OFF
CURSOR		MOTION	OFF
4	3	OPTION	SET	p
4	3	MENU	END
		MENU	END
1
		(Example)
CURSOR	SET	LANGUAGE
	SET	LANGUAGE
		LANGUAGE	ENGLISH
		LANGUE	FRENCH
		IDIOMA	SPANISH
CURSOR	SET
	SET
		MENU	BACK
CURSOR	SET
	SET
		MENU	END

English 13

Image 14

Contents About this manual Propos de ce manuelContents FeaturesPour la clientèle canadienne Information to UserFor the customers in Canada Precautions Alarm output terminal ALARM, C, a Power indicator PowerVideo output connector Video OUT BNC type Parts NamesMenu setting button SET Camera setup section under the coverLens iris output connector Lens Cursor button CursorLens mount cap DC type auto-iris lens If using a Video type auto-iris lensConcerning AUTO-IRIS Lenses Video type auto-iris lensMount type lens Mounting the LensRemove the lens mount cap from the camera Rewiring the lens cable in the lens iris plug Flange-back adjustmentCoaxial cable type and maximum length ConnectionsBasic connection for monitoring or recording Connection to a multiplexer RS-485 terminal connectionsConnection to a VCR Preset will return to the zoom pan, tilt center position About the Alarm output terminalRemote controller circuit connections Switching to sub-menu screens Using the Menu ScreenUsing the Cursor button Switching to the Main Menu screenUsing the Menu Screen Language setting Then press the SET buttonDetermining the start position for character input Camera ID settingExample To set the camera ID to BN1 Changing the camera ID to a new IDDisplay will return to the Camera ID Setting screen External sync VBS Sync settingsInternal synchronization INT Power supply synchronization setting L L External sync setting VBS Menu Back END Lens Type setting Iris settingAI Auto Iris mode setting Adjust the Iris Level setting DC type lens only BLC settingAI/BLCMULTI BLC/EVAL 5-section photometry mode setting BLC Window Weighting screen will be displayedWeighting Returning the values to the default settingsPress the Cursor l, then d or c button until EI Sense UP settingEI Electronic Iris mode setting Manual white balance MWB White Balance settingAutomatic color temperature tracking setting ATW Masking setting White BALANCE/ATWMASKINGMenu Back END Push-lock white balance adjustment AWC Press and hold the SET buttonManual white balance setting MWB Long exposure mode Long Electronic Shutter settingShort mode Short For Short mode For Long mode When Motion is set to ON, Long mode cannot be selectedExample Motion settingIris Sense UP mode has been set. Refer to Sensitivity setting function Sensitivity Size setting function SizeMask area setting function Masking Alarm interval setting function IntervalDirection setting Üü, íí, óó, ññSize setting V vertical value is flashing, then press the Cursor c buttonMotion Size display table Returning to the default setting MOTION/MASKING Menu Back END Maximum Sensitivity settingThis sets the movement amplitude of subjects on the screen Zoom setting MOTION/ZOOM, IntervalInterval setting Alarm Sign settingChecking the detected movements set by the Motion item Image is zoomed in when a movement is detectedCamera ID flashes on-screen when a movement is detected Active Move Differ Option settings Aperture setting AGC setting Gamma settingFor FIX mode PanningReturning to the default settings OPTION/FIXI TiltFor VAR mode ZoomingOPTION/VAR ZOOM, Tilt Mirror setting RS-485 settingAbout SW No Address settingTerminate setting Initial setting SET buttonOperations Using the System Controller Operations using the camera Menu screensIris level operations Operations using the camera command Camera buttonElectronic zoom White balance and AWC-LOCK settings Setting the Sense UP and electronic shutterBacklight correction settings Menu Display 4321Menu Display Picture is not clear TroubleshootingNo picture on the monitor screen Specifications CameraAccessories Dimensions mmExclusions