Sanyo VCC-6974 instruction manual Checking the detected movements set by the Motion item

Page 47

USING THE MENU SCREEN

MOTION/EXAMPLE

Motion detector setting example

After the camera has been connected to the peripheral devices (VCR, multiplexer, etc.) set the MOTION item to send an alarm trigger to the peripheral devices when the set movement parameters are met.

Checking the detected movements set by the MOTION item

If the MOTION item settings are not made properly, the desired results will not be obtained. To test for correct detection, please proceed as follows.

There are two setting checking methods, using the ADJUSTMENT FOR MOTION screen ZOOM or

ALARM SIGN.

A) The image is zoomed in when a movement is detected

Set the ZOOM item to 5S. When the motion detector senses a movement from a subject on the screen, the image is zoomed in.

B) The camera ID flashes on-screen when a movement is detected

Set the ALARM SIGN item to ON, then exit the menu screen. When the motion detector senses a movement from a subject on the screen, the camera ID is displayed on-screen.

Note: The camera ID will not be displayed while a menu is displayed on-screen.

CAMERA 1

46 English

Image 47

Contents Propos de ce manuel About this manualFeatures ContentsPour la clientèle canadienne Information to UserFor the customers in Canada Precautions Parts Names Power indicator PowerVideo output connector Video OUT BNC type Alarm output terminal ALARM, C, aCursor button Cursor Camera setup section under the coverLens iris output connector Lens Menu setting button SETLens mount cap Video type auto-iris lens If using a Video type auto-iris lensConcerning AUTO-IRIS Lenses DC type auto-iris lensMount type lens Mounting the LensRemove the lens mount cap from the camera Flange-back adjustment Rewiring the lens cable in the lens iris plugCoaxial cable type and maximum length ConnectionsBasic connection for monitoring or recording Connection to a multiplexer RS-485 terminal connectionsConnection to a VCR Preset will return to the zoom pan, tilt center position About the Alarm output terminalRemote controller circuit connections Switching to the Main Menu screen Using the Menu ScreenUsing the Cursor button Switching to sub-menu screensUsing the Menu Screen Then press the SET button Language settingChanging the camera ID to a new ID Camera ID settingExample To set the camera ID to BN1 Determining the start position for character inputDisplay will return to the Camera ID Setting screen External sync VBS Sync settingsInternal synchronization INT Power supply synchronization setting L L External sync setting VBS Menu Back END Lens Type setting Iris settingAI Auto Iris mode setting BLC setting Adjust the Iris Level setting DC type lens onlyAI/BLCMULTI BLC Window Weighting screen will be displayed BLC/EVAL 5-section photometry mode settingReturning the values to the default settings WeightingPress the Cursor l, then d or c button until EI Sense UP settingEI Electronic Iris mode setting Manual white balance MWB White Balance settingAutomatic color temperature tracking setting ATW White BALANCE/ATWMASKING Masking settingMenu Back END Press and hold the SET button Push-lock white balance adjustment AWCManual white balance setting MWB Long exposure mode Long Electronic Shutter settingShort mode Short For Short mode When Motion is set to ON, Long mode cannot be selected For Long modeExample Motion settingIris Sense UP mode has been set. Refer to Alarm interval setting function Interval Size setting function SizeMask area setting function Masking Sensitivity setting function SensitivityÜü, íí, óó, ññ Direction settingV vertical value is flashing, then press the Cursor c button Size settingMotion Size display table Returning to the default setting MOTION/MASKING Menu Back END Maximum Sensitivity setting This sets the movement amplitude of subjects on the screen MOTION/ZOOM, Interval Zoom settingAlarm Sign setting Interval settingChecking the detected movements set by the Motion item Image is zoomed in when a movement is detectedCamera ID flashes on-screen when a movement is detected Active Move Differ Option settings Aperture setting Gamma setting AGC settingPanning For FIX modeOPTION/FIXI Tilt Returning to the default settingsZooming For VAR modeOPTION/VAR ZOOM, Tilt RS-485 setting Mirror settingAbout SW No Address settingTerminate setting SET button Initial settingOperations using the camera Menu screens Operations Using the System ControllerIris level operations Operations using the camera command Camera buttonElectronic zoom White balance and AWC-LOCK settings Setting the Sense UP and electronic shutterBacklight correction settings 4321 Menu DisplayMenu Display Picture is not clear TroubleshootingNo picture on the monitor screen Camera SpecificationsDimensions mm AccessoriesExclusions