JVC GV-DS2 manual Dear Customer, It is recommended that you

Page 2

2EN

Dear Customer,

Thank you for purchasing this VIDEO CAPTURE DOCKING STATION. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of this product.

Using This Instruction Manual

•All major sections and subsections are listed in the Table Of Contents (☞ pg. 5 – 7). •Notes appear after most subsections. Be sure to read these as well.

•Basic and advanced features/operation are separated for easier reference.

It is recommended that you . . .

..... refer to "Controls and Connectors" (☞ pg. 10) and familiarize yourself with connector locations

before use.

..... read thoroughly the Safety Precautions and Safety Instructions that follow. They contain extremely

important information regarding the safe use of your new VIDEO CAPTURE DOCKING STATION.

SAFETY PRECAUTIONS

IMPORTANT

Connection to the mains supply in the United Kingdom.

DO NOT cut off the mains plug from this equipment.

If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover.

If nontheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below: DO NOT make any connection to the Larger Terminal coded E or Green.

The wires in the mains lead are coloured in accordance with the following code:

Blue to N (Neutral) or Black

Brown to L (Live) or Red

If these colours do not correspond with the terminal identifications of your plug, connect as follows:

Blue wire to terminal coded N (Neutral) or coloured black.

Brown wire to terminal coded L (Live) or coloured Red.

If in doubt — consult a competent electrician.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

To prevent shock, do not open the cabinet. No user serviceable parts inside. Refer servicing to qualified personnel.

NOTE:

The rating plate (serial number plate) and safety caution are on the bottom of the

VIDEO CAPTURE DOCKING STATION.

This unit is produced to comply with Standard IEC Publ. 65.

When using the Video Capture Docking Station, use the AA-V90EG or AA-V90EK AC Adapter/Charger (optional or provided with the camcorder).

Page 1 Page 3
Image 2
Page 1 Page 3
Contents GV-DS2 Dear Customer It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment Do not place the Video Capture Docking Station How to handle a CD-ROMMaintenance Contents EN Jlip Video Producer Software Troubleshooting List of Error MessagesAdditional Operations Starting Jlip Video Producer SoftwareTroubleshooting Major Specifications Index Advanced OperationsVideo journal and postcards Business presentationsInternet homepage Jlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Jlip Video Producer SoftwareControls and Conne Ctors Attach Connect the power cord to an AC outletOpen Cover FIXWhen connected with the camcorder When connected with the Video PrinterPower Connec T Ions Jlip Video Capture Software Section EN Getting Started What is video capture software ?What is Jlip ? Operating EnvironmentInstallation Procedure WindowsPreparation Main Desktop WindowHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Control buttons Main Desktop WindowMenu bar When an image display box is double-clicked Image display areaEach pulldown menu is configured as follows Menu BARVCR operation window Set-upImage data flow Capturing Video ImagesSet-up Capture Mode Step by Step Step by Step CaptureProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Interval Capture Select Interval CaptureSaving Save the Full Image DataSelecting a Picture Format Capture ModePicture Data Format Modify Capture Point window appears Counter ResetCounter Value Change Change ID Additional Operation SDelete Index Image and Full Image Create NEW Folder Open IndexUsing Jlip Video Producer Software Data Open Jlip jlp File window is displayedHOW to Store Jlip Video Producer Software Data Save As Jlip jlp File window is displayedProblem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counterMessage Appears when Action Playing back ErrorExecute after Not enough diskEN Memo Jlip Video Producer Software Section Video printer PlayerRecorder Installing Jlip Video Producer Software EN Select Serial Port Access Video ProducerPrepare Devices Select Devices Select RecorderControl-menu box Menu bar Title barMemo Elapsed TimeOperating camcorder Setting in/out pointsEN Basic Oper Ations Playback on TV MonitorSelect Scene Start PlaybackPrepare NEW Tape EN Basic OP E Ration SDubbing Start EditingSave File Start SavingEnter File Name Select Floppy Disk DriveOpening a saved file Correcting and cutting the programmed counter dataStore Designated Scene in Memory Overwriting the fileDesignatecopied Scene to be Designate Scene to be TransferredSelecting a Fade/Wipe Effect Basic Operat IonsSelecting a P.AE/Effect Select P.AE/EFFECTAE/Effect buttons SepiaButton Position button Strobe Speed button Title bar Power buttonStore button MULTI-PIX button Content buttonPosition button Strobe Speed buttonPlayback PrintingBring UP Video Printer Window Store SceneClick Close Quitting the Jlip Video Producer windowQuitting the Video Printer window To Print Captured Video Data with Video Printer Auto CapturePreparation To print only the cut-in scene on the edited tape Select Set-up Function Set Auto CaptureChanging ID number Connecting other device during operationEN Advan CED Oper Ations Enter NEW Name SET NEW Name Access Name Change Dialog BOXAccess Device Selection Dialog BOX Return to Video Producer WindowEnter Value Access Record Time Correction Dialog BOXEN Advanced Operat Ions Determine ValueWhen Using the Video Capture Software Counter resetRewind Tape to Beginning Reset Counter Close That power is onPower on all devices System Communication error Check devices - ConfirmEnter correct value Memory full - 99 eventsMaximum Your selection is not validEN M Ajor Speci Fications Index GV-DS2
Top Page Image Contents