Sony HD 3CCD Specifications, System, Input/output connectors, General, Supplied accessories

Page 72

Appendix

Specifications

System

Video signal

1080/59.94i, 1080/50i (switched with

 

the BOTTOM switch)

Synchronization

 

 

Internal/external synchronization,

 

automatically switched

Image device

1/3 type (6 mm), 3CCD Interline

 

transfer type

 

Total picture elements: Approx.

 

1,120,000 pixels

 

Effective picture elements: Approx.

 

1,020,000 pixels

Lens

Carl Zeiss Vario-SonnarT*

 

12× (optical), 4× (digital)

 

Filter diameter: 72 mm (Wide and

 

tele conversion lenses cannot be

 

attached.)

 

f = 4.5 – 54 mm, F1.6 – F2.8

 

F = 32.5 mm – 390 mm (equivalent

 

to the focal length of a 35-mm

 

camera)

Minimum object distance

800mm (11 7/8 inches) (TELE end) Minimum illumination

6lux (F1.6) with 50 IRE (WIDE end)

Shutter speed

1/59.94 (1/50) to 1/10,000 sec.

Video S/N

50 dB

Pan/tilt action

Horizontal: ±170 degrees

Maximum panning speed: 60 degrees/sec.

Minimum panning speed: 0.25 degrees/sec.

Vertical: +90 degrees, -30 degrees Maximum tilting speed: 60 degrees/ sec.

Minimum tilting speed: 0.25 degrees/sec.

Input/output connectors

Video output

D-sub 15-pin

RGB: 0.7Vp-p (no sync, at 75-ohm termination)

1Vp-p (±0.3V, tri-level sync, at 75-ohm termination) Component :

Y:1Vp-p (±0.3V, tri-level sync, at 75-ohm termination)

Pb/Pr: ±350 mVp-p, 75-ohm terminated

HD/VD Sync: 1Vp-p, 75-ohm terminated

Tri-level Sync: ±300 mVp-p, 75- ohm terminated

External sync input

EXT SYNC IN: BNC type Control input/output

VISCA RS-232C IN: Mini DIN 8-pin type

VISCA RS-232C OUT: Mini DIN 8- pin type

VISCA RS-422: 9-pin type Control signal format

9600 bps/38400 bps Data: 8 bit

Stop bit: 1

Power connector

JEITA type4 (DC IN 12V)

General

Input voltage 12 V DC (10.8 to 13.2 V DC) Current consumption

2.0A max. (at 12 V DC), 24 W without optional interface board

Operating temperature

0ºC to 40ºC (32ºF to 104ºF) Storage temperature

–20ºC to +60ºC (-4ºF to 140ºF)

Dimensions Video camera: ø207 × 315.8 mm (ø8 1/4 × 12 1/2 inches) (diameter/h) (excluding protruding parts)

Remote Commander: 56 × 26 × 210

mm(2 1/4 × 1 1/16 × 8 3/8 inches) (w/

h/d)

Mass

Video camera: Approx. 4.5 kg (9 lb 15

 

oz)

Remote Commander: 110 g (3.9 oz) Installation angle

Less than ±15 degrees to the horizontal surface

Supplied accessories

AC power adaptor MPA-AC1 (Sony) (100 V AC, 50/60 Hz) (1)

AC power cord (1) Remote Commander (1) Ceiling bracket (A) (1) Ceiling bracket (B) (1) Wire rope (1)

Screws (3M3 × 8) (7)

Screw (3M4 × 8) (1) RS-422 connector plug (1) Operating Instructions (1)

Design and specifications are subject to change without notice.

