Sony HD 3CCD Using the Visca RS-422 Connector Plug, To remove the connector plug

Page 80

Using the VISCA RS-422 Connector Plug

1 Insert a wire (AWG Nos. 28 to 18) into the desired wire opening on the VISCA RS-422 connector plug, and tighten the screw for that wire using a flat- head screwdriver.

Flat-head screwdriver

To remove the connector plug

Grasp both ends of the VISCA RS-422 connector plug and pull it out as shown in the illustration.

1

2

3

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wire

2 Insert the VISCA RS-422 connector plug into the VISCA RS-422 connector.

1

2

3

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Printed on 100% recycled paper.

Notes

In order to stabilize the voltage level of the signal, connect both ends to GND.

When the connections using the VISCA RS-422 connectors are made, the VISCA RS-232C connection is not available.

The maximum connection distance with the VISCA RS-422 connection is approximately 1,200 m (3,937 feet).

Sony Corporation

Printed in Japan

Image 80
Contents HD 3CCD Color Video Camera Owner’s Record For customers in the U.S.AFor the customers in Canada Pour les utilisateurs au CanadaTable of Contents Installation and Connections AppendixPrecautions Typical CCD PhenomenaFeatures Built-in interface card slotLong-distance image transmission and pan/tilt/zoom control Visca camera protocol supportedSupplied Components and Accessories Mounted circuit board using lead-free solderSystem Components External video sync functionRemote commander RM-BR300 Remote Control UnitOptional Products BRU-H700 HD Optical Multiplex UnitVideo Switcher commercially available HFBK-SD1 SD Interface BoardHFBK-HD1 HD Interface Board HFBK-TS1 HDV Interface BoardThis system allows you System ConfigurationSystem configuration Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG Transmitting Audio Signals Using the BRU-H700 CCFC-M100HG BRBK-H700 HDHFBK-TS1 HDV HD video monitor Microphone Location and Function of Parts CameraFront RearSetting of the Bottom switches BottomRemote Commander supplied RM-BR300 Remote Control Unit not supplied Installing batteriesLock button and indicator Mode buttonWhen the menu of the camera is not displayed When the menu of the camera is displayedMode selector Visca RS-232C connectorVisca RS-422 connector TALLY/CONTACT connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-SD1 SD Interface Board not supplied HFBK-HD1 HD Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied HFBK-XG1 XGA Interface Board not suppliedHFBK-TS1 HDV Interface Board not supplied Main Menu Setting MenusAbout On-Screen Menus Menu Operation Using the Supplied Remote Commander Operation Through MenusTo return to the main menu To return to the normal display4,5 Spot Light Exposure MenuBack Light Using the ND Filter White Balance white balance modeWhen ONE Push is selected Color MenuPicture Menu Black and white mode Mode focus modeFocus Menu Color BARSetting range of PAN LEFT/PAN Right Setting range of Tilt DOWN/TILT UPPAN Tilt Zoom Menu Ramp CurveSync Master System MenuAnalog OUT Status Menu Down Converter MenuSUB OUT1 ADD SyncHD-SDI Menu PC-OUTPUT MenuSync VD SyncAudio Delay HDV MenuPanning and Tilting Turning on the PowerPan/Tilt and Zoom Operation If the Standby lamp of the camera flashes Operating Multiple Cameras with the Remote CommanderZooming Adjusting the Camera Focusing on a SubjectShooting with Back Lighting To focus the camera on a subject automaticallyTo recall the stored settings To cancel the preset memoryTo assign camera addresses automatically To illuminate the panel of the Remote Control UnitOperating Multiple Cameras Direction REV 1STD PAN-TILT Reset To assign camera addresses manuallyTurn the dial on the upper part of the joystick Adjusting the White Balance One-push auto focusing during manual focus adjustmentTo adjust the white balance automatically To adjust the white balance manuallyFunctions of the R and B controls Adjusting the BrightnessFunctions of the Value and Bright controls Storing Camera Settings To select positions 9 toSetting the Speed of the Camera Moving to a Preset Position Installation Removing/Attaching the Cable CoverAttaching an Interface Board To remove the cable coverInstalling the Camera To install the camera on a deskTo remove the interface board To attach the camera to a tripodInstallation example Installing the Camera on the CeilingBefore installation Attachment materials Ceiling Hole Ceiling bracket B To remove the camera Connecting to an AC OutletConnections Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with SDI Input Connector Connecting a VTR Equipped with HD-SDI Input ConnectorsConnecting a Computer Connecting the BRU-H700 HD Optical Multiplex UnitConnecting a Video Switcher Cable Second BRCTo connect a single camera Connecting a Sync Signal GeneratorTo connect multiple cameras to the HD sync signal generator To connect multiple cameras to the SD sync signal generator SyncIndicators on the BRC-H700 camera Error messages for the BRU-H700 HD Optical Multiplex UnitList of Messages Messages for the BRC-H700 cameraTroubleshooting Symptom Cause RemedySymptom Cause Remedy Menu Configuration SpeedSTD RGB Presetting Items Presetting menu itemsSUB OUT ADD Sync IMG Size Specifications Input/output connectorsSupplied accessories SystemDimensions BRC-H700 Video CameraCeiling Bracket B Top SideRM-BR300 Remote Control Unit Top BRU-H700 HD Optical Multiplex Unit Top Front SideVisca RS-422 connector connector plug 9-pin Visca RS-232C in connector mini-DIN 8-pin, femaleVisca RS-232C OUT connector mini DIN 8-pin, female Pin AssignmentsRM-BR300 Remote Control Unit optional BRU-H700 HD Optical Multiplex Unit optionalPin Visca RS-232C OUT connector mini DIN 8-pinFemale Second BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionThird to Seventh BRC-H700 or BRU-H700 Using the Visca RS-422 Connector Plug To remove the connector plug