Sanyo VCC-6974 instruction manual Motion/Masking

Page 42

USING THE MENU SCREEN

MOTION/MASKING

CMASKING setting

1 Press the CURSOR (l, then d or c) button to set MASKING to “ON” (the setting will flash), then press the SET button.

The MOTION MASKING screen will be displayed, and the mask cursor will flash in the top-left corner of the screen.

2Press the CURSOR (d, c, j or l) button to move the mask cursor to the place where movement is not to be detected, then press the SET button.

The position of the mask cursor will be fixed, and the area will increase each time the CURSOR button is pressed. Press the CURSOR button repeatedly to set the masking area. Masks can be applied to a maximum of 64 separate sections (8 x 8).

Note: If you apply a mask to a wrong area by mistake, press the SET button once more to clear the mask.

3When the mask has been applied, press the CURSOR (l) button to move the mask cursor to the bottom edge of the screen, and continue pressing the CURSOR button for about 3 seconds.

☞Returning to the default setting

Press the CURSOR (l, then d or c) button to change the PRESET setting to ON, then press the SET button.

CURSOR SET ADJUSTMENT FOR MOTION

		DIRECTION	OFF
		SIZE	SET	p
		MASKING	ON	p
CURSOR	SET	MOTION MASKING
	SET

CONT PRESS(ñ)

(Example)

English 41

Image 42

Contents About this manual Propos de ce manuelContents FeaturesInformation to User For the customers in CanadaPour la clientèle canadienne Precautions Alarm output terminal ALARM, C, a Power indicator PowerVideo output connector Video OUT BNC type Parts NamesMenu setting button SET Camera setup section under the coverLens iris output connector Lens Cursor button CursorLens mount cap DC type auto-iris lens If using a Video type auto-iris lensConcerning AUTO-IRIS Lenses Video type auto-iris lensMounting the Lens Remove the lens mount cap from the cameraMount type lens Rewiring the lens cable in the lens iris plug Flange-back adjustmentConnections Basic connection for monitoring or recordingCoaxial cable type and maximum length RS-485 terminal connections Connection to a VCRConnection to a multiplexer About the Alarm output terminal Remote controller circuit connectionsPreset will return to the zoom pan, tilt center position Switching to sub-menu screens Using the Menu ScreenUsing the Cursor button Switching to the Main Menu screenUsing the Menu Screen Language setting Then press the SET buttonDetermining the start position for character input Camera ID settingExample To set the camera ID to BN1 Changing the camera ID to a new IDDisplay will return to the Camera ID Setting screen Sync settings Internal synchronization INTExternal sync VBS Power supply synchronization setting L L External sync setting VBS Menu Back END Iris setting AI Auto Iris mode settingLens Type setting Adjust the Iris Level setting DC type lens only BLC settingAI/BLCMULTI BLC/EVAL 5-section photometry mode setting BLC Window Weighting screen will be displayedWeighting Returning the values to the default settingsSense UP setting EI Electronic Iris mode settingPress the Cursor l, then d or c button until EI White Balance setting Automatic color temperature tracking setting ATWManual white balance MWB Masking setting White BALANCE/ATWMASKINGMenu Back END Push-lock white balance adjustment AWC Press and hold the SET buttonManual white balance setting MWB Electronic Shutter setting Short mode ShortLong exposure mode Long For Short mode For Long mode When Motion is set to ON, Long mode cannot be selectedMotion setting Iris Sense UP mode has been set. Refer toExample Sensitivity setting function Sensitivity Size setting function SizeMask area setting function Masking Alarm interval setting function Interval Direction setting Üü, íí, óó, ññSize setting V vertical value is flashing, then press the Cursor c buttonMotion Size display table Returning to the default setting MOTION/MASKING Menu Back END Sensitivity setting This sets the movement amplitude of subjects on the screenMaximum Zoom setting MOTION/ZOOM, IntervalInterval setting Alarm Sign settingImage is zoomed in when a movement is detected Camera ID flashes on-screen when a movement is detectedChecking the detected movements set by the Motion item Active Move Differ Option settings Aperture setting AGC setting Gamma settingFor FIX mode PanningReturning to the default settings OPTION/FIXI TiltFor VAR mode ZoomingOPTION/VAR ZOOM, Tilt Mirror setting RS-485 settingAddress setting Terminate settingAbout SW No Initial setting SET buttonOperations Using the System Controller Operations using the camera Menu screensOperations using the camera command Camera button Electronic zoomIris level operations Setting the Sense UP and electronic shutter Backlight correction settingsWhite balance and AWC-LOCK settings Menu Display 4321Menu Display Troubleshooting No picture on the monitor screenPicture is not clear Specifications CameraAccessories Dimensions mmExclusions