Sony HD 3CCD HFBK-SD1 SD Interface Board not supplied, HFBK-HD1 HD Interface Board not supplied

Page 25

MVISCA RS-422 connector

Connect to the VISCA RS-422 connector of the camera or another BRU-H700 HD Optical Multiplex Unit.

For the connection to the VISCA RS-422 connector, see “Using the VISCA RS-422 Connector Plug” on back cover.

NVISCA FUNCTION switches

These switches are used for the VISCA communication settings.

Switch 1 (RS-232C/RS-422 selector)

Set to ON for RS-422, or OFF for RS-232C.

Switch 2 (Communication baud rate selector)

Set to ON for 38400bps, or OFF for 9600bps.

Switches 3 to 5 (Camera address selectors)

Set the address of the camera.

Normally set to “0”. With this setting, addresses are assigned to the cameras automatically in the connected order by pressing the POWER button while holding down the RESET button on the RM- BR300 Remote Control Unit.

You can assign the camera address “1” to “7” manually by setting these selectors as follows:

Camera

0

1

2

3

4

5

6

7

address

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch 3 OFF

ON

OFF ON

OFF ON

OFF ON

 

 

 

 

 

 

 

 

Switch 4

OFF

OFF

ON

ON

OFF OFF

ON

ON

 

 

 

 

 

 

 

 

 

Switch 5

OFF

OFF

OFF

OFF

ON

ON

ON

ON

 

 

 

 

 

 

 

 

 

Switch 6 (59.94i/50i signal format selector)

Set to ON for output of 50i signal format, or OFF for output of 59.94i signal format.

Note

Set the switches before you turn on the power of the unit.

HFBK-SD1 SD Interface Board (not supplied)

1 2 3 4

MONITOR

VIDEO

SD-

SDI

 

 

 

 

HFBK-SD1

AMONITOR connector (D-sub 9-pin)

Supplies various analog signals such as composite video, S video, component video and RGB signals. The output signal can be selected in the DOWN CONVERTER menu of the camera.

BDIP switches (inside the cap)

When this interface board is inserted into the BRC- H700 camera or the BRU-H700 HD Optical Multiplex Unit, the DIP switches cannot be used.

CVIDEO connector (BNC type)

Supplies analog composite signals. The aspect ratio can be selected in the DOWN CONVERTER menu of the camera.

DSD-SDI connector (BNC type)

Supplies down-converted SD-SDI signals that conform to SMPTE259M (for 59.94i signal format) or ITU-R BT.656 (for 50i signal format) serial digital interface standards. The aspect ratio can be selected with the DOWN CONVERTER menu of the camera.

HFBK-HD1 HD Interface Board (not supplied)

1 2 3

MONITOR

HD-SDI

 

HD-SDI

 

 

 

 

 

HFBK-HD1

AMONITOR connector (D-sub15-pin)Supplies analog video signals (component or RGB). The output signal can be selected in the HD- SDI menu of the camera.

BDIP switches (inside the cap)

When this interface board is inserted into the BRC- H700 camera or the BRU-H700 HD Optical Multiplex Unit, the DIP switches cannot be used.

