Panasonic AWRP120GJ Executing auto IP setting, Changing the connection destination IP addresses

Page 49

Setup Software (continued)

Executing auto IP setting

You can execute “auto IP setting” of the unit from Setup Software.

„„Updating the IP addresses of the remote cameras and switcher automatically from the unit

1.Click [RENEW]..

The IP addresses are displayed for the link target camera numbers and switcher.

zzWhen [CANCEL] is clicked, the original settings are restored.

2.Click [SET]..

The displayed IP addresses are set on the remote cameras and switcher.

„„Leaving the IP addresses set on the remote cameras and switcher unchanged and automatically updating the connection destination IP addresses set on the unit

1.Click [KEEP]..

The IP addresses set for the remote cameras and switcher are displayed for the link target camera numbers and switcher. zzWhen [CANCEL] is clicked, the original settings are restored.

2.Click [SET]..

The displayed IP addresses are set as the connection destination IP addresses of the unit.

Changing the connection destination IP addresses

Set the IP addresses that are the connection destinations of the unit.

1.Directly enter the IP address of the device concerned in the [IP Address] box..

2.Click [SET]..

The new IP address is applied.

Swapping the remote cameras that are connection destinations

Swap the remote cameras set as connection destinations between two camera numbers.

1.Click of the “SWAP CAMERA” item..

Camera numbers “C001” to “C100” appear in the list box.

Select the camera number with which you want to make the swap from this list.

2.Click [SET]..

The remote cameras set as connection destinations are swapped between the two camera numbers.

Setting the image inputs of the switcher that correspond to camera numbers

Set the image input of the switcher that will correspond to each camera number.

1.Click of the “SW INPUT” item..

Switcher image inputs “INPUT1” to “INPUT100” appear.

Set the image input that will associated with each camera number.

2.Click [SET]..

The image input of the switcher is associated with the camera number.

Initializing the IP addresses

Clicking [ALL CLEAR] initializes the connection settings that are set on the unit.

Acquiring the connection settings

Clicking [REFRESH] acquires the connection settings for the unit selected in the setting target selection list box, and refreshes the display.

49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Operating Instructions Copyrights About trademarks and registered trademarksAbbreviations Illustrations and screen images in this manualContents How to turn on the power of the remote cameras How to turn on and off the power of the remote camerasTurning off the power one camera at a time How to turn off the power of the remote camerasTurning off the power of multiple cameras „„Turning off the power of all the camerasColor adjustment section Making image adjustments for the selected remote cameraZzR and B pedestal Bars buttonSetting the pedestal Setting the gainSetting the white balance Automatically adjusting the white balanceManually adjusting the white balance R and B gain settings Setting the black balanceAuto tracking white adjustment ATW Automatically adjusting the black balanceAdjusting the shutter speed Setting the detailSetting the shutter mode Setting the shutter speedAW‑HE50 Setting the shooting mode Scene 1 to SceneND Filter Setting an ND filterND1 Selecting an ND filter with the User buttons User 1 to UserHold down the Camera OSD button to turn off its indicator Hold down the Camera OSD button to turn on its indicatorOperating the osd menu of a remote camera Operate the OSD menuZzLighting of number button indicators Operating preset memory PmemZzChanging pages PmemRecalling preset memory Recall Registering preset memory StoreDeleting preset memory Delete Scope settings and recalled items Recalled item Setting Scope Mode aSpeed IrisSetting the operation mode SEPARATE/ ALL Operating preset memory groups Pmem GroupCreating preset memory groups PM GRP1 Mode SeparateRegistering the preset memory to recall when in ALL mode Recalling preset memory groupsPM GRP1 Mode ALL Pressing a button to recall a preset memory groupRegistering tracing memory Store Operating tracing memory TmemCAM1 Tmem 3m50s RemainedStandby Recall Recalling tracing memory RecallRecalling Press Stop buttonStandby Restore Restoring tracing memory RestoreDeleting tracing memory Delete RestoringRecalled item Setting Setting the items to recall when recalling tracing memorySetting the PAN/TILT lever inclination and speed Configuring the remote camera operation settings„„Operation of Speed dial T CurvSetting the panning direction Setting the pan, tilt, zoom, and focus operation directionsSetting the tilting direction Setting the zooming directionSetting the focusing direction Setting the minimum lens zoom start speedMIN Speed Speed with Z Off„„When AW-HE50, AW-HE60, or AW-HE120 Setting procedure„„When other remote camera Controlling a defroster Returning a remote cameras to its home positionControlling a wiper Controlling a heater or fanEnabling or disabling operation with the Enable buttons Configuring the unit operation settingsPress the Enable button Button indicator on or blinkingDisabling Menu operation Enabling or disabling menu operationEnabling Menu operation Setting the LCD panel backlight Switching the focus operation and iris operationFOCUS/IRIS Standard LCD Backligh T OffUSER1 Assigning functions to the User buttons„„Settings for the connection between unit and switcher Setting linking with a switcher„„Settings on the switcher INPUT1Enabling or disabling the Buscont function Buscont functionBuscont BUS AUXFocus Assist function Setting the Focus Assist functionCamera Select view function Enabling or disabling the Camera Select functionEnabling or disabling the Tally IP function Tally IP functionTallyip T/Z Control CAMCAM INF function Caminfformat CAM INF AlarmEnabling or disabling the CAM INF function CAM INFZzMemory cards Memory card operationsSave LoadSaving data to a memory card Save Initializing a memory card InitDeleting the files saved to a memory card Delete Loading data from a memory card Load„„Settings on remote cameras Tally settingsTally IN1 Tally OUTDisplaying alarm information Checking alarm informationPower No Alarm Setting items stored on the unit Returning the unit to the factory default state InitializeSetup ALL SetupSetting items stored on the unit Returning the unit to the factory default stateInitialize ALL AW‑RP120 CAM OUT1 Registering camera numbers to CAM OUT1 to CAM OUT10Installing the software Setup SoftwareEnter the IP addresses in the IP address boxes Registering the unit in Setup SoftwareSettings for connecting with the remote cameras and switcher Displaying the Setting tab Acquiring the connection settings Executing auto IP settingChanging the connection destination IP addresses Initializing the IP addressesEnter the same password as above in the Retype password box Setting user authenticationClicking Refresh clears the user name and password Operations of AW-HE2 Campinp ModeCampinp CTL Campinp POSDial/button Setting item Remote camera Table of setting items dedicated dials and buttonsVideo Table of setting items menusFilm Table of setting items menus SW Setup SW CTL Preset memory When starting up and switching camera groupsMessages Operation lockMemory card IP connection settingsMessages Xx Menu IndexIndex プロフェッショナルAVビジネスユニット
Top Page Image Contents