JVC GV-DS2 Execute after, Playing back, Not enough disk, Space is available, Communication, Error

Page 41

 

 

EN 41

Message

⬤ Appears when:

Page

 

⬛ Action:

 

 

 

 

Execute after

⬤ Video unit is not in Play mode during Interval

30

 

playing back the

Capture.

 

 

VCR.

⬛ Click "OK", set the video unit to Play and click

 

 

 

"Transfer" again.

 

 

 

 

 

 

Not enough disk

⬤ Remaining disk space is under 1 MB.

—

 

space is available.

⬛ Click "OK" , check disk space and select a drive

 

 

with space available with "Save Image As…".

 

 

 

 

 

 

Communication

⬤ If operation stops after this message appears, turn

 

 

error.

the Capture Docking Station off and then on again.

 

 

 

Images stored in memory will be lost.

 

 

 

⬛ Do not use any other application while JLIP Video

 

 

 

Capture and JLIP Video Producer are running as it

 

 

 

may interfere with communication. Do not click

—

 

 

and move the mouse during data transfer.

 

 

 

 

 

⬤ If your computer's energy saver, battery voltage

 

 

 

indication or screen saver is engaged, the image

 

 

 

data transmission may be interrupted.

 

 

 

⬛ Disengage these functions. Refer to your

 

 

 

computer's instructions manual on details.

 

 

 

 

 

 

Check the capture

⬤ If operation stops after this message appears, turn

—

 

device.

the Capture Docking Station off and then on again.

 

 

Images stored in memory will be lost.

 

 

 

 

 

 

Page 40 Page 42
Image 41
Page 40 Page 42
Contents GV-DS2 It is recommended that you Dear CustomerSome DO’S and DON’TS on the Safe USE of Equipment Do not place the Video Capture Docking Station How to handle a CD-ROMMaintenance Contents EN Additional Operations Troubleshooting List of Error MessagesJlip Video Producer Software Starting Jlip Video Producer SoftwareAdvanced Operations Troubleshooting Major Specifications IndexVideo journal and postcards Business presentationsInternet homepage Video Capture Facility Jlip Video Capture SoftwareJlip Control Facility Jlip Video Producer SoftwareControls and Conne Ctors Open Cover Connect the power cord to an AC outletAttach FIXWhen connected with the Video Printer When connected with the camcorderPower Connec T Ions Jlip Video Capture Software Section What is Jlip ? What is video capture software ?EN Getting Started Operating EnvironmentWindows Installation ProcedureMain Desktop Window PreparationClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Control buttons Main Desktop WindowMenu bar Image display area When an image display box is double-clickedMenu BAR Each pulldown menu is configured as followsSet-up VCR operation windowCapturing Video Images Image data flowStep by Step Capture Set-up Capture Mode Step by StepProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Select Interval Capture Interval CaptureSave the Full Image Data SavingSelecting a Picture Format Capture ModePicture Data Format Modify Capture Point window appears Counter ResetCounter Value Change Change ID Additional Operation SDelete Index Image and Full Image Open Index Create NEW FolderOpen Jlip jlp File window is displayed Using Jlip Video Producer Software DataSave As Jlip jlp File window is displayed HOW to Store Jlip Video Producer Software DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskEN Memo Jlip Video Producer Software Section Video printer PlayerRecorder Installing Jlip Video Producer Software EN Select Serial Port Access Video ProducerPrepare Devices Select Recorder Select DevicesMenu bar Title bar Control-menu boxElapsed Time MemoEN Basic Oper Ations Setting in/out pointsOperating camcorder Playback on TV MonitorStart Playback Select SceneDubbing EN Basic OP E Ration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data Opening a saved fileDesignatecopied Scene to be Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredSelecting a P.AE/Effect Basic Operat IonsSelecting a Fade/Wipe Effect Select P.AE/EFFECTSepia AE/Effect buttonsButton Position button Strobe Speed button Title bar Power buttonStore button Position button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneClick Close Quitting the Jlip Video Producer windowQuitting the Video Printer window To Print Captured Video Data with Video Printer Auto CapturePreparation Select Set-up Function Set Auto Capture To print only the cut-in scene on the edited tapeChanging ID number Connecting other device during operationEN Advan CED Oper Ations Access Device Selection Dialog BOX Access Name Change Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer WindowEN Advanced Operat Ions Access Record Time Correction Dialog BOXEnter Value Determine ValueWhen Using the Video Capture Software Counter resetRewind Tape to Beginning Reset Counter Power on all devices System Communication error That power is onClose Check devices - ConfirmMaximum Memory full - 99 eventsEnter correct value Your selection is not validEN M Ajor Speci Fications Index GV-DS2
Top Page Image Contents