Overview

Location and Function of Parts

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents HD 3CCD Color Video Camera For customers in the U.S.A Owner’s RecordFor the customers in Canada Pour les utilisateurs au CanadaTable of Contents Appendix Installation and ConnectionsTypical CCD Phenomena PrecautionsBuilt-in interface card slot FeaturesLong-distance image transmission and pan/tilt/zoom control Visca camera protocol supportedMounted circuit board using lead-free solder Supplied Components and AccessoriesSystem Components External video sync functionRM-BR300 Remote Control Unit Remote commanderOptional Products BRU-H700 HD Optical Multiplex UnitHFBK-SD1 SD Interface Board Video Switcher commercially availableHFBK-HD1 HD Interface Board HFBK-TS1 HDV Interface BoardSystem configuration System ConfigurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG CCFC-M100HG BRBK-H700 HD Transmitting Audio Signals Using the BRU-H700HFBK-TS1 HDV HD video monitor Microphone Camera Location and Function of PartsFront RearBottom Setting of the Bottom switchesRemote Commander supplied Installing batteries RM-BR300 Remote Control Unit not suppliedLock button and indicator Mode buttonWhen the menu of the camera is displayed When the menu of the camera is not displayedVisca RS-232C connector Mode selectorVisca RS-422 connector TALLY/CONTACT connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-HD1 HD Interface Board not supplied HFBK-SD1 SD Interface Board not suppliedHFBK-TS1 HDV Interface Board not supplied HFBK-XG1 XGA Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied About On-Screen Menus Setting MenusMain Menu Operation Through Menus Menu Operation Using the Supplied Remote CommanderTo return to the main menu To return to the normal display4,5 Back Light Exposure MenuSpot Light White Balance white balance mode Using the ND FilterWhen ONE Push is selected Color MenuPicture Menu Mode focus mode Black and white modeFocus Menu Color BARSetting range of Tilt DOWN/TILT UP Setting range of PAN LEFT/PAN RightPAN Tilt Zoom Menu Ramp CurveAnalog OUT System MenuSync Master Down Converter Menu Status MenuSUB OUT1 ADD SyncPC-OUTPUT Menu HD-SDI MenuSync VD SyncHDV Menu Audio DelayPan/Tilt and Zoom Operation Turning on the PowerPanning and Tilting Zooming Operating Multiple Cameras with the Remote CommanderIf the Standby lamp of the camera flashes Focusing on a Subject Adjusting the CameraShooting with Back Lighting To focus the camera on a subject automaticallyTo cancel the preset memory To recall the stored settingsOperating Multiple Cameras To illuminate the panel of the Remote Control UnitTo assign camera addresses automatically To assign camera addresses manually Direction REV 1STD PAN-TILT ResetTurn the dial on the upper part of the joystick One-push auto focusing during manual focus adjustment Adjusting the White BalanceTo adjust the white balance automatically To adjust the white balance manuallyFunctions of the Value and Bright controls Adjusting the BrightnessFunctions of the R and B controls To select positions 9 to Storing Camera SettingsSetting the Speed of the Camera Moving to a Preset Position Removing/Attaching the Cable Cover InstallationAttaching an Interface Board To remove the cable coverTo install the camera on a desk Installing the CameraTo remove the interface board To attach the camera to a tripodBefore installation Installing the Camera on the CeilingInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connections Connecting to an AC OutletTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a VTR Equipped with SDI Input ConnectorConnecting the BRU-H700 HD Optical Multiplex Unit Connecting a ComputerCable Second BRC Connecting a Video SwitcherTo connect multiple cameras to the HD sync signal generator Connecting a Sync Signal GeneratorTo connect a single camera Sync To connect multiple cameras to the SD sync signal generatorError messages for the BRU-H700 HD Optical Multiplex Unit Indicators on the BRC-H700 cameraList of Messages Messages for the BRC-H700 cameraSymptom Cause Remedy TroubleshootingSymptom Cause Remedy Speed Menu ConfigurationSTD RGB Presetting menu items Presetting ItemsSUB OUT ADD Sync IMG Size Input/output connectors SpecificationsSupplied accessories SystemBRC-H700 Video Camera DimensionsCeiling Bracket B Top SideRM-BR300 Remote Control Unit Top Front Side BRU-H700 HD Optical Multiplex Unit TopVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-422 connector connector plug 9-pinVisca RS-232C OUT connector mini DIN 8-pin, female Pin AssignmentsBRU-H700 HD Optical Multiplex Unit optional RM-BR300 Remote Control Unit optionalFemale Visca RS-232C OUT connector mini DIN 8-pinPin Third to Seventh BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionSecond BRC-H700 or BRU-H700 To remove the connector plug Using the Visca RS-422 Connector Plug
Top Page Image Contents