Sony HD 3CCD Connecting a Computer, Connecting the BRU-H700 HD Optical Multiplex Unit

Page 60

Connecting a Computer

When you install an optional HFBK-XG1 XGA Interface Board into the camera, you can output the signal from the camera by converting it into a signal compliant with the VESA (VGA, XGA or WXGA) standards.

to AC outlet

MONITOR

HFBK-XG1 XGA

Interface Board

 

to AC outlet

 

Optical connector

BRBK-H700 Optical

AC power cord

Multiplex Card

(supplied with the

 

CCFC-M100HG Optical

BRU-H700

 

Fiber Cable

 

to AC

outlet

CAMERA

BRU-H700 HD

L AUDIO Optical Multiplex

R Unit

FUNCTION ~

1 6

VISCA RS-422

CAMERA IN EXT SYNC OUT

IN

RS-232C OUT

AC IN

Connecting cable with D-sub 15-pin connectors

Installationand

to RGB input

 

Connections

Computer

 

RGB/

COMPONENT

connecting cable with D-sub 15-pin connectors

to RGB/ component input

HD monitor, etc.

VISCA RS-232C IN

RS-232C cable (supplied with the RM-BR300)*

Connecting the BRU-H700 HD Optical Multiplex Unit

When you install an optional BRBK-H700 Optical Multiplex Card in the camera, you can connect the camera to the BRU-H700 Optical Multiplex Unit using the CCFC-M100HG Optical Fiber Cable. This allows you to control the camera from up to 1,000 m (3,281 feet) away.

VISCA RS-232C

RM-BR300 Remote Control Unit

to AC outlet

*The VISCA RS-422 connection is also available if you use the VISCA RS-422 connectors.

Notes

•When the connection using the Optical Fiber Cable is made, the VISCA RS-232C and VISCA RS-422 connectors on the camera cannot be used.

•When using the VISCA RS-232C connectors or VISCA RS-422 connectors, check the VISCA

60

Connections

Page 59 Page 61
Image 60
Page 59 Page 61
Contents HD 3CCD Color Video Camera Owner’s Record For customers in the U.S.AFor the customers in Canada Pour les utilisateurs au CanadaTable of Contents Installation and Connections AppendixPrecautions Typical CCD PhenomenaFeatures Built-in interface card slotLong-distance image transmission and pan/tilt/zoom control Visca camera protocol supportedSupplied Components and Accessories Mounted circuit board using lead-free solderSystem Components External video sync functionRemote commander RM-BR300 Remote Control UnitOptional Products BRU-H700 HD Optical Multiplex UnitVideo Switcher commercially available HFBK-SD1 SD Interface BoardHFBK-HD1 HD Interface Board HFBK-TS1 HDV Interface BoardSystem Configuration System configurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG Transmitting Audio Signals Using the BRU-H700 CCFC-M100HG BRBK-H700 HDHFBK-TS1 HDV HD video monitor Microphone Location and Function of Parts CameraFront RearSetting of the Bottom switches BottomRemote Commander supplied RM-BR300 Remote Control Unit not supplied Installing batteriesLock button and indicator Mode buttonWhen the menu of the camera is not displayed When the menu of the camera is displayedMode selector Visca RS-232C connectorVisca RS-422 connector TALLY/CONTACT connectorBRU-H700 HD Optical Multiplex Unit not supplied HFBK-SD1 SD Interface Board not supplied HFBK-HD1 HD Interface Board not suppliedHFBK-XG1 XGA Interface Board not supplied HFBK-TS1 HDV Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied Setting Menus About On-Screen MenusMain Menu Menu Operation Using the Supplied Remote Commander Operation Through MenusTo return to the main menu To return to the normal display4,5 Exposure Menu Back LightSpot Light Using the ND Filter White Balance white balance modeWhen ONE Push is selected Color MenuPicture Menu Black and white mode Mode focus modeFocus Menu Color BARSetting range of PAN LEFT/PAN Right Setting range of Tilt DOWN/TILT UPPAN Tilt Zoom Menu Ramp CurveSystem Menu Analog OUTSync Master Status Menu Down Converter MenuSUB OUT1 ADD SyncHD-SDI Menu PC-OUTPUT MenuSync VD SyncAudio Delay HDV MenuTurning on the Power Pan/Tilt and Zoom OperationPanning and Tilting Operating Multiple Cameras with the Remote Commander ZoomingIf the Standby lamp of the camera flashes Adjusting the Camera Focusing on a SubjectShooting with Back Lighting To focus the camera on a subject automaticallyTo recall the stored settings To cancel the preset memoryTo illuminate the panel of the Remote Control Unit Operating Multiple CamerasTo assign camera addresses automatically Direction REV 1STD PAN-TILT Reset To assign camera addresses manuallyTurn the dial on the upper part of the joystick Adjusting the White Balance One-push auto focusing during manual focus adjustmentTo adjust the white balance automatically To adjust the white balance manuallyAdjusting the Brightness Functions of the Value and Bright controlsFunctions of the R and B controls Storing Camera Settings To select positions 9 toSetting the Speed of the Camera Moving to a Preset Position Installation Removing/Attaching the Cable CoverAttaching an Interface Board To remove the cable coverInstalling the Camera To install the camera on a deskTo remove the interface board To attach the camera to a tripodInstalling the Camera on the Ceiling Before installationInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connecting to an AC Outlet ConnectionsTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with SDI Input Connector Connecting a VTR Equipped with HD-SDI Input ConnectorsConnecting a Computer Connecting the BRU-H700 HD Optical Multiplex UnitConnecting a Video Switcher Cable Second BRCConnecting a Sync Signal Generator To connect multiple cameras to the HD sync signal generatorTo connect a single camera To connect multiple cameras to the SD sync signal generator SyncIndicators on the BRC-H700 camera Error messages for the BRU-H700 HD Optical Multiplex UnitList of Messages Messages for the BRC-H700 cameraTroubleshooting Symptom Cause RemedySymptom Cause Remedy Menu Configuration SpeedSTD RGB Presetting Items Presetting menu itemsSUB OUT ADD Sync IMG Size Specifications Input/output connectorsSupplied accessories SystemDimensions BRC-H700 Video CameraCeiling Bracket B Top SideRM-BR300 Remote Control Unit Top BRU-H700 HD Optical Multiplex Unit Top Front SideVisca RS-422 connector connector plug 9-pin Visca RS-232C in connector mini-DIN 8-pin, femaleVisca RS-232C OUT connector mini DIN 8-pin, female Pin AssignmentsRM-BR300 Remote Control Unit optional BRU-H700 HD Optical Multiplex Unit optionalVisca RS-232C OUT connector mini DIN 8-pin FemalePin Wiring Diagram of Visca RS-422 Connection Third to Seventh BRC-H700 or BRU-H700Second BRC-H700 or BRU-H700 Using the Visca RS-422 Connector Plug To remove the connector plug
Top Page Image Contents