72

Specifications

Page 71 Page 73
Image 72
Page 71 Page 73
Contents HD 3CCD Color Video Camera Owner’s Record For customers in the U.S.AFor the customers in Canada Pour les utilisateurs au CanadaTable of Contents Installation and Connections AppendixPrecautions Typical CCD PhenomenaFeatures Built-in interface card slotLong-distance image transmission and pan/tilt/zoom control Visca camera protocol supportedSupplied Components and Accessories Mounted circuit board using lead-free solderSystem Components External video sync functionRemote commander RM-BR300 Remote Control UnitOptional Products BRU-H700 HD Optical Multiplex UnitVideo Switcher commercially available HFBK-SD1 SD Interface BoardHFBK-HD1 HD Interface Board HFBK-TS1 HDV Interface BoardSystem Configuration System configurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG Transmitting Audio Signals Using the BRU-H700 CCFC-M100HG BRBK-H700 HDHFBK-TS1 HDV HD video monitor Microphone Location and Function of Parts CameraFront RearSetting of the Bottom switches BottomRemote Commander supplied RM-BR300 Remote Control Unit not supplied Installing batteriesLock button and indicator Mode buttonWhen the menu of the camera is not displayed When the menu of the camera is displayedMode selector Visca RS-232C connectorVisca RS-422 connector TALLY/CONTACT connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-SD1 SD Interface Board not supplied HFBK-HD1 HD Interface Board not suppliedHFBK-XG1 XGA Interface Board not supplied HFBK-TS1 HDV Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied Setting Menus About On-Screen MenusMain Menu Menu Operation Using the Supplied Remote Commander Operation Through MenusTo return to the main menu To return to the normal display4,5 Exposure Menu Back LightSpot Light Using the ND Filter White Balance white balance modeWhen ONE Push is selected Color MenuPicture Menu Black and white mode Mode focus modeFocus Menu Color BARSetting range of PAN LEFT/PAN Right Setting range of Tilt DOWN/TILT UPPAN Tilt Zoom Menu Ramp CurveSystem Menu Analog OUTSync Master Status Menu Down Converter MenuSUB OUT1 ADD SyncHD-SDI Menu PC-OUTPUT MenuSync VD SyncAudio Delay HDV MenuTurning on the Power Pan/Tilt and Zoom OperationPanning and Tilting Operating Multiple Cameras with the Remote Commander ZoomingIf the Standby lamp of the camera flashes Adjusting the Camera Focusing on a SubjectShooting with Back Lighting To focus the camera on a subject automaticallyTo recall the stored settings To cancel the preset memoryTo illuminate the panel of the Remote Control Unit Operating Multiple CamerasTo assign camera addresses automatically Direction REV 1STD PAN-TILT Reset To assign camera addresses manuallyTurn the dial on the upper part of the joystick Adjusting the White Balance One-push auto focusing during manual focus adjustmentTo adjust the white balance automatically To adjust the white balance manuallyAdjusting the Brightness Functions of the Value and Bright controlsFunctions of the R and B controls Storing Camera Settings To select positions 9 toSetting the Speed of the Camera Moving to a Preset Position Installation Removing/Attaching the Cable CoverAttaching an Interface Board To remove the cable coverInstalling the Camera To install the camera on a deskTo remove the interface board To attach the camera to a tripodInstalling the Camera on the Ceiling Before installationInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connecting to an AC Outlet ConnectionsTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with SDI Input Connector Connecting a VTR Equipped with HD-SDI Input ConnectorsConnecting a Computer Connecting the BRU-H700 HD Optical Multiplex UnitConnecting a Video Switcher Cable Second BRCConnecting a Sync Signal Generator To connect multiple cameras to the HD sync signal generatorTo connect a single camera To connect multiple cameras to the SD sync signal generator SyncIndicators on the BRC-H700 camera Error messages for the BRU-H700 HD Optical Multiplex UnitList of Messages Messages for the BRC-H700 cameraTroubleshooting Symptom Cause RemedySymptom Cause Remedy Menu Configuration SpeedSTD RGB Presetting Items Presetting menu itemsSUB OUT ADD Sync IMG Size Specifications Input/output connectorsSupplied accessories SystemDimensions BRC-H700 Video CameraCeiling Bracket B Top SideRM-BR300 Remote Control Unit Top BRU-H700 HD Optical Multiplex Unit Top Front SideVisca RS-422 connector connector plug 9-pin Visca RS-232C in connector mini-DIN 8-pin, femaleVisca RS-232C OUT connector mini DIN 8-pin, female Pin AssignmentsRM-BR300 Remote Control Unit optional BRU-H700 HD Optical Multiplex Unit optionalVisca RS-232C OUT connector mini DIN 8-pin FemalePin Wiring Diagram of Visca RS-422 Connection Third to Seventh BRC-H700 or BRU-H700Second BRC-H700 or BRU-H700 Using the Visca RS-422 Connector Plug To remove the connector plug
Top Page Image Contents