JVC GV-DS2 manual Memo, Elapsed Time

Page 49

1.POWER button

•Turns the device on and off.

•If power is not supplied to the camcorder beforehand, you can not turn the camcorder on and off by clicking this button.

•Some camcorders cannot be turned on and off by clicking this button.

2.COUNTER system

3.Tape counter display

•Displays actual tape position.

ex.

00: 01: 45: 10F

(Hours : Minutes : Seconds : Frames)

4.ID number

•Displays the selected device's ID number.

5.FILE name

•Displays file name after saving the program under a new name.

ex. travel

6.MEMO

•If you wish to add some comment to the file, you can input it.

ex. Europe Tour

7.IN/OUT point display

•You can set up to 99 in/out points per file.

8.SCENE button

•Plays back only one programmed scene so that you can preview it.

•Operates only the camcorder.

9.START button

•Starts editing. Scenes are recorded in scene's numerical order. After starting editing, this button changes to STOP button.

10.ELAPSED TIME

•Displays the total elapsed time of all the programmed scenes.

EN 49

11.Camcorder's operation buttons

•Operate the camcorder.

Stop button

REW/REW Search button

Play button

FF/FF Search button

Pause button

Reverse Slow button

Forward Slow button

•To start Reverse/Forward Slow-motion Search, first click the Pause button and then the Reverse/Forward Slow button.

•Functions your camcorder does not have cannot be performed by the above buttons.

•Click "Window" — "VCR Control" on menubar to call up the "VCR Control" window. You can control the video source unit from this window.

12.IN/OUT point button

•Registers the cut-in and -out points of the scene you want to dub.

13.P.AE/Effect buttons

•Set one of the 5 P.AE/Effects per programmed scene.

•To cancel the selected effect, press the EC (Effect Clear) button.

14.Fade/Wipe Effect buttons

•Set one of the 7 Picture Wipes and 10 Fades/Wipes per scene transition.

•To cancel the selected effect, press the TC (Transition Clear) button.

15.Message display

•Displays the connected device mode, etc.

To exit from the VIDEO PRODUCER window, choose "Exit" from "File".

NOTE:

If you need the "JLIP VIDEO PRODUCER HELP" window, choose "Contents" from "Help".

Image 49

Contents GV-DS2 It is recommended that you Dear CustomerSome DO’S and DON’TS on the Safe USE of Equipment Maintenance How to handle a CD-ROMDo not place the Video Capture Docking Station Contents EN Additional Operations Troubleshooting List of Error MessagesJlip Video Producer Software Starting Jlip Video Producer SoftwareAdvanced Operations Troubleshooting Major Specifications IndexInternet homepage Business presentationsVideo journal and postcards Video Capture Facility Jlip Video Capture SoftwareJlip Control Facility Jlip Video Producer SoftwareControls and Conne Ctors Open Cover Connect the power cord to an AC outletAttach FIXWhen connected with the Video Printer When connected with the camcorderPower Connec T Ions Jlip Video Capture Software Section What is Jlip ? What is video capture software ?EN Getting Started Operating EnvironmentWindows Installation ProcedureMain Desktop Window PreparationClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Menu bar Main Desktop WindowControl buttons Image display area When an image display box is double-clickedMenu BAR Each pulldown menu is configured as followsSet-up VCR operation windowCapturing Video Images Image data flowStep by Step Capture Set-up Capture Mode Step by StepAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Select Interval Capture Interval CaptureSave the Full Image Data SavingPicture Data Format Capture ModeSelecting a Picture Format Counter Value Change Counter ResetModify Capture Point window appears Delete Index Image and Full Image Additional Operation SChange ID Open Index Create NEW FolderOpen Jlip jlp File window is displayed Using Jlip Video Producer Software DataSave As Jlip jlp File window is displayed HOW to Store Jlip Video Producer Software DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskEN Memo Jlip Video Producer Software Section Recorder PlayerVideo printer Installing Jlip Video Producer Software EN Prepare Devices Access Video ProducerSelect Serial Port Select Recorder Select DevicesMenu bar Title bar Control-menu boxElapsed Time MemoEN Basic Oper Ations Setting in/out pointsOperating camcorder Playback on TV MonitorStart Playback Select SceneDubbing EN Basic OP E Ration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data Opening a saved fileDesignatecopied Scene to be Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredSelecting a P.AE/Effect Basic Operat IonsSelecting a Fade/Wipe Effect Select P.AE/EFFECTSepia AE/Effect buttonsStore button Position button Strobe Speed button Title bar Power buttonButton Position button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneQuitting the Video Printer window Quitting the Jlip Video Producer windowClick Close Preparation Auto CaptureTo Print Captured Video Data with Video Printer Select Set-up Function Set Auto Capture To print only the cut-in scene on the edited tapeEN Advan CED Oper Ations Connecting other device during operationChanging ID number Access Device Selection Dialog BOX Access Name Change Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer WindowEN Advanced Operat Ions Access Record Time Correction Dialog BOXEnter Value Determine ValueRewind Tape to Beginning Reset Counter Counter resetWhen Using the Video Capture Software Power on all devices System Communication error That power is onClose Check devices - ConfirmMaximum Memory full - 99 eventsEnter correct value Your selection is not validEN M Ajor Speci Fications Index GV-DS2