Sony HD 3CCD operating instructions Connecting a Sync Signal Generator, To connect a single camera

Page 62

Connecting a Sync Signal

Generator

To connect a single camera

75-ohm termination switch: ON

to AC outlet

EXT SYNC IN

75-ohm coaxial cable

	Installation	to SYNC OUT
		Sync signal generator
	and Connections

To connect multiple cameras to the HD sync signal generator

You can connect up to seven cameras.

Third to Seventh (last)

BRC-H700

		75-ohm termination
		switch: ON
		to AC outlet
		EXT SYNC IN
		Second BRC-H700
		75-ohm termination
	availableCommercially separatorsignaltype-T	switch: OFF
	availableCommercially separatorsignaltype-T	to AC outlet
		to AC outlet
		EXT SYNC IN
		First BRC-H700
		75-ohm termination
		switch: OFF
		to AC outlet
		EXT SYNC IN
		75-ohm coaxial cable
		to SYNC OUT
		HD sync signal generator

62

Connections

Image 62

Contents HD 3CCD Color Video Camera For the customers in Canada Owner’s RecordFor customers in the U.S.A Pour les utilisateurs au CanadaTable of Contents Installation and Connections AppendixPrecautions Typical CCD PhenomenaLong-distance image transmission and pan/tilt/zoom control FeaturesBuilt-in interface card slot Visca camera protocol supportedSystem Components Supplied Components and AccessoriesMounted circuit board using lead-free solder External video sync functionOptional Products Remote commanderRM-BR300 Remote Control Unit BRU-H700 HD Optical Multiplex UnitHFBK-HD1 HD Interface Board Video Switcher commercially availableHFBK-SD1 SD Interface Board HFBK-TS1 HDV Interface BoardThis system allows you System ConfigurationSystem configuration Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG Transmitting Audio Signals Using the BRU-H700 CCFC-M100HG BRBK-H700 HDHFBK-TS1 HDV HD video monitor Microphone Front Location and Function of PartsCamera RearSetting of the Bottom switches BottomRemote Commander supplied Lock button and indicator RM-BR300 Remote Control Unit not suppliedInstalling batteries Mode buttonWhen the menu of the camera is not displayed When the menu of the camera is displayedVisca RS-422 connector Mode selectorVisca RS-232C connector TALLY/CONTACT connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-SD1 SD Interface Board not supplied HFBK-HD1 HD Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied HFBK-XG1 XGA Interface Board not suppliedHFBK-TS1 HDV Interface Board not supplied Main Menu Setting MenusAbout On-Screen Menus To return to the main menu Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the normal display4,5 Spot Light Exposure MenuBack Light When ONE Push is selected Using the ND FilterWhite Balance white balance mode Color MenuPicture Menu Focus Menu Black and white modeMode focus mode Color BARPAN Tilt Zoom Menu Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP Ramp CurveSync Master System MenuAnalog OUT SUB OUT1 Status MenuDown Converter Menu ADD SyncSync VD HD-SDI MenuPC-OUTPUT Menu SyncAudio Delay HDV MenuPanning and Tilting Turning on the PowerPan/Tilt and Zoom Operation If the Standby lamp of the camera flashes Operating Multiple Cameras with the Remote CommanderZooming Shooting with Back Lighting Adjusting the CameraFocusing on a Subject To focus the camera on a subject automaticallyTo recall the stored settings To cancel the preset memoryTo assign camera addresses automatically To illuminate the panel of the Remote Control UnitOperating Multiple Cameras Direction REV 1STD PAN-TILT Reset To assign camera addresses manuallyTurn the dial on the upper part of the joystick To adjust the white balance automatically Adjusting the White BalanceOne-push auto focusing during manual focus adjustment To adjust the white balance manuallyFunctions of the R and B controls Adjusting the BrightnessFunctions of the Value and Bright controls Storing Camera Settings To select positions 9 toSetting the Speed of the Camera Moving to a Preset Position Attaching an Interface Board InstallationRemoving/Attaching the Cable Cover To remove the cable coverTo remove the interface board Installing the CameraTo install the camera on a desk To attach the camera to a tripodInstallation example Installing the Camera on the CeilingBefore installation Attachment materials Ceiling Hole Ceiling bracket B To remove the camera Connecting to an AC OutletConnections Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with SDI Input Connector Connecting a VTR Equipped with HD-SDI Input ConnectorsConnecting a Computer Connecting the BRU-H700 HD Optical Multiplex UnitConnecting a Video Switcher Cable Second BRCTo connect a single camera Connecting a Sync Signal GeneratorTo connect multiple cameras to the HD sync signal generator To connect multiple cameras to the SD sync signal generator SyncList of Messages Indicators on the BRC-H700 cameraError messages for the BRU-H700 HD Optical Multiplex Unit Messages for the BRC-H700 cameraTroubleshooting Symptom Cause RemedySymptom Cause Remedy Menu Configuration SpeedSTD RGB Presetting Items Presetting menu itemsSUB OUT ADD Sync IMG Size Supplied accessories SpecificationsInput/output connectors SystemCeiling Bracket B DimensionsBRC-H700 Video Camera Top SideRM-BR300 Remote Control Unit Top BRU-H700 HD Optical Multiplex Unit Top Front SideVisca RS-232C OUT connector mini DIN 8-pin, female Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Pin AssignmentsRM-BR300 Remote Control Unit optional BRU-H700 HD Optical Multiplex Unit optionalPin Visca RS-232C OUT connector mini DIN 8-pinFemale Second BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionThird to Seventh BRC-H700 or BRU-H700 Using the Visca RS-422 Connector Plug To remove the connector plug