Panasonic AWRP120GJ operating instructions Operating preset memory Pmem, ZzChanging pages

Page 13

Operating preset memory (PMEM)

The preset memory of a remote camera can be operated from the unit. The following settings that you have adjusted in advance can be stored in preset memory.

zzPan/tilt positions zzLens iris settings (manual iris only)

zzZoom positions zzWhite balance settings zzFocus positions

Notes

zzIf the MEM ENABLE button indicator is off, preset memory operation is not possible. Press the button to turn on its indicator and then perform operation.

zzPreset numbers PMEM 1 to 10 are also used as start positions when recalling tracing memory. Preset data may be overwritten or deleted by tracing memory operation.

zzThe number of preset memory and data that can be registered differ depending on the remote camera.

For details, check the operating instructions for the corresponding model.

MEM SETTING button

MEM ENABLE button

MEM DELETE button

PMEM button

MEM STORE button

PMEM PAGE

indicators

PMEM PAGE

button

Number buttons

[1] to [50]

zzChanging pages

Press one of the number buttons [1] to [50] to directly select any of the 50 preset memory.

Furthermore, pressing the PMEM PAGE button to change pages allows you to operate up to 100 preset memory for each camera.

Button indicator on

Button indicator on

Press the PMEM

PAGE button

Page 1 selected

 

Page 2 selected

<Preset numbers and registered pages>

 

 

Preset number

Page number

Number button

PMEM 1 to PMEM 50

Page 1

 

[1] to [50]

PMEM 51 to PMEM 100

Page 2

 

 

 

Example: When specifying preset number “PMEM 51”

1.Press the PMEM page button to select Page 2.

2.Press number button [1].

zzLighting of number button indicators

The lighting method of the number buttons differs depending on the remote camera or pan-tilt head that the unit is controlling.

<Lighting method of number button indicators>

Remote cameras and

Lighting method of number button

pan-tilt heads

indicators

AW-HE50, AW-HE60,

The indicators of the number buttons with

AW-HE120

preset memory registered turn on.

AW-HE100, AW-PH360,

The indicator of the number button that

AW-PH405, AW-PH650,

was last pressed turns on.

AW-PH400

However, when preset memory is deleted

 

in DELETE mode, all of the number

 

buttons turn off.

13

Image 13
Contents Operating Instructions Copyrights About trademarks and registered trademarksAbbreviations Illustrations and screen images in this manualContents How to turn on the power of the remote cameras How to turn on and off the power of the remote camerasTurning off the power one camera at a time How to turn off the power of the remote camerasTurning off the power of multiple cameras „„Turning off the power of all the camerasColor adjustment section Making image adjustments for the selected remote cameraZzR and B pedestal Bars buttonSetting the pedestal Setting the gainSetting the white balance Automatically adjusting the white balanceManually adjusting the white balance R and B gain settings Setting the black balanceAuto tracking white adjustment ATW Automatically adjusting the black balanceAdjusting the shutter speed Setting the detailSetting the shutter mode Setting the shutter speedAW‑HE50 Setting the shooting mode Scene 1 to SceneND Filter Setting an ND filterND1 Selecting an ND filter with the User buttons User 1 to UserHold down the Camera OSD button to turn off its indicator Hold down the Camera OSD button to turn on its indicatorOperating the osd menu of a remote camera Operate the OSD menuZzLighting of number button indicators Operating preset memory PmemZzChanging pages PmemRecalling preset memory Recall Registering preset memory StoreDeleting preset memory Delete Scope settings and recalled items Recalled item Setting Scope Mode aSpeed IrisSetting the operation mode SEPARATE/ ALL Operating preset memory groups Pmem GroupCreating preset memory groups PM GRP1 Mode SeparateRegistering the preset memory to recall when in ALL mode Recalling preset memory groupsPM GRP1 Mode ALL Pressing a button to recall a preset memory groupRegistering tracing memory Store Operating tracing memory TmemCAM1 Tmem 3m50s RemainedStandby Recall Recalling tracing memory RecallRecalling Press Stop buttonStandby Restore Restoring tracing memory RestoreDeleting tracing memory Delete RestoringRecalled item Setting Setting the items to recall when recalling tracing memorySetting the PAN/TILT lever inclination and speed Configuring the remote camera operation settings„„Operation of Speed dial T CurvSetting the panning direction Setting the pan, tilt, zoom, and focus operation directionsSetting the tilting direction Setting the zooming directionSetting the focusing direction Setting the minimum lens zoom start speedMIN Speed Speed with Z Off„„When AW-HE50, AW-HE60, or AW-HE120 Setting procedure„„When other remote camera Controlling a defroster Returning a remote cameras to its home positionControlling a wiper Controlling a heater or fanEnabling or disabling operation with the Enable buttons Configuring the unit operation settingsPress the Enable button Button indicator on or blinkingDisabling Menu operation Enabling or disabling menu operationEnabling Menu operation Setting the LCD panel backlight Switching the focus operation and iris operationFOCUS/IRIS Standard LCD Backligh T OffUSER1 Assigning functions to the User buttons„„Settings for the connection between unit and switcher Setting linking with a switcher„„Settings on the switcher INPUT1Enabling or disabling the Buscont function Buscont functionBuscont BUS AUXFocus Assist function Setting the Focus Assist functionCamera Select view function Enabling or disabling the Camera Select functionEnabling or disabling the Tally IP function Tally IP functionTallyip T/Z Control CAMCAM INF function Caminfformat CAM INF AlarmEnabling or disabling the CAM INF function CAM INFZzMemory cards Memory card operationsSave LoadSaving data to a memory card Save Initializing a memory card InitDeleting the files saved to a memory card Delete Loading data from a memory card Load„„Settings on remote cameras Tally settingsTally IN1 Tally OUTDisplaying alarm information Checking alarm informationPower No Alarm Setting items stored on the unit Returning the unit to the factory default state InitializeSetup ALL SetupSetting items stored on the unit Returning the unit to the factory default stateInitialize ALL AW‑RP120 CAM OUT1 Registering camera numbers to CAM OUT1 to CAM OUT10Installing the software Setup SoftwareEnter the IP addresses in the IP address boxes Registering the unit in Setup SoftwareSettings for connecting with the remote cameras and switcher Displaying the Setting tab Acquiring the connection settings Executing auto IP settingChanging the connection destination IP addresses Initializing the IP addressesEnter the same password as above in the Retype password box Setting user authenticationClicking Refresh clears the user name and password Operations of AW-HE2 Campinp ModeCampinp CTL Campinp POSDial/button Setting item Remote camera Table of setting items dedicated dials and buttonsVideo Table of setting items menusFilm Table of setting items menus SW Setup SW CTL Preset memory When starting up and switching camera groupsMessages Operation lockMemory card IP connection settingsMessages Xx Menu IndexIndex プロフェッショナルAVビジネスユニット