Panasonic AWRP120GJ Operating preset memory groups Pmem Group, Creating preset memory groups

Page 16

Operating preset memory groups (PMEM GROUP)

The unit allows you register up to four “preset memory groups” created by selecting one preset memory for each of multiple remote cameras. Pressing any of the PM GRP 1 to PM GRP 4 buttons simultaneously recalls all preset memory registered to the corresponding preset memory group.

The following setting procedures use the example of setting PMEM GROUP1 but the setting procedures are the same for PMEM GROUP2 to PMEM GROUP4.

Open the following menus and configure the settings.

<Preset memory groups and menu numbers>

Preset memory group

Menu

 

 

PMEM GROUP1

PM GRP1 menu [31]

PMEM GROUP2

PM GRP2 menu [32]

PMEM GROUP3

PM GRP3 menu [33]

PMEM GROUP4

PM GRP4 menu [34]

Setting the operation mode (SEPARATE/ ALL)

1. Press the MENU button to turn on its indicator..

2. Open PM GRP1 menu [31]..

1.PM GRP1 MODE SEPARATE

3.Turn the F1 dial to display the “1.  PM GRP1 MODE” item..

4.Turn the F2 dial to select the operation mode, and then press the F2 dial to confirm the selection..

OFF

: Disables group creation.

 

Even if you press any of the PM GRP1 to PM GRP4

 

buttons, a preset memory group will not be recalled.

SEPARATE

: Allows you to create a group by selecting a different

 

preset number from each remote camera.

 

Up to ten preset numbers can be registered to one

 

group.

ALL

: Allows you to create a group by selecting the same

 

preset number from each remote camera.

 

One preset number for each of all the remote

 

cameras registered to the unit can be registered to

 

one group.

Creating preset memory groups

Registering the preset memory to recall when in SEPARATE mode

1. Press the MENU button to turn on its indicator..

2. Open PM GRP1 menu [31]..

1.PM GRP1 MODE SEPARATE

3.Turn the F1 dial to display the “2.  PM GRP1 1/10” item..

2.PM GRP1 1/10 NoAsgn ——————

4.Turn the F2 dial to set the camera number and preset number to register to PMEM GROUP1..

If you turn the F2 dial to select the camera number and then press the F2 dial to confirm the selection, you will then be able to select the preset number.

Set the preset number in the same way as the camera number.

2.PM GRP1 1/10 CAM001 PRE001

Camera number Preset number

Camera number : Select from NoAsgn and CAM001 to CAM100. When “NoAsgn” is set, preset memory is not registered.

Preset number : Select from PRE001 to PRE100.

5.Turn the F1 dial to display the “3.  PM GRP1 2/10” to “11.  PM GRP1 10/10” items..

6.Register the camera numbers and preset numbers.. zzConfigure the settings in the same way as step 4.

zzUp to ten preset memory can be registered to one group.

Note

zzDo not set the same camera number two or more times for one preset memory group.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operating Instructions About trademarks and registered trademarks CopyrightsAbbreviations Illustrations and screen images in this manualContents How to turn on and off the power of the remote cameras How to turn on the power of the remote camerasHow to turn off the power of the remote cameras Turning off the power one camera at a timeTurning off the power of multiple cameras „„Turning off the power of all the camerasMaking image adjustments for the selected remote camera Color adjustment sectionZzR and B pedestal Bars buttonSetting the gain Setting the pedestalSetting the white balance Automatically adjusting the white balanceSetting the black balance Manually adjusting the white balance R and B gain settingsAuto tracking white adjustment ATW Automatically adjusting the black balanceSetting the detail Adjusting the shutter speedSetting the shutter mode Setting the shutter speedSetting the shooting mode Scene 1 to Scene AW‑HE50Setting an ND filter ND FilterND1 Selecting an ND filter with the User buttons User 1 to UserHold down the Camera OSD button to turn on its indicator Hold down the Camera OSD button to turn off its indicatorOperating the osd menu of a remote camera Operate the OSD menuOperating preset memory Pmem ZzLighting of number button indicatorsZzChanging pages PmemRecalling preset memory Recall Registering preset memory StoreDeleting preset memory Delete Scope Mode a Scope settings and recalled items Recalled item SettingSpeed IrisOperating preset memory groups Pmem Group Setting the operation mode SEPARATE/ ALLCreating preset memory groups PM GRP1 Mode SeparateRecalling preset memory groups Registering the preset memory to recall when in ALL modePM GRP1 Mode ALL Pressing a button to recall a preset memory groupOperating tracing memory Tmem Registering tracing memory StoreCAM1 Tmem 3m50s RemainedRecalling tracing memory Recall Standby RecallRecalling Press Stop buttonRestoring tracing memory Restore Standby RestoreDeleting tracing memory Delete RestoringSetting the items to recall when recalling tracing memory Recalled item SettingConfiguring the remote camera operation settings Setting the PAN/TILT lever inclination and speed„„Operation of Speed dial T CurvSetting the pan, tilt, zoom, and focus operation directions Setting the panning directionSetting the tilting direction Setting the zooming directionSetting the minimum lens zoom start speed Setting the focusing directionMIN Speed Speed with Z Off„„When AW-HE50, AW-HE60, or AW-HE120 Setting procedure„„When other remote camera Returning a remote cameras to its home position Controlling a defrosterControlling a wiper Controlling a heater or fanConfiguring the unit operation settings Enabling or disabling operation with the Enable buttonsPress the Enable button Button indicator on or blinkingDisabling Menu operation Enabling or disabling menu operationEnabling Menu operation Switching the focus operation and iris operation Setting the LCD panel backlightFOCUS/IRIS Standard LCD Backligh T OffAssigning functions to the User buttons USER1Setting linking with a switcher „„Settings for the connection between unit and switcher„„Settings on the switcher INPUT1Buscont function Enabling or disabling the Buscont functionBuscont BUS AUXSetting the Focus Assist function Focus Assist functionCamera Select view function Enabling or disabling the Camera Select functionTally IP function Enabling or disabling the Tally IP functionTallyip T/Z Control CAMCaminfformat CAM INF Alarm CAM INF functionEnabling or disabling the CAM INF function CAM INFMemory card operations ZzMemory cardsSave LoadInitializing a memory card Init Saving data to a memory card SaveLoading data from a memory card Load Deleting the files saved to a memory card DeleteTally settings „„Settings on remote camerasTally IN1 Tally OUTDisplaying alarm information Checking alarm informationPower No Alarm Returning the unit to the factory default state Initialize Setting items stored on the unitSetup ALL SetupSetting items stored on the unit Returning the unit to the factory default stateInitialize ALL AW‑RP120 Registering camera numbers to CAM OUT1 to CAM OUT10 CAM OUT1Setup Software Installing the softwareRegistering the unit in Setup Software Enter the IP addresses in the IP address boxesSettings for connecting with the remote cameras and switcher Displaying the Setting tab Executing auto IP setting Acquiring the connection settingsChanging the connection destination IP addresses Initializing the IP addressesEnter the same password as above in the Retype password box Setting user authenticationClicking Refresh clears the user name and password Campinp Mode Operations of AW-HE2Campinp CTL Campinp POSTable of setting items dedicated dials and buttons Dial/button Setting item Remote cameraVideo Table of setting items menusFilm Table of setting items menus SW Setup SW CTL When starting up and switching camera groups Preset memoryMessages Operation lockMemory card IP connection settingsMessages Index Xx MenuIndex プロフェッショナルAVビジネスユニット
Top Page Image Contents