Sony HD 3CCD operating instructions Connecting a VTR Equipped with SDI Input Connector

Page 59

Connecting a VTR Equipped with SDI Input Connector

When you install an optical HFBK-SD1 SD Interface Board in the camera, you can output the signal from the camera by converting it into an SDI signal that conforms to SMPTE259M (for 59.94i signal format) or ITU-R BT.656 (for 50i signal format) serial digital interface standards.

Connecting a VTR Equipped with HD-SDI Input Connectors

When you install an optional HFBK-HD1 HD Interface Board in the camera, you can output the signal from the camera by converting it into a signal compliant with HD-SDI standards (SMPTE292M serial digital interface).

		to AC outlet
to AC outlet
	HFBK-HD1 HD	HD-SDI
SD-SDI	HFBK-HD1 HD
SD-SDI	Interface Board
HFBK-SD1 SD
Interface Board
		Connecting cable
Connecting cable		with BNC connectors
Connecting cable
with BNC connectors
to SDI input		to HD-SDI
to SDI input		input

Installation and Connections

DVCAM, etc. equipped with an

SDI input comnnector

Notes

•When an optional HFBK-SD1 SD Interface Board is installed in the camera, the DIP switches on the board cannot be used. Use the menus of the camera for various settings.

•Signal processing in the interface board causes all output signals from the HFBK-SD1 to be delayed by approximately 93H (horizontal sync time) compared with the YPbPr/RGB output signals from the camera. A similar delay occurs when using an external sync signal.

HDCAM, etc. equipped with an

HD-SDI input comnnectors

Notes

•When an optional HFBK-HD1 HD Interface Board is installed in the camera, the DIP switches on the board cannot be used. Use the menus of the camera for various settings.

•Signal processing in the interface board causes all output signals from the HFBK-HD1 to be delayed by approximately 4H (horizontal sync time) compared with the YPbPr/RGB output signals from the camera. A similar delay occurs when using an external sync signal.

Connections

59

Image 59

Contents HD 3CCD Color Video Camera Pour les utilisateurs au Canada Owner’s RecordFor customers in the U.S.A For the customers in CanadaTable of Contents Appendix Installation and ConnectionsTypical CCD Phenomena PrecautionsVisca camera protocol supported FeaturesBuilt-in interface card slot Long-distance image transmission and pan/tilt/zoom controlExternal video sync function Supplied Components and AccessoriesMounted circuit board using lead-free solder System ComponentsBRU-H700 HD Optical Multiplex Unit Remote commanderRM-BR300 Remote Control Unit Optional ProductsHFBK-TS1 HDV Interface Board Video Switcher commercially availableHFBK-SD1 SD Interface Board HFBK-HD1 HD Interface BoardThis system allows you System ConfigurationSystem configuration Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG CCFC-M100HG BRBK-H700 HD Transmitting Audio Signals Using the BRU-H700HFBK-TS1 HDV HD video monitor Microphone Rear Location and Function of PartsCamera FrontBottom Setting of the Bottom switchesRemote Commander supplied Mode button RM-BR300 Remote Control Unit not suppliedInstalling batteries Lock button and indicatorWhen the menu of the camera is displayed When the menu of the camera is not displayedTALLY/CONTACT connector Mode selectorVisca RS-232C connector Visca RS-422 connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-HD1 HD Interface Board not supplied HFBK-SD1 SD Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied HFBK-XG1 XGA Interface Board not suppliedHFBK-TS1 HDV Interface Board not supplied Main Menu Setting MenusAbout On-Screen Menus To return to the normal display Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the main menu4,5 Spot Light Exposure MenuBack Light Color Menu Using the ND FilterWhite Balance white balance mode When ONE Push is selectedPicture Menu Color BAR Black and white modeMode focus mode Focus MenuRamp Curve Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP PAN Tilt Zoom MenuSync Master System MenuAnalog OUT ADD Sync Status MenuDown Converter Menu SUB OUT1Sync HD-SDI MenuPC-OUTPUT Menu Sync VDHDV Menu Audio DelayPanning and Tilting Turning on the PowerPan/Tilt and Zoom Operation If the Standby lamp of the camera flashes Operating Multiple Cameras with the Remote CommanderZooming To focus the camera on a subject automatically Adjusting the CameraFocusing on a Subject Shooting with Back LightingTo cancel the preset memory To recall the stored settingsTo assign camera addresses automatically To illuminate the panel of the Remote Control UnitOperating Multiple Cameras To assign camera addresses manually Direction REV 1STD PAN-TILT ResetTurn the dial on the upper part of the joystick To adjust the white balance manually Adjusting the White BalanceOne-push auto focusing during manual focus adjustment To adjust the white balance automaticallyFunctions of the R and B controls Adjusting the BrightnessFunctions of the Value and Bright controls To select positions 9 to Storing Camera SettingsSetting the Speed of the Camera Moving to a Preset Position To remove the cable cover InstallationRemoving/Attaching the Cable Cover Attaching an Interface BoardTo attach the camera to a tripod Installing the CameraTo install the camera on a desk To remove the interface boardInstallation example Installing the Camera on the CeilingBefore installation Attachment materials Ceiling Hole Ceiling bracket B To remove the camera Connecting to an AC OutletConnections Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a VTR Equipped with SDI Input ConnectorConnecting the BRU-H700 HD Optical Multiplex Unit Connecting a ComputerCable Second BRC Connecting a Video SwitcherTo connect a single camera Connecting a Sync Signal GeneratorTo connect multiple cameras to the HD sync signal generator Sync To connect multiple cameras to the SD sync signal generatorMessages for the BRC-H700 camera Indicators on the BRC-H700 cameraError messages for the BRU-H700 HD Optical Multiplex Unit List of MessagesSymptom Cause Remedy TroubleshootingSymptom Cause Remedy Speed Menu ConfigurationSTD RGB Presetting menu items Presetting ItemsSUB OUT ADD Sync IMG Size System SpecificationsInput/output connectors Supplied accessoriesTop Side DimensionsBRC-H700 Video Camera Ceiling Bracket BRM-BR300 Remote Control Unit Top Front Side BRU-H700 HD Optical Multiplex Unit TopPin Assignments Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-232C OUT connector mini DIN 8-pin, femaleBRU-H700 HD Optical Multiplex Unit optional RM-BR300 Remote Control Unit optionalPin Visca RS-232C OUT connector mini DIN 8-pinFemale Second BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionThird to Seventh BRC-H700 or BRU-H700 To remove the connector plug Using the Visca RS-422 Connector Plug