JVC GV-DS2 manual Problem Cause

Page 38

38EN TROUBLESHOOTING

NOTE : External noise or disturbance may interfere with the microprocessors built into the JLIP Video Capture Docking Station. If this happens, turn the power off and then turn it on again.

Problem

Cause

Page

JLIP Video Capture Software

⬤ Does the JLIP Video Producer Software or

 

does not work.

the JLIP Movie Player Software run ? The

—

 

JLIP Video Capture Software cannot run

 

 

 

together with it.

 

Operating the camcorder

⬤ If the camcorder is attached to the JLIP

 

(capturing video images

Video Capture Docking Station with the

—

through the computer etc.)

battery pack installed or with the AC Power

is not possible.

Adapter/Charger attached, it is impossible to

 

 

operate the camcorder using the computer.

 

 

 

 

No effect when clicking the

⬤ These buttons do not function.

 

Input Select/Memory

 

—

buttons.

 

 

 

 

 

The video unit does not

⬤ The counter display in the "VCR" operation

 

operate when "Window" —

window turns blue.

25

"VCR" in the menu bar and

⬤ Is your video unit compatible with JLIP ?

 

"VCR" in the "VCR" opera-

Only JLIP-compatible units can be operated.

 

tion window are clicked.

If you are using a JLIP-compatible unit and

 

 

it still won’t work, check to make sure that

12 – 14

 

it is correctly connected.

 

⬤ Is the video unit selected in "Select Unit" ?

21

 

Select correctly.

 

⬤ Initialize JLIP.

20

 

⬤ Make sure the video unit is turned on.

 

 

 

 

The"VCR" operation

⬤ Slow Play in the VCR operation window

25

window display shows a

automatically switches to Play after

 

different operation from

approximately 10 to 20 seconds.

 

what the video unit is

⬤ In some cases, the video unit may continue

 

actually doing.

slow-motion playback even when the

 

 

"VCR" operation window changes from

 

 

Slow Play to Play. Check your video unit’s

 

 

instruction manual for details.

 

 

 

 

On-screen display of video

⬤ It is not possible to capture the on-screen

 

unit is not stored in

display (date, time cord etc.) into the

—

memory.

computer.

 

 

 

 

Counter display appears in

⬤ When capture video data from a powered-

 

the image display box even

on camcorder with no tape loaded, a

 

when there is no tape in the

counter display may appear in the image

—

video unit.

display box. Images corresponding to the

 

 

displayed counter number can no longer be

 

 

caputred.

 

 

 

 

Page 37 Page 39
Image 38
Page 37 Page 39
Contents GV-DS2 Dear Customer It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment Do not place the Video Capture Docking Station How to handle a CD-ROMMaintenance Contents EN Jlip Video Producer Software Troubleshooting List of Error MessagesAdditional Operations Starting Jlip Video Producer SoftwareTroubleshooting Major Specifications Index Advanced OperationsVideo journal and postcards Business presentationsInternet homepage Jlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Jlip Video Producer SoftwareControls and Conne Ctors Attach Connect the power cord to an AC outletOpen Cover FIXWhen connected with the camcorder When connected with the Video PrinterPower Connec T Ions Jlip Video Capture Software Section EN Getting Started What is video capture software ?What is Jlip ? Operating EnvironmentInstallation Procedure WindowsPreparation Main Desktop WindowHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Control buttons Main Desktop WindowMenu bar When an image display box is double-clicked Image display areaEach pulldown menu is configured as follows Menu BARVCR operation window Set-upImage data flow Capturing Video ImagesSet-up Capture Mode Step by Step Step by Step CaptureProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Interval Capture Select Interval CaptureSaving Save the Full Image DataSelecting a Picture Format Capture ModePicture Data Format Modify Capture Point window appears Counter ResetCounter Value Change Change ID Additional Operation SDelete Index Image and Full Image Create NEW Folder Open IndexUsing Jlip Video Producer Software Data Open Jlip jlp File window is displayedHOW to Store Jlip Video Producer Software Data Save As Jlip jlp File window is displayedProblem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counterMessage Appears when Action Playing back ErrorExecute after Not enough diskEN Memo Jlip Video Producer Software Section Video printer PlayerRecorder Installing Jlip Video Producer Software EN Select Serial Port Access Video ProducerPrepare Devices Select Devices Select RecorderControl-menu box Menu bar Title barMemo Elapsed TimeOperating camcorder Setting in/out pointsEN Basic Oper Ations Playback on TV MonitorSelect Scene Start PlaybackPrepare NEW Tape EN Basic OP E Ration SDubbing Start EditingSave File Start SavingEnter File Name Select Floppy Disk DriveOpening a saved file Correcting and cutting the programmed counter dataStore Designated Scene in Memory Overwriting the fileDesignatecopied Scene to be Designate Scene to be TransferredSelecting a Fade/Wipe Effect Basic Operat IonsSelecting a P.AE/Effect Select P.AE/EFFECTAE/Effect buttons SepiaButton Position button Strobe Speed button Title bar Power buttonStore button MULTI-PIX button Content buttonPosition button Strobe Speed buttonPlayback PrintingBring UP Video Printer Window Store SceneClick Close Quitting the Jlip Video Producer windowQuitting the Video Printer window To Print Captured Video Data with Video Printer Auto CapturePreparation To print only the cut-in scene on the edited tape Select Set-up Function Set Auto CaptureChanging ID number Connecting other device during operationEN Advan CED Oper Ations Enter NEW Name SET NEW Name Access Name Change Dialog BOXAccess Device Selection Dialog BOX Return to Video Producer WindowEnter Value Access Record Time Correction Dialog BOXEN Advanced Operat Ions Determine ValueWhen Using the Video Capture Software Counter resetRewind Tape to Beginning Reset Counter Close That power is onPower on all devices System Communication error Check devices - ConfirmEnter correct value Memory full - 99 eventsMaximum Your selection is not validEN M Ajor Speci Fications Index GV-DS2
Top Page Image Contents