JVC GV-DS2 manual Using Jlip Video Producer Software Data, Open Jlip jlp File window is displayed

Page 36

36EN

JLIPVIDEOPRODUCERSOFTWARE

USING JLIP VIDEO PRODUCER SOFTWARE DATA

The Video Capture Docking Station can capture JLIP Video Producer software data at an edit-in point corresponding to a preset counter number.

File

New Album	Ctrl+N
Open Album	Ctrl+O
Save Album	Ctrl+S
Open JLIP (jlp) File
Open JLIP (jlp) File
Save As JLIP (jlp) File
Save Image As…	Ctrl+A
Exit

Preparation

•Make sure all units are properly connected (☞ p. 12).

•Insert the tape program edited with the Video Producer Software into the video source unit.

•If the data is stored on a floppy disk, load disk into the floppy disk drive.

1 Open the menu bar and click "File" — "Open JLIP (jlp) File".

•The "Open JLIP (jlp) File" window is displayed.

2 Double-click the name of the desired folder (directory) in the Select Directory box.

•If the data is stored on a floppy disk, enter the drive name.

3 Click on the file name to select it.

4 Click "OK".

•The computer monitor displays Scene No., counter number at Edit-in Point, and a blank image box.

5 Open the menu bar and click "Set-up" — "Capture Mode" — "Automatic".

6 Select the data you want to transfer and "Program Capture" and click "OK".

7 Click the "TRANSFER" button.

•The image data scanned by the video source unit is automatically transferred to your computer.

Image 36

Contents GV-DS2 Dear Customer It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment How to handle a CD-ROM MaintenanceDo not place the Video Capture Docking Station Contents EN Troubleshooting List of Error Messages Additional OperationsJlip Video Producer Software Starting Jlip Video Producer SoftwareTroubleshooting Major Specifications Index Advanced OperationsBusiness presentations Internet homepageVideo journal and postcards Jlip Video Capture Software Video Capture FacilityJlip Control Facility Jlip Video Producer SoftwareControls and Conne Ctors Connect the power cord to an AC outlet Open CoverAttach FIXWhen connected with the camcorder When connected with the Video PrinterPower Connec T Ions Jlip Video Capture Software Section What is video capture software ? What is Jlip ?EN Getting Started Operating EnvironmentInstallation Procedure WindowsPreparation Main Desktop WindowHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Main Desktop Window Menu barControl buttons When an image display box is double-clicked Image display areaEach pulldown menu is configured as follows Menu BARVCR operation window Set-upImage data flow Capturing Video ImagesSet-up Capture Mode Step by Step Step by Step CaptureEN V Ideo CA Pture Automatic CaptureProgram Capture Transfer Interval Capture Select Interval CaptureSaving Save the Full Image DataCapture Mode Picture Data FormatSelecting a Picture Format Counter Reset Counter Value ChangeModify Capture Point window appears Additional Operation S Delete Index Image and Full ImageChange ID Create NEW Folder Open IndexUsing Jlip Video Producer Software Data Open Jlip jlp File window is displayedHOW to Store Jlip Video Producer Software Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskEN Memo Jlip Video Producer Software Section Player RecorderVideo printer Installing Jlip Video Producer Software EN Access Video Producer Prepare DevicesSelect Serial Port Select Devices Select RecorderControl-menu box Menu bar Title barMemo Elapsed TimeSetting in/out points EN Basic Oper AtionsOperating camcorder Playback on TV MonitorSelect Scene Start PlaybackEN Basic OP E Ration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file Correcting and cutting the programmed counter dataOverwriting the file Designatecopied Scene to beStore Designated Scene in Memory Designate Scene to be TransferredBasic Operat Ions Selecting a P.AE/EffectSelecting a Fade/Wipe Effect Select P.AE/EFFECTAE/Effect buttons SepiaPosition button Strobe Speed button Title bar Power button Store buttonButton Content button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneQuitting the Jlip Video Producer window Quitting the Video Printer windowClick Close Auto Capture PreparationTo Print Captured Video Data with Video Printer To print only the cut-in scene on the edited tape Select Set-up Function Set Auto CaptureConnecting other device during operation EN Advan CED Oper AtionsChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer WindowAccess Record Time Correction Dialog BOX EN Advanced Operat IonsEnter Value Determine ValueCounter reset Rewind Tape to Beginning Reset CounterWhen Using the Video Capture Software That power is on Power on all devices System Communication errorClose Check devices - ConfirmMemory full - 99 events MaximumEnter correct value Your selection is not validEN M Ajor Speci Fications Index GV-DS2