Bosch Appliances MIC400AL MIC-12PSU Power Supply Unit, 12 or 24 Volt vehicle supply

Page 18

MIC400 Series Camera Installation and Operation Manual

MIC-12PSU Power Supply Unit

The power supply provides power for a single MIC400 non-ir camera unit from a 9v DC to 29v DC source for installation of the MIC400 camera on vehicle mounted applications.

Dimensions

Power supply enclosure – 225mm (W) x 70mm (H) x 195mm (D)

This is connected as per the MIC-240PSU as shown previously with the exception of the following changes:-

WARNING: Electrical Danger: Ensure all power is disconnected before opening or working upon any Power Supply Unit. Installation must be carried out by suitably qualified persons & all local safety regulations should be followed.

For vehicle mounted installation a specialist installer is recommended.

CAUTION: It is extremely important to observe the correct polarity, failure to do so will result in the destruction of the DC-DC power supply.

CAUTION: This power supply was designed for negative earthed vehicles only it is not suitable for use with positive earth vehicles.

12 or 24 Volt vehicle supply

This should be fed in to connection HD1 nominally marked as mains input, connections should be as follows:-

Table G – Power Input wiring connections for MIC-12PSU


	Positive	HD1-1

	Negative	HD1-2

	Earth and Negative	HD1-3

EN 18

The rating of fuse FS2 should be changed to a 2A quickblow as opposed to the rating shown on the PCB.

Power Supply Layout and Connections

HD1 – Power Input Connector (screw terminal)

HD2 - Keyboard power connector (demo purposes only, not normally fitted) HD3 - Composite cable header (Connections to camera head, screw terminal) HD4 - Telemetry header (Molex Connection)

HD5 - Telemetry header (Screw terminal) HD6 - Tamper Switch header (Screw terminal)

HD7 – Washer Pump Drive header (Screw terminal) CN1 - Video out connection header (BNC)

CN2 - Add on card header (plug in)

Figure B – MIC12-PSU Layout

For 12V vehicle installations the composite cable wiring is identical to that shown earlier in this manual on Table C

Bosch Security Systems

Issue 1

Image 18

Contents MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-24PSU MIC-240PSUMIC-115PSU MIC-12PSUMIC-BP3 MIC-WKTMIC-ALM MIC-BP4Packaging Contents UnpackingInstallation Environment Key to MIC-PMB drawing Associated Equipment & Typical Installations Installation InstructionsUnderwater Installation Earthing of the MIC400 cameraLightning Protection Table a MIC Composite Cable Pin table NON-IR Power Supply UnitsElectrical Connections MIC-240PSU, MIC-24PSU and MIC-115 PSUPower Supply Layout and Connections Table B Power Connection to Header HD1PCB Earth Link HD3 HD4HD5 Bi-phase cards etc Rating for PrimaryMIC-12PSU Power Supply Unit Table G Power Input wiring connections for MIC-12PSU12 or 24 Volt vehicle supply MIC400PA Optional Cards and Kits for Non-IR MIC400 CamerasCommissioning MIC400PA and MIC400’s with heaters fitted Heater OptionBosch Security Systems Issue MIC400IR Power Supply Units Setting the Power Supply Link OptionsMIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU Figure D MIC-IR-240PSU Layout Table I Fuse Ratings for MIC-IR-240PSU Function TypeTerminal Box ID Marking SignalTable K -IR Lamp Connections HD6 Table L -Washer Pump Connection HD7MIC-IR-12PSU Figure E MIC-IR-12PSU Schematic Table M Fuse ratings for MIC-IR-12PSU Function Type RatingInstallation Instructions Table N Connecting the Greenwich Adaptor Connecting the MIC400 to the PCConnecting the Greenwich Adaptor Adaptor ConnectionsSetting Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorDIP Switch Table O K2-ADE Adaptor connectionsTable Q MIC-USB485CVTR Connection Table and Diagram MIC Power Supply Converter Output Telemetry HeaderCommunication Mode MIC-USB485CVTR and Universal Camset Software Installation Commissioning the MIC400 through Universal CamsetStandard Controls Boot Messages MIC SettingsCamset Settings Iris Controls Reset CamsetManual Control Pan, Tilt and Zoom Controls Focus ControlsPreset Positions AuxiliariesTour Controls Soft Stops and Non Dwell ZonesPan Reverse MIC SetupsGeneral Settings Tilt ReverseAuto Home Controls Default Settings Other controlsMulti Alarm Settings Frame Integration Settings Privacy and CaptionsLens Recalibration and Frame Integration Privacy Controls Privacy Calibration CaptionsThermal Timers Advanced SettingsTemperature and Humidity Clear All StatisticsUpload Eeprom From File Eeprom CopierDownload Eeprom To File Remap Auxiliary Pelco OnlyPOT Test Menu Controls Panasonic OnlyMatrix Controls Pot Test Controls Pot Test ResultsSend Direct Command CommsMIC Comms Communications TestingAlarms Cam CommsSend Preset to MIC SonySet Preset NumberGet Preset from MIC Sony SetSave Table from MIC to File Execute this PresetLoad Table from File to MIC Clear TableTable R Sonyset Commands MIC Programmer Bosch Security Systems Issue Operational AlarmsCamera Module Communication & ProtocolsEnvironmental AccessoriesPhysical ElectricalMIC400PA Twin SpeakersMIC400UL and MIC400UT MIC400S MIC400IR IR IlluminatorsDimension Drawings Asia-Pacific Contact AmericasEurope, Middle East, Africa Bosch Security Systems IncAppendix a Protocol Preset codes Preset CodesPelco Bosch Security Systems Special Setup Presets VisionBosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2