Sony HD 3CCD operating instructions Setting of the Bottom switches

Page 19

OEXT SYNC IN connector Accepts external video sync signals.

PCard slot

Insert an optional interface board, HFBK-HD1, HFBK-SD1, HFBK-XG1, HFBK-TS1 or BRBK- H700.

The slot cover is attached to the camera at the factory.

Q RGB/COMPONENT connector

Supplies the images as analog component (YPbPr or RGB) signal.

RDATA MIX switch

Set the switch to ON to overlap the menu with the video signal output from the installed interface board. Set it to OFF not to overlap the menu.

SCable cover

The cable cover is attached to the camera at the factory. To remove the cable cover, see page 50.

Note

Do not carry the camera by holding the cable cover. Otherwise, the cable cover may come off and the camera may fall.

Bottom

w; wa ws

TCeiling bracket mounting screw holes

When you install the camera to the ceiling, secure the supplied ceiling bracket to these holes using the supplied four screws. The four feet are attached to the holes at the factory.

For installation, see “Installing the Camera on the Ceiling” on page 52.

UTripod screw holes (1/4-20UNC)

When you install the camera to a tripod, secure the tripod to these holes.

VBOTTOM switches

Used for the output signal format selection, RS- 232C/RS-422 selection, baud rate selection, remote control signal output on/off and camera address setting.

For details, see “Setting of the BOTTOM switches” on page 19.

Setting of the BOTTOM switches

 

 

1

1

O

2

 

2

N

3

4

 

3

 

 

 

 

4

1

O

5

3

N

2

 

4

 

 

1Switch 1 (59.94i/50i signal format selector) Set to ON for output of 50i signal format, or OFF for output of 59.94i signal format.

2Switch 2 (RS-232C/RS-422 selector)

Set to ON for RS-422, or OFF for RS-232C.

3Switch 3 (Communication baud rate selector) Set to ON for 38400bps, or OFF for 9600bps.

4Switch 4 (Infrared signal output switch)

Set to ON to enable an infrared signal output, or OFF to disable the output.

5Camera address selectors Set the address of the camera.

Normally set to “0”. With this setting, addresses are assigned to the cameras automatically in the connected order by pressing the POWER button while holding down the RESET button on the RM- BR300 Remote Control Unit.

You can assign the camera address “1” to “7” manually by setting these selectors as follows:

Camera

0

1

2

3

4

5

6

7

address

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Switch 1

OFF

ON

OFF

ON

OFF

ON

OFF

ON

 

 

 

 

 

 

 

 

 

Switch 2

OFF

OFF

ON

ON

OFF

OFF

ON

ON

 

 

 

 

 

 

 

 

 

Switch 3

OFF

OFF

OFF

OFF

ON

ON

ON

ON

 

 

 

 

 

 

 

 

 

Switch 4 is not used.

Note

Set the switches before you turn on the power of the camera.

Overview

Location and Function of Parts

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents HD 3CCD Color Video Camera Pour les utilisateurs au Canada Owner’s RecordFor customers in the U.S.A For the customers in CanadaTable of Contents Appendix Installation and ConnectionsTypical CCD Phenomena PrecautionsVisca camera protocol supported FeaturesBuilt-in interface card slot Long-distance image transmission and pan/tilt/zoom controlExternal video sync function Supplied Components and AccessoriesMounted circuit board using lead-free solder System ComponentsBRU-H700 HD Optical Multiplex Unit Remote commanderRM-BR300 Remote Control Unit Optional ProductsHFBK-TS1 HDV Interface Board Video Switcher commercially availableHFBK-SD1 SD Interface Board HFBK-HD1 HD Interface BoardSystem configuration System ConfigurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG CCFC-M100HG BRBK-H700 HD Transmitting Audio Signals Using the BRU-H700HFBK-TS1 HDV HD video monitor Microphone Rear Location and Function of PartsCamera FrontBottom Setting of the Bottom switchesRemote Commander supplied Mode button RM-BR300 Remote Control Unit not suppliedInstalling batteries Lock button and indicatorWhen the menu of the camera is displayed When the menu of the camera is not displayedTALLY/CONTACT connector Mode selectorVisca RS-232C connector Visca RS-422 connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-HD1 HD Interface Board not supplied HFBK-SD1 SD Interface Board not suppliedHFBK-TS1 HDV Interface Board not supplied HFBK-XG1 XGA Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied About On-Screen Menus Setting MenusMain Menu To return to the normal display Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the main menu4,5 Back Light Exposure MenuSpot Light Color Menu Using the ND FilterWhite Balance white balance mode When ONE Push is selectedPicture Menu Color BAR Black and white modeMode focus mode Focus MenuRamp Curve Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP PAN Tilt Zoom MenuAnalog OUT System MenuSync Master ADD Sync Status MenuDown Converter Menu SUB OUT1Sync HD-SDI MenuPC-OUTPUT Menu Sync VDHDV Menu Audio DelayPan/Tilt and Zoom Operation Turning on the PowerPanning and Tilting Zooming Operating Multiple Cameras with the Remote CommanderIf the Standby lamp of the camera flashes To focus the camera on a subject automatically Adjusting the CameraFocusing on a Subject Shooting with Back LightingTo cancel the preset memory To recall the stored settingsOperating Multiple Cameras To illuminate the panel of the Remote Control UnitTo assign camera addresses automatically To assign camera addresses manually Direction REV 1STD PAN-TILT ResetTurn the dial on the upper part of the joystick To adjust the white balance manually Adjusting the White BalanceOne-push auto focusing during manual focus adjustment To adjust the white balance automaticallyFunctions of the Value and Bright controls Adjusting the BrightnessFunctions of the R and B controls To select positions 9 to Storing Camera SettingsSetting the Speed of the Camera Moving to a Preset Position To remove the cable cover InstallationRemoving/Attaching the Cable Cover Attaching an Interface BoardTo attach the camera to a tripod Installing the CameraTo install the camera on a desk To remove the interface boardBefore installation Installing the Camera on the CeilingInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connections Connecting to an AC OutletTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a VTR Equipped with SDI Input ConnectorConnecting the BRU-H700 HD Optical Multiplex Unit Connecting a ComputerCable Second BRC Connecting a Video SwitcherTo connect multiple cameras to the HD sync signal generator Connecting a Sync Signal GeneratorTo connect a single camera Sync To connect multiple cameras to the SD sync signal generatorMessages for the BRC-H700 camera Indicators on the BRC-H700 cameraError messages for the BRU-H700 HD Optical Multiplex Unit List of MessagesSymptom Cause Remedy TroubleshootingSymptom Cause Remedy Speed Menu ConfigurationSTD RGB Presetting menu items Presetting ItemsSUB OUT ADD Sync IMG Size System SpecificationsInput/output connectors Supplied accessoriesTop Side DimensionsBRC-H700 Video Camera Ceiling Bracket BRM-BR300 Remote Control Unit Top Front Side BRU-H700 HD Optical Multiplex Unit TopPin Assignments Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-232C OUT connector mini DIN 8-pin, femaleBRU-H700 HD Optical Multiplex Unit optional RM-BR300 Remote Control Unit optionalFemale Visca RS-232C OUT connector mini DIN 8-pinPin Third to Seventh BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionSecond BRC-H700 or BRU-H700 To remove the connector plug Using the Visca RS-422 Connector Plug
Top Page Image Contents