Panasonic AWRP120GJ Setting the minimum lens zoom start speed, Setting the focusing direction

Page 24

Configuring the remote camera operation settings (continued)

Setting the focusing direction

Set the focusing operation of the lens in response to the operation of the FOCUS dial.

1. Press the MENU button..

2. Open FOCUS DIRECTION menu [29]..

3. Turn the F1 dial to display the camera number for which to configure the setting..

1.CAM1

NORMAL

Setting the minimum lens zoom start speed

Correct the zoom control amount to send from the unit so that the lens zoom starts to move smoothly when the zoom button is pressed in slowly.

1.Press the MENU button..

2.Open PTZ ADJUST menu [30]..

3.Turn the F1 dial to display the “1.  Z MIN SPEED” item..

1.Z MIN SPEED

Off

4.Turn the F2 dial to select “NORMAL” or “REVERSE”, and then press the F2 dial to confirm the selection..

NORMAL

: The focus moves toward the far end when the

 

FOCUS dial is turned clockwise, and toward the near

 

end when the dial is turned counterclockwise.

REVERSE

: Operation is in the opposite direction to NORMAL.

4.Turn the F2 dial to select the correction amount, and then press the F2 dial to confirm the selection.. zzThe lowest correction amount is “1”, and the highest is “8”.

No correction is made with the “Off” setting.

While observing the images on a monitor, press the ZOOM button slowly and check whether the lens zoom starts moving smoothly.

Setting the speed of the pan and tilt operations for telephoto shooting

During telephoto shooting, the remote camera’s pan and tilt operations are slowed down to make positioning easier.

1.Press the MENU button..

2.Open PTZ ADJUST menu [30]..

3.Turn the F1 dial to display the “2.  SPEED WITH Z” item..

2.SPEED WITH Z Off

4.Turn the F2 dial to select “On” or “Off”, and then press the F2 dial to confirm the selection..

On

: The pan and tilt operations during telephoto shooting are

 

slow.

Off

: Movement is at normal speed.

Note

zzThis function is enabled when AW‑HE50, AW‑HE60, or AW‑HE120 is connected.

24

Image 24
Contents Operating Instructions About trademarks and registered trademarks CopyrightsAbbreviations Illustrations and screen images in this manualContents How to turn on and off the power of the remote cameras How to turn on the power of the remote camerasHow to turn off the power of the remote cameras Turning off the power one camera at a timeTurning off the power of multiple cameras „„Turning off the power of all the camerasMaking image adjustments for the selected remote camera Color adjustment sectionZzR and B pedestal Bars buttonSetting the gain Setting the pedestalSetting the white balance Automatically adjusting the white balanceSetting the black balance Manually adjusting the white balance R and B gain settingsAuto tracking white adjustment ATW Automatically adjusting the black balanceSetting the detail Adjusting the shutter speedSetting the shutter mode Setting the shutter speedSetting the shooting mode Scene 1 to Scene AW‑HE50Setting an ND filter ND FilterND1 Selecting an ND filter with the User buttons User 1 to UserHold down the Camera OSD button to turn on its indicator Hold down the Camera OSD button to turn off its indicatorOperating the osd menu of a remote camera Operate the OSD menuOperating preset memory Pmem ZzLighting of number button indicatorsZzChanging pages PmemRegistering preset memory Store Recalling preset memory RecallDeleting preset memory Delete Scope Mode a Scope settings and recalled items Recalled item SettingSpeed IrisOperating preset memory groups Pmem Group Setting the operation mode SEPARATE/ ALLCreating preset memory groups PM GRP1 Mode SeparateRecalling preset memory groups Registering the preset memory to recall when in ALL modePM GRP1 Mode ALL Pressing a button to recall a preset memory groupOperating tracing memory Tmem Registering tracing memory StoreCAM1 Tmem 3m50s RemainedRecalling tracing memory Recall Standby RecallRecalling Press Stop buttonRestoring tracing memory Restore Standby RestoreDeleting tracing memory Delete RestoringSetting the items to recall when recalling tracing memory Recalled item SettingConfiguring the remote camera operation settings Setting the PAN/TILT lever inclination and speed„„Operation of Speed dial T CurvSetting the pan, tilt, zoom, and focus operation directions Setting the panning directionSetting the tilting direction Setting the zooming directionSetting the minimum lens zoom start speed Setting the focusing directionMIN Speed Speed with Z OffSetting procedure „„When AW-HE50, AW-HE60, or AW-HE120„„When other remote camera Returning a remote cameras to its home position Controlling a defrosterControlling a wiper Controlling a heater or fanConfiguring the unit operation settings Enabling or disabling operation with the Enable buttonsPress the Enable button Button indicator on or blinkingEnabling or disabling menu operation Disabling Menu operationEnabling Menu operation Switching the focus operation and iris operation Setting the LCD panel backlightFOCUS/IRIS Standard LCD Backligh T OffAssigning functions to the User buttons USER1Setting linking with a switcher „„Settings for the connection between unit and switcher„„Settings on the switcher INPUT1Buscont function Enabling or disabling the Buscont functionBuscont BUS AUXSetting the Focus Assist function Focus Assist functionCamera Select view function Enabling or disabling the Camera Select functionTally IP function Enabling or disabling the Tally IP functionTallyip T/Z Control CAMCaminfformat CAM INF Alarm CAM INF functionEnabling or disabling the CAM INF function CAM INFMemory card operations ZzMemory cardsSave LoadInitializing a memory card Init Saving data to a memory card SaveLoading data from a memory card Load Deleting the files saved to a memory card DeleteTally settings „„Settings on remote camerasTally IN1 Tally OUTChecking alarm information Displaying alarm informationPower No Alarm Returning the unit to the factory default state Initialize Setting items stored on the unitSetup ALL SetupReturning the unit to the factory default state Setting items stored on the unitInitialize ALL AW‑RP120 Registering camera numbers to CAM OUT1 to CAM OUT10 CAM OUT1Setup Software Installing the softwareRegistering the unit in Setup Software Enter the IP addresses in the IP address boxesSettings for connecting with the remote cameras and switcher Displaying the Setting tab Executing auto IP setting Acquiring the connection settingsChanging the connection destination IP addresses Initializing the IP addressesSetting user authentication Enter the same password as above in the Retype password boxClicking Refresh clears the user name and password Campinp Mode Operations of AW-HE2Campinp CTL Campinp POSTable of setting items dedicated dials and buttons Dial/button Setting item Remote cameraTable of setting items menus VideoFilm Table of setting items menus SW Setup SW CTL When starting up and switching camera groups Preset memoryMessages Operation lockIP connection settings Memory cardMessages Index Xx MenuIndex プロフェッショナルAVビジネスユニット