JVC GV-DS2 manual Access Name Change Dialog BOX, Enter NEW Name SET NEW Name

Page 65

Changing the name of the device

1 ACCESS "NAME CHANGE" DIALOG BOX

Choose "Name Change" from "Set-up" on the JLIP VIDEO PRODUCER window.

•The "Name Change" dialog box appears.

2 SELECT DEVICE

Click on the name of the device and "CHANGE".

•The dialog box to enter new name of the device appears.

3 ENTER NEW NAME

4 SET NEW NAME

Click "OK".

•The message "Device name will be changed." appears.

Clicking "OK" again sets that device name and brings up the "Name Change" dialog box.

5 RETURN TO VIDEO PRODUCER WINDOW

Click "CLOSE".

Name Change

Select the device to change.

VCR

06:VCRCAMERA

CHANGE CLOSE

 

EN 65

Changing the device to use while connecting over two same type devices

1 ACCESS "DEVICE SELECTION" DIALOG BOX

Choose "Device Change" from "Set-up" on the JLIP VIDEO PRODUCER window.

•The "Device Selection" dialog box appears.

2 SELECT DEVICE

Click on the name of the device and "OK".

NOTE:

It is impossible to use two same type devices simultaneously.

Device Selection

 

Select Devices to control.

 

VCR

 

DISCONNECT

OK

06:VCRCAMERA (1)

 

07:VCRCAMERA (2)

CANCEL

 

VIDEO PRINTER

 

DISCONNECT

 

VIDEO PRINTER

CHANGE

Name Change

Enter new name (up to 20 letters).

06 = VCRCAMERA (1)

OK CANCEL

Image 65
Contents GV-DS2 It is recommended that you Dear CustomerSome DO’S and DON’TS on the Safe USE of Equipment Do not place the Video Capture Docking Station How to handle a CD-ROMMaintenance Contents EN Additional Operations Troubleshooting List of Error MessagesJlip Video Producer Software Starting Jlip Video Producer SoftwareAdvanced Operations Troubleshooting Major Specifications IndexVideo journal and postcards Business presentationsInternet homepage Video Capture Facility Jlip Video Capture SoftwareJlip Control Facility Jlip Video Producer SoftwareControls and Conne Ctors Open Cover Connect the power cord to an AC outletAttach FIXWhen connected with the Video Printer When connected with the camcorderPower Connec T Ions Jlip Video Capture Software Section What is Jlip ? What is video capture software ?EN Getting Started Operating EnvironmentWindows Installation ProcedureMain Desktop Window PreparationClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Control buttons Main Desktop WindowMenu bar Image display area When an image display box is double-clickedMenu BAR Each pulldown menu is configured as followsSet-up VCR operation windowCapturing Video Images Image data flowStep by Step Capture Set-up Capture Mode Step by StepProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Select Interval Capture Interval CaptureSave the Full Image Data SavingSelecting a Picture Format Capture ModePicture Data Format Modify Capture Point window appears Counter ResetCounter Value Change Change ID Additional Operation SDelete Index Image and Full Image Open Index Create NEW FolderOpen Jlip jlp File window is displayed Using Jlip Video Producer Software DataSave As Jlip jlp File window is displayed HOW to Store Jlip Video Producer Software DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskEN Memo Jlip Video Producer Software Section Video printer PlayerRecorder Installing Jlip Video Producer Software EN Select Serial Port Access Video ProducerPrepare Devices Select Recorder Select DevicesMenu bar Title bar Control-menu boxElapsed Time MemoEN Basic Oper Ations Setting in/out pointsOperating camcorder Playback on TV MonitorStart Playback Select SceneDubbing EN Basic OP E Ration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data Opening a saved fileDesignatecopied Scene to be Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredSelecting a P.AE/Effect Basic Operat IonsSelecting a Fade/Wipe Effect Select P.AE/EFFECTSepia AE/Effect buttonsButton Position button Strobe Speed button Title bar Power buttonStore button Position button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneClick Close Quitting the Jlip Video Producer windowQuitting the Video Printer window To Print Captured Video Data with Video Printer Auto CapturePreparation Select Set-up Function Set Auto Capture To print only the cut-in scene on the edited tapeChanging ID number Connecting other device during operationEN Advan CED Oper Ations Access Device Selection Dialog BOX Access Name Change Dialog BOXEnter NEW Name SET NEW Name Return to Video Producer WindowEN Advanced Operat Ions Access Record Time Correction Dialog BOXEnter Value Determine ValueWhen Using the Video Capture Software Counter resetRewind Tape to Beginning Reset Counter Power on all devices System Communication error That power is onClose Check devices - ConfirmMaximum Memory full - 99 eventsEnter correct value Your selection is not validEN M Ajor Speci Fications Index GV-DS2