Sony HD 3CCD Transmitting Audio Signals Using the BRU-H700, CCFC-M100HG BRBK-H700 HD

Page 15

Transmitting Audio Signals Using the BRU-H700

This system allows you:

•To operate the camera remotely from a distance up to 1,000m (3,281 feet)

•To perform pan/tilt and zoom operations comfortably using the joystick

•To transmit the video signal and control signal of the camera, and the audio signal input to the BRBK-H700 Optical Multiplex Card to a distant place using the Optical Fiber Cable

System configuration

			HD video monitor	Speakers
			HD video monitor
	Microphone
BRC-H700		Microphone amplifier
		Microphone amplifier
				Audio
				amplifier
		CCFC-M100HG
	BRBK-H700 HD	Optical Fiber	BRU-H700 HD
		Cable	BRU-H700 HD
		Cable	Optical Multiplex
	Optical Multiplex		Optical Multiplex
	Optical Multiplex		Unit
	Card		Unit
	Card
Video signal
Audio line signal			RM-BR300 Remote Control Unit
Remote control (VISCA) signal
,	Signal flow

Overview

System Configuration

Image 15

Contents HD 3CCD Color Video Camera Pour les utilisateurs au Canada Owner’s RecordFor customers in the U.S.A For the customers in CanadaTable of Contents Appendix Installation and ConnectionsTypical CCD Phenomena PrecautionsVisca camera protocol supported FeaturesBuilt-in interface card slot Long-distance image transmission and pan/tilt/zoom controlExternal video sync function Supplied Components and AccessoriesMounted circuit board using lead-free solder System ComponentsBRU-H700 HD Optical Multiplex Unit Remote commanderRM-BR300 Remote Control Unit Optional ProductsHFBK-TS1 HDV Interface Board Video Switcher commercially availableHFBK-SD1 SD Interface Board HFBK-HD1 HD Interface BoardSystem Configuration System configurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG CCFC-M100HG BRBK-H700 HD Transmitting Audio Signals Using the BRU-H700HFBK-TS1 HDV HD video monitor Microphone Rear Location and Function of PartsCamera FrontBottom Setting of the Bottom switchesRemote Commander supplied Mode button RM-BR300 Remote Control Unit not suppliedInstalling batteries Lock button and indicatorWhen the menu of the camera is displayed When the menu of the camera is not displayedTALLY/CONTACT connector Mode selectorVisca RS-232C connector Visca RS-422 connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-HD1 HD Interface Board not supplied HFBK-SD1 SD Interface Board not suppliedHFBK-XG1 XGA Interface Board not supplied HFBK-TS1 HDV Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied Setting Menus About On-Screen MenusMain Menu To return to the normal display Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the main menu4,5 Exposure Menu Back LightSpot Light Color Menu Using the ND FilterWhite Balance white balance mode When ONE Push is selectedPicture Menu Color BAR Black and white modeMode focus mode Focus MenuRamp Curve Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP PAN Tilt Zoom MenuSystem Menu Analog OUTSync Master ADD Sync Status MenuDown Converter Menu SUB OUT1Sync HD-SDI MenuPC-OUTPUT Menu Sync VDHDV Menu Audio DelayTurning on the Power Pan/Tilt and Zoom OperationPanning and Tilting Operating Multiple Cameras with the Remote Commander ZoomingIf the Standby lamp of the camera flashes To focus the camera on a subject automatically Adjusting the CameraFocusing on a Subject Shooting with Back LightingTo cancel the preset memory To recall the stored settingsTo illuminate the panel of the Remote Control Unit Operating Multiple CamerasTo assign camera addresses automatically To assign camera addresses manually Direction REV 1STD PAN-TILT ResetTurn the dial on the upper part of the joystick To adjust the white balance manually Adjusting the White BalanceOne-push auto focusing during manual focus adjustment To adjust the white balance automaticallyAdjusting the Brightness Functions of the Value and Bright controlsFunctions of the R and B controls To select positions 9 to Storing Camera SettingsSetting the Speed of the Camera Moving to a Preset Position To remove the cable cover InstallationRemoving/Attaching the Cable Cover Attaching an Interface BoardTo attach the camera to a tripod Installing the CameraTo install the camera on a desk To remove the interface boardInstalling the Camera on the Ceiling Before installationInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connecting to an AC Outlet ConnectionsTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a VTR Equipped with SDI Input ConnectorConnecting the BRU-H700 HD Optical Multiplex Unit Connecting a ComputerCable Second BRC Connecting a Video SwitcherConnecting a Sync Signal Generator To connect multiple cameras to the HD sync signal generatorTo connect a single camera Sync To connect multiple cameras to the SD sync signal generatorMessages for the BRC-H700 camera Indicators on the BRC-H700 cameraError messages for the BRU-H700 HD Optical Multiplex Unit List of MessagesSymptom Cause Remedy TroubleshootingSymptom Cause Remedy Speed Menu ConfigurationSTD RGB Presetting menu items Presetting ItemsSUB OUT ADD Sync IMG Size System SpecificationsInput/output connectors Supplied accessoriesTop Side DimensionsBRC-H700 Video Camera Ceiling Bracket BRM-BR300 Remote Control Unit Top Front Side BRU-H700 HD Optical Multiplex Unit TopPin Assignments Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-232C OUT connector mini DIN 8-pin, femaleBRU-H700 HD Optical Multiplex Unit optional RM-BR300 Remote Control Unit optionalVisca RS-232C OUT connector mini DIN 8-pin FemalePin Wiring Diagram of Visca RS-422 Connection Third to Seventh BRC-H700 or BRU-H700Second BRC-H700 or BRU-H700 To remove the connector plug Using the Visca RS-422 Connector Plug