Panasonic AWRP120GJ Speed, Scope Mode a, Scope settings and recalled items Recalled item Setting

Page 15

Operating preset memory (PMEM) (continued)

Setting the operation items for when preset memory is recalled (PRESET SCOPE)

You can select whether to recall all or only some of the settings registered to preset memory.

Note

zzThis function is enabled when AW-HE50, AW-HE60, or AW-HE120 is selected.

1.Press one of the camera selection buttons [CAMERA SELECT/GROUP SELECT] to select the remote camera to be operated..

2.Press the PMEM button to turn on its indicator..

3.Press the MEM SETTING button to turn on its indicator..

The setting of the selected remote camera is displayed.

SPEED : 30

SCOPE : MODE A

4.Turn the F2 dial to select a setting for the “SCOPE” item from MODE A to MODE C, and then press the F2 dial to confirm the selection..

The setting of the remote camera is changed. This is applied the next time the preset is recalled.

<SCOPE settings and recalled items>

 

 

Recalled item

 

Setting

Pan, tilt, zoom,

 

White balance

Iris

adjustment

 

and focus

 

 

value

 

 

 

MODE A

√

√

√

MODE B

√

√

—

MODE C

√

—

—

√: Recalled —: Not recalled

Note

zzMODE A to MODE C are not registered to the remote camera preset memory or the unit. The settings become the common settings for when preset memory is recalled, and the same settings are applied regardless of which preset number is selected.

Registering the speed at which to move to the position set in the preset memory

(PRESET SPEED)

The unit registers the speed (PRESET SPEED) at which to move to the set position when preset memory is recalled to each preset number. When a preset is recalled, the unit sets PRESET SPEED on the remote camera and the remote camera moves to the preset position at the speed set for PRESET SPEED.

Performing operation at a different speed for each preset memory enables video to be played at a variety of speeds.

Notes

zzThe movement speed registered in the procedure below is registered to the corresponding camera number, and is not registered to the preset memory of the remote camera. Therefore, if the preset memory is recalled from a controller other than this unit on which the movement speed was registered, movement will be at a different speed even in the case of the same preset number.

zzWhen the connection type or connection destination IP address is changed with CTRL TYPE menu [36], AUTO IP menu [37], or SWAP IP menu [38], PRESET SPEED set for the corresponding camera number is initialized.

1.Press one of the camera selection buttons [CAMERA SELECT/GROUP SELECT] to select the remote camera to be operated..

2.Press the PMEM button to turn on its indicator..

3.Press the MEM STORE button to turn on its indicator..

4.Press the MEM SETTING button to turn on its indicator..

The setting of the selected remote camera is displayed.

SPEED : 30

SCOPE : MODE A

5. Turn the F1 dial to select the setting of the “SPEED” item, and then press the F1 dial to confirm the selection..

The following shows the relationship between the set value and the speed at which the remote camera moves to the set position when preset memory is recalled.

1 30

SlowFast

6.Hold down a number button to specify the preset number to register..

The current remote camera settings are registered to preset memory, and PRESET SPEED is registered to the unit.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operating Instructions Illustrations and screen images in this manual About trademarks and registered trademarksCopyrights AbbreviationsContents How to turn on the power of the remote cameras How to turn on and off the power of the remote cameras„„Turning off the power of all the cameras How to turn off the power of the remote camerasTurning off the power one camera at a time Turning off the power of multiple camerasBars button Making image adjustments for the selected remote cameraColor adjustment section ZzR and B pedestalAutomatically adjusting the white balance Setting the gainSetting the pedestal Setting the white balanceAutomatically adjusting the black balance Setting the black balanceManually adjusting the white balance R and B gain settings Auto tracking white adjustment ATWSetting the shutter speed Setting the detailAdjusting the shutter speed Setting the shutter modeAW‑HE50 Setting the shooting mode Scene 1 to SceneSelecting an ND filter with the User buttons User 1 to User Setting an ND filterND Filter ND1Operate the OSD menu Hold down the Camera OSD button to turn on its indicatorHold down the Camera OSD button to turn off its indicator Operating the osd menu of a remote cameraPmem Operating preset memory PmemZzLighting of number button indicators ZzChanging pagesRegistering preset memory Store Recalling preset memory RecallDeleting preset memory Delete Iris Scope Mode aScope settings and recalled items Recalled item Setting SpeedPM GRP1 Mode Separate Operating preset memory groups Pmem GroupSetting the operation mode SEPARATE/ ALL Creating preset memory groupsPressing a button to recall a preset memory group Recalling preset memory groupsRegistering the preset memory to recall when in ALL mode PM GRP1 Mode ALL3m50s Remained Operating tracing memory TmemRegistering tracing memory Store CAM1 TmemPress Stop button Recalling tracing memory RecallStandby Recall RecallingRestoring Restoring tracing memory RestoreStandby Restore Deleting tracing memory DeleteRecalled item Setting Setting the items to recall when recalling tracing memoryT Curv Configuring the remote camera operation settingsSetting the PAN/TILT lever inclination and speed „„Operation of Speed dialSetting the zooming direction Setting the pan, tilt, zoom, and focus operation directionsSetting the panning direction Setting the tilting directionSpeed with Z Off Setting the minimum lens zoom start speedSetting the focusing direction MIN SpeedSetting procedure „„When AW-HE50, AW-HE60, or AW-HE120„„When other remote camera Controlling a heater or fan Returning a remote cameras to its home positionControlling a defroster Controlling a wiperButton indicator on or blinking Configuring the unit operation settingsEnabling or disabling operation with the Enable buttons Press the Enable buttonEnabling or disabling menu operation Disabling Menu operationEnabling Menu operation LCD Backligh T Off Switching the focus operation and iris operationSetting the LCD panel backlight FOCUS/IRIS StandardUSER1 Assigning functions to the User buttonsINPUT1 Setting linking with a switcher„„Settings for the connection between unit and switcher „„Settings on the switcherBUS AUX Buscont functionEnabling or disabling the Buscont function BuscontEnabling or disabling the Camera Select function Setting the Focus Assist functionFocus Assist function Camera Select view functionT/Z Control CAM Tally IP functionEnabling or disabling the Tally IP function TallyipCAM INF Caminfformat CAM INF AlarmCAM INF function Enabling or disabling the CAM INF functionLoad Memory card operationsZzMemory cards SaveSaving data to a memory card Save Initializing a memory card InitDeleting the files saved to a memory card Delete Loading data from a memory card LoadTally OUT Tally settings„„Settings on remote cameras Tally IN1Checking alarm information Displaying alarm informationPower No Alarm ALL Setup Returning the unit to the factory default state InitializeSetting items stored on the unit SetupReturning the unit to the factory default state Setting items stored on the unitInitialize ALL AW‑RP120 CAM OUT1 Registering camera numbers to CAM OUT1 to CAM OUT10Installing the software Setup SoftwareEnter the IP addresses in the IP address boxes Registering the unit in Setup SoftwareSettings for connecting with the remote cameras and switcher Displaying the Setting tab Initializing the IP addresses Executing auto IP settingAcquiring the connection settings Changing the connection destination IP addressesSetting user authentication Enter the same password as above in the Retype password boxClicking Refresh clears the user name and password Campinp POS Campinp ModeOperations of AW-HE2 Campinp CTLDial/button Setting item Remote camera Table of setting items dedicated dials and buttonsTable of setting items menus VideoFilm Table of setting items menus SW Setup SW CTL Operation lock When starting up and switching camera groupsPreset memory MessagesIP connection settings Memory cardMessages Xx Menu IndexIndex プロフェッショナルAVビジネスユニット
Top Page Image Contents