Sony HD 3CCD operating instructions BRU-H700 HD Optical Multiplex Unit not supplied

Page 24

Overview

BRU-H700 HD Optical Multiplex Unit (not supplied)

Front

1 2 3

APower switch

Turns on/off the power of the HD Optical Multiplex Unit.

Turn on the power of the BRC-H700 camera before you turn on the HD Optical Multiplex Unit.

BPower indicator

Lit in green: The HD Optical Multiplex Unit is in normal operation.

Lit in red: The power of the camera is turned off. Turn it on.

Flashing in red: Abnormal operation of the HD Optical Multiplex Unit. Display the component video signal on the monitor and check the error message. Check also the connection.

For the error message, see “List of Messages” on page 64.

CDATA MIX switch

Set the switch to ON to overlap the menu with the video signal output from the installed interface board. Set it to OFF not to overlap the menu.

Rear

4		5 6
		AUDIO OUT
		L
		R
		FUNCTION ~AC IN
		1	6
		VISCA RS-422
CAMERA IN EXT SYNC OUT	RGB/COMPONENT	IN VISCA RS-232C OUT
7 8 9	0	qa qs qd	qf

DCard slot

Insert an optional interface board, HFBK-SD1, HFBK-HD1, HFBK-XG1 or HFBK-TS1.

The slot cover is attached to the unit at the factory.

EAUDIO OUT L/R jacks

Loop through output of the audio line signal input from the AUDIO IN jacks on the BRBK-H700 HD Optical Multiplex Card inserted into the camera via the Optical Fiber Cable.

F~AC IN connector

Connect the supplied AC power cord.

GCAMERA connector

Connect to the optical connector of the BRBK- H700 HD Optical Multiplex Card installed in the BRC-H700 camera using the CCFC-M100HG Optical Fiber Cable.

A dustproof cap is attached at the factory.

HEXT SYNC IN connector Accepts external video sync signals.

IEXT SYNC OUT connector

Supplies external video sync signals input from the EXT SYNC IN connector.

J RGB/COMPONENT connector

Supplies the images from the camera as YPbPr or RGB signal.

KVISCA RS-232C IN connector

Connect to the RM-BR300 Remote Control Unit (not supplied). When you connect multiple cameras, connect it to the VISCA RS-232C OUT connector of the previous camera in the daisy chain connection.

LVISCA RS-232C OUT connector

When you connect multiple cameras, connect it to the VISCA RS-232C IN connector of the next camera in the daisy chain connection.

24

Location and Function of Parts

Image 24

Contents HD 3CCD Color Video Camera Owner’s Record For customers in the U.S.AFor the customers in Canada Pour les utilisateurs au CanadaTable of Contents Installation and Connections AppendixPrecautions Typical CCD PhenomenaFeatures Built-in interface card slotLong-distance image transmission and pan/tilt/zoom control Visca camera protocol supportedSupplied Components and Accessories Mounted circuit board using lead-free solderSystem Components External video sync functionRemote commander RM-BR300 Remote Control UnitOptional Products BRU-H700 HD Optical Multiplex UnitVideo Switcher commercially available HFBK-SD1 SD Interface BoardHFBK-HD1 HD Interface Board HFBK-TS1 HDV Interface BoardSystem Configuration System configurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG Transmitting Audio Signals Using the BRU-H700 CCFC-M100HG BRBK-H700 HDHFBK-TS1 HDV HD video monitor Microphone Location and Function of Parts CameraFront RearSetting of the Bottom switches BottomRemote Commander supplied RM-BR300 Remote Control Unit not supplied Installing batteriesLock button and indicator Mode buttonWhen the menu of the camera is not displayed When the menu of the camera is displayedMode selector Visca RS-232C connectorVisca RS-422 connector TALLY/CONTACT connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-SD1 SD Interface Board not supplied HFBK-HD1 HD Interface Board not suppliedHFBK-XG1 XGA Interface Board not supplied HFBK-TS1 HDV Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied Setting Menus About On-Screen MenusMain Menu Menu Operation Using the Supplied Remote Commander Operation Through MenusTo return to the main menu To return to the normal display4,5 Exposure Menu Back LightSpot Light Using the ND Filter White Balance white balance modeWhen ONE Push is selected Color MenuPicture Menu Black and white mode Mode focus modeFocus Menu Color BARSetting range of PAN LEFT/PAN Right Setting range of Tilt DOWN/TILT UPPAN Tilt Zoom Menu Ramp CurveSystem Menu Analog OUTSync Master Status Menu Down Converter MenuSUB OUT1 ADD SyncHD-SDI Menu PC-OUTPUT MenuSync VD SyncAudio Delay HDV MenuTurning on the Power Pan/Tilt and Zoom OperationPanning and Tilting Operating Multiple Cameras with the Remote Commander ZoomingIf the Standby lamp of the camera flashes Adjusting the Camera Focusing on a SubjectShooting with Back Lighting To focus the camera on a subject automaticallyTo recall the stored settings To cancel the preset memoryTo illuminate the panel of the Remote Control Unit Operating Multiple CamerasTo assign camera addresses automatically Direction REV 1STD PAN-TILT Reset To assign camera addresses manuallyTurn the dial on the upper part of the joystick Adjusting the White Balance One-push auto focusing during manual focus adjustmentTo adjust the white balance automatically To adjust the white balance manuallyAdjusting the Brightness Functions of the Value and Bright controlsFunctions of the R and B controls Storing Camera Settings To select positions 9 toSetting the Speed of the Camera Moving to a Preset Position Installation Removing/Attaching the Cable CoverAttaching an Interface Board To remove the cable coverInstalling the Camera To install the camera on a deskTo remove the interface board To attach the camera to a tripodInstalling the Camera on the Ceiling Before installationInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connecting to an AC Outlet ConnectionsTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with SDI Input Connector Connecting a VTR Equipped with HD-SDI Input ConnectorsConnecting a Computer Connecting the BRU-H700 HD Optical Multiplex UnitConnecting a Video Switcher Cable Second BRCConnecting a Sync Signal Generator To connect multiple cameras to the HD sync signal generatorTo connect a single camera To connect multiple cameras to the SD sync signal generator SyncIndicators on the BRC-H700 camera Error messages for the BRU-H700 HD Optical Multiplex UnitList of Messages Messages for the BRC-H700 cameraTroubleshooting Symptom Cause RemedySymptom Cause Remedy Menu Configuration SpeedSTD RGB Presetting Items Presetting menu itemsSUB OUT ADD Sync IMG Size Specifications Input/output connectorsSupplied accessories SystemDimensions BRC-H700 Video CameraCeiling Bracket B Top SideRM-BR300 Remote Control Unit Top BRU-H700 HD Optical Multiplex Unit Top Front SideVisca RS-422 connector connector plug 9-pin Visca RS-232C in connector mini-DIN 8-pin, femaleVisca RS-232C OUT connector mini DIN 8-pin, female Pin AssignmentsRM-BR300 Remote Control Unit optional BRU-H700 HD Optical Multiplex Unit optionalVisca RS-232C OUT connector mini DIN 8-pin FemalePin Wiring Diagram of Visca RS-422 Connection Third to Seventh BRC-H700 or BRU-H700Second BRC-H700 or BRU-H700 Using the Visca RS-422 Connector Plug To remove the connector plug