Sony HD 3CCD operating instructions Focus Menu, Black and white mode, Color BAR, Mode focus mode

Page 33

STANDARD: Sets normal picture blur compensation.

HARD: Sets maximum picture blur compensation.

Note

This feature does not function while the camera is panning or tilting.

B&W (black and white mode)

When this item is set to ON, an image is shot in black and white.

COLOR BAR

When this item is set to ON, the built-in color bar of the camera is displayed on the monitor screen.

FOCUS Menu

The FOCUS menu is used to select the focus mode.

<FOCUS>

>MODEAUTO

MODE (focus mode)

Select the focus adjustment mode.

AUTO: The focus is adjusted automatically.

MANUAL: Adjust the focus manually. Use the FAR/ NEAR buttons on the supplied Remote Commander to adjust the focus.

Adjusting and Setting With Menus

FOCUS Menu

33

Image 33

Contents HD 3CCD Color Video Camera For customers in the U.S.A Owner’s RecordFor the customers in Canada Pour les utilisateurs au CanadaTable of Contents Appendix Installation and ConnectionsTypical CCD Phenomena PrecautionsBuilt-in interface card slot FeaturesLong-distance image transmission and pan/tilt/zoom control Visca camera protocol supportedMounted circuit board using lead-free solder Supplied Components and AccessoriesSystem Components External video sync functionRM-BR300 Remote Control Unit Remote commanderOptional Products BRU-H700 HD Optical Multiplex UnitHFBK-SD1 SD Interface Board Video Switcher commercially availableHFBK-HD1 HD Interface Board HFBK-TS1 HDV Interface BoardSystem Configuration System configurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG CCFC-M100HG BRBK-H700 HD Transmitting Audio Signals Using the BRU-H700HFBK-TS1 HDV HD video monitor Microphone Camera Location and Function of PartsFront RearBottom Setting of the Bottom switchesRemote Commander supplied Installing batteries RM-BR300 Remote Control Unit not suppliedLock button and indicator Mode buttonWhen the menu of the camera is displayed When the menu of the camera is not displayedVisca RS-232C connector Mode selectorVisca RS-422 connector TALLY/CONTACT connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-HD1 HD Interface Board not supplied HFBK-SD1 SD Interface Board not suppliedHFBK-XG1 XGA Interface Board not supplied HFBK-TS1 HDV Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied Setting Menus About On-Screen MenusMain Menu Operation Through Menus Menu Operation Using the Supplied Remote CommanderTo return to the main menu To return to the normal display4,5 Exposure Menu Back LightSpot Light White Balance white balance mode Using the ND FilterWhen ONE Push is selected Color MenuPicture Menu Mode focus mode Black and white modeFocus Menu Color BARSetting range of Tilt DOWN/TILT UP Setting range of PAN LEFT/PAN RightPAN Tilt Zoom Menu Ramp CurveSystem Menu Analog OUTSync Master Down Converter Menu Status MenuSUB OUT1 ADD SyncPC-OUTPUT Menu HD-SDI MenuSync VD SyncHDV Menu Audio DelayTurning on the Power Pan/Tilt and Zoom OperationPanning and Tilting Operating Multiple Cameras with the Remote Commander ZoomingIf the Standby lamp of the camera flashes Focusing on a Subject Adjusting the CameraShooting with Back Lighting To focus the camera on a subject automaticallyTo cancel the preset memory To recall the stored settingsTo illuminate the panel of the Remote Control Unit Operating Multiple CamerasTo assign camera addresses automatically To assign camera addresses manually Direction REV 1STD PAN-TILT ResetTurn the dial on the upper part of the joystick One-push auto focusing during manual focus adjustment Adjusting the White BalanceTo adjust the white balance automatically To adjust the white balance manuallyAdjusting the Brightness Functions of the Value and Bright controlsFunctions of the R and B controls To select positions 9 to Storing Camera SettingsSetting the Speed of the Camera Moving to a Preset Position Removing/Attaching the Cable Cover InstallationAttaching an Interface Board To remove the cable coverTo install the camera on a desk Installing the CameraTo remove the interface board To attach the camera to a tripodInstalling the Camera on the Ceiling Before installationInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connecting to an AC Outlet ConnectionsTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a VTR Equipped with SDI Input ConnectorConnecting the BRU-H700 HD Optical Multiplex Unit Connecting a ComputerCable Second BRC Connecting a Video SwitcherConnecting a Sync Signal Generator To connect multiple cameras to the HD sync signal generatorTo connect a single camera Sync To connect multiple cameras to the SD sync signal generatorError messages for the BRU-H700 HD Optical Multiplex Unit Indicators on the BRC-H700 cameraList of Messages Messages for the BRC-H700 cameraSymptom Cause Remedy TroubleshootingSymptom Cause Remedy Speed Menu ConfigurationSTD RGB Presetting menu items Presetting ItemsSUB OUT ADD Sync IMG Size Input/output connectors SpecificationsSupplied accessories SystemBRC-H700 Video Camera DimensionsCeiling Bracket B Top SideRM-BR300 Remote Control Unit Top Front Side BRU-H700 HD Optical Multiplex Unit TopVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-422 connector connector plug 9-pinVisca RS-232C OUT connector mini DIN 8-pin, female Pin AssignmentsBRU-H700 HD Optical Multiplex Unit optional RM-BR300 Remote Control Unit optionalVisca RS-232C OUT connector mini DIN 8-pin FemalePin Wiring Diagram of Visca RS-422 Connection Third to Seventh BRC-H700 or BRU-H700Second BRC-H700 or BRU-H700 To remove the connector plug Using the Visca RS-422 Connector Plug