JVC GV-DS2 manual EN Getting Started, What is video capture software ?, What is Jlip ?

Page 16

16EN GETTINGSTARTED

What is video capture software ?

Video capture software is a type of application program that allows you to capture video images from camcorders and VCRs and store them in personal computers running under the Windows® operating system. These images can be transferred from the video source to the computer via a standard RS-232C communication interface. By processing the captured images with commercially available image editing software, you can create your own unique and highly personal illustrations and graphics for incorporation into everything from postcards to newsletters and Internet homepages. What’s more, you can also use your computer to edit your original video recording and produce a fun-to-watch, professional-looking video pro- gram.

What is JLIP ?

JLIP* stands for Joint Level Interface Protocol, a new communication protocol which allows AV units equipped with a JLIP terminal to be controlled by a personal computer.

* is a registered trademark of JVC.

Operating Environment

●Personal computer with Microsoft® Windows® 3.1 or Windows® 95

●CPU Intel DX4® or higher processor

●Minimum RAM requirement: more than 8 MB

●Available Hard Disk space of at least 8 MB

●Colour display capable of at least 640 x 480 pixels, 256 colours Recommended 1024 x 768, 16.77 Mil colours

●1 free serial transmission port, compatible with 9600 bps transmission rate, connectable to RS-232C with 9 pin serial connector.

Recommended compatible with UART 16550A

●Mouse (Windows® compatible)

●CD-ROM drive

Note : An optional 9 pin serial conversion adapter is required for computers using serial communication port other than standard 9 pin.

*Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

*Other product and company names included in this instruction manual are trademarks and/or registered trademarks of their respective holders.

Connectable Devices

●When using JLIP with Video units equipped with a JLIP connector : GR-DVX series

●The JLIP Video Capture Software can be used with the GV-CB1 and GV-DS1.

Image 16

Contents GV-DS2 Dear Customer It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment Maintenance How to handle a CD-ROMDo not place the Video Capture Docking Station Contents EN Troubleshooting List of Error Messages Additional OperationsJlip Video Producer Software Starting Jlip Video Producer SoftwareTroubleshooting Major Specifications Index Advanced OperationsInternet homepage Business presentationsVideo journal and postcards Jlip Video Capture Software Video Capture FacilityJlip Control Facility Jlip Video Producer SoftwareControls and Conne Ctors Connect the power cord to an AC outlet Open CoverAttach FIXWhen connected with the camcorder When connected with the Video PrinterPower Connec T Ions Jlip Video Capture Software Section What is video capture software ? What is Jlip ?EN Getting Started Operating EnvironmentInstallation Procedure WindowsPreparation Main Desktop WindowHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Menu bar Main Desktop WindowControl buttons When an image display box is double-clicked Image display areaEach pulldown menu is configured as follows Menu BARVCR operation window Set-upImage data flow Capturing Video ImagesSet-up Capture Mode Step by Step Step by Step CaptureAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Interval Capture Select Interval CaptureSaving Save the Full Image DataPicture Data Format Capture ModeSelecting a Picture Format Counter Value Change Counter ResetModify Capture Point window appears Delete Index Image and Full Image Additional Operation SChange ID Create NEW Folder Open IndexUsing Jlip Video Producer Software Data Open Jlip jlp File window is displayedHOW to Store Jlip Video Producer Software Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskEN Memo Jlip Video Producer Software Section Recorder PlayerVideo printer Installing Jlip Video Producer Software EN Prepare Devices Access Video ProducerSelect Serial Port Select Devices Select RecorderControl-menu box Menu bar Title barMemo Elapsed TimeSetting in/out points EN Basic Oper AtionsOperating camcorder Playback on TV MonitorSelect Scene Start PlaybackEN Basic OP E Ration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file Correcting and cutting the programmed counter dataOverwriting the file Designatecopied Scene to beStore Designated Scene in Memory Designate Scene to be TransferredBasic Operat Ions Selecting a P.AE/EffectSelecting a Fade/Wipe Effect Select P.AE/EFFECTAE/Effect buttons SepiaStore button Position button Strobe Speed button Title bar Power buttonButton Content button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneQuitting the Video Printer window Quitting the Jlip Video Producer windowClick Close Preparation Auto CaptureTo Print Captured Video Data with Video Printer To print only the cut-in scene on the edited tape Select Set-up Function Set Auto CaptureEN Advan CED Oper Ations Connecting other device during operationChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer WindowAccess Record Time Correction Dialog BOX EN Advanced Operat IonsEnter Value Determine ValueRewind Tape to Beginning Reset Counter Counter resetWhen Using the Video Capture Software That power is on Power on all devices System Communication errorClose Check devices - ConfirmMemory full - 99 events MaximumEnter correct value Your selection is not validEN M Ajor Speci Fications Index GV-DS2