JVC GV-DS2 manual Message Appears when Action

Page 40

40

EN

L

IS

T

O

F

ER

R

O

R

ME

S

S

A

GES

Message

⬤ Appears when:

Page

⬛ Action:

COM port is not

⬤ Not connected to COM port set by JLIP Initialize.

20

available.

⬛ Check the COM port number and connector and

retry JLIP initialization.

Connected device

⬤ Connected devices are not turned on.

20, 21

not found.

⬤ Selected COM port is not connected properly.

⬛ Make sure connection is proper and carry out JLIP

initialization. Then turn on this unit and the

connected devices.

Error — Transfer

⬤ Video unit is brought to STOP or ends playback

halted.

during automatic capture.

⬛ Check the auto capture setting.

—

⬤ Full image data (768 x 552 pixels) cannot be

captured if you start auto capture at the beginning

of the tape. Video capture stops if video playback

is stopped.

⬛ Start video capture 20 seconds after the start of the

30

recording.

⬤ Tape is too short to match the preset number of

images or there is a section of non-recorded tape.

⬛ Click "OK", check the tape length and re-enter the

number of images to be captured. Use a fully

recorded tape.

Image 40

Contents GV-DS2 Dear Customer It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment Maintenance How to handle a CD-ROMDo not place the Video Capture Docking Station Contents EN Troubleshooting List of Error Messages Additional OperationsJlip Video Producer Software Starting Jlip Video Producer SoftwareTroubleshooting Major Specifications Index Advanced OperationsInternet homepage Business presentationsVideo journal and postcards Jlip Video Capture Software Video Capture FacilityJlip Control Facility Jlip Video Producer SoftwareControls and Conne Ctors Connect the power cord to an AC outlet Open CoverAttach FIXWhen connected with the camcorder When connected with the Video PrinterPower Connec T Ions Jlip Video Capture Software Section What is video capture software ? What is Jlip ?EN Getting Started Operating EnvironmentInstallation Procedure WindowsPreparation Main Desktop WindowHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Menu bar Main Desktop WindowControl buttons When an image display box is double-clicked Image display areaEach pulldown menu is configured as follows Menu BARVCR operation window Set-upImage data flow Capturing Video ImagesSet-up Capture Mode Step by Step Step by Step CaptureAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Interval Capture Select Interval CaptureSaving Save the Full Image DataPicture Data Format Capture ModeSelecting a Picture Format Counter Value Change Counter ResetModify Capture Point window appears Delete Index Image and Full Image Additional Operation SChange ID Create NEW Folder Open IndexUsing Jlip Video Producer Software Data Open Jlip jlp File window is displayedHOW to Store Jlip Video Producer Software Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskEN Memo Jlip Video Producer Software Section Recorder PlayerVideo printer Installing Jlip Video Producer Software EN Prepare Devices Access Video ProducerSelect Serial Port Select Devices Select RecorderControl-menu box Menu bar Title barMemo Elapsed TimeSetting in/out points EN Basic Oper AtionsOperating camcorder Playback on TV MonitorSelect Scene Start PlaybackEN Basic OP E Ration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file Correcting and cutting the programmed counter dataOverwriting the file Designatecopied Scene to beStore Designated Scene in Memory Designate Scene to be TransferredBasic Operat Ions Selecting a P.AE/EffectSelecting a Fade/Wipe Effect Select P.AE/EFFECTAE/Effect buttons SepiaStore button Position button Strobe Speed button Title bar Power buttonButton Content button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneQuitting the Video Printer window Quitting the Jlip Video Producer windowClick Close Preparation Auto CaptureTo Print Captured Video Data with Video Printer To print only the cut-in scene on the edited tape Select Set-up Function Set Auto CaptureEN Advan CED Oper Ations Connecting other device during operationChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer WindowAccess Record Time Correction Dialog BOX EN Advanced Operat IonsEnter Value Determine ValueRewind Tape to Beginning Reset Counter Counter resetWhen Using the Video Capture Software That power is on Power on all devices System Communication errorClose Check devices - ConfirmMemory full - 99 events MaximumEnter correct value Your selection is not validEN M Ajor Speci Fications Index GV-DS2