Bosch Appliances MIC400AL Camera Module, Operational, Communication & Protocols, Connectivity

Page 55

MIC400 Series Camera Installation and Operation Manual

CHAPTER 5 Technical Specifications

MIC400AL

CAMERA MODULE
Image sensor	1/4" EXview CCD
Picture elements	380K NTSC / 440K PAL (WIDE)
Horizontal resolution	470TVL NTSC / 460TVL PAL (WIDE)
Filter	Automatic mechanical IR cut filter
Focus system	Auto or manual Iris
Synchronisation	Internal / External (V-Lock)
Recommended illumination	100 to 100,000 lx
Signal/Noise ratio	50dB or more
Back Light Compensation (BLC) On/Off
White balance	Automatic
Automatic Gain Control (AGC)	-3 to -28 dB, 2dB steps
Aperture control	16 Steps
18x optical zoom module
Lens	F=4.1mm (WIDE) to 73.8mm (TELE), F1.4 to
	F3.0
Zoom	18x optical (12x digital)
Angle of view	48º (WIDE end) to 2.8º (TELE end)
Minimum illumination	0.7 lux (F1.4, 1/60s NTSC, 1/50s PAL), 0.11 lux
	(F1.4, 1/4s NTSC, 1/3s PAL), 0.01 lux or less
	(F1.4, 1/4s NTSC, 1/3s PAL, ICR ON)
Shutter speed	1/1 to 1/10,000s (22 steps) NTSC, PAL
36x optical zoom module
Lens	F=3.4mm (WIDE) to 122.4mm (TELE), F1.6 to
	F4.5
Zoom	36x optical (12x digital)
Angle of view	57.8º (WIDE end) to 1.7º (TELE end)
Minimum illumination	1.4 lux (1/60s NTSC, 1/50s PAL), 0.1 lux (1/4s
	NTSC, 1/3s PAL), 0.01 lux or less (1/4s NTSC,
	1/3s PAL, ICR ON)
Shutter speed	1/4 to 1/10,000s (20 steps) NTSC, 1/3 to
	1/10,000s (20 steps) PAL

	EN 55
OPERATIONAL*
Auto flip	Yes
Manual flip	Yes
Dynamic privacy zones	3D privacy masking with infinite zones (using
	optional
	privacy card)
Presets	64 telemetry presets utilising resolver technology
	(using FV protocol, 10 camera set-up presets to
	allow ANPR, colour correction etc.)
Preset tours	Auto or manual with slow shutter integr
Preset tours	6 tours each with up to 32 presets
Sector titles	Yes (64 sectors) 20 characters per title
Preset titles	20 character caption for each of the 64 presets
Home position	Yes (preset 1 or tour)
COMMUNICATION & PROTOCOLS
Communication	RS485 / RS422
Control protocol	Refer to current supported protocol list
CONNECTIVITY
Video	Co-axial via composite cable
Telemetry	Twisted pair. Simplex, half and full duplex
	operation via composite cable
Power	Via composite cable
ALARMS
Alarm inputs	1 tamper input (additional inputs possible with
	optional alarm card in PSU)
Alarm communication	Tamper switch (ground connection)

MECHANICAL

Bosch Security Systems

Issue 1

Image 55

Contents MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-12PSU MIC-240PSUMIC-115PSU MIC-24PSUMIC-BP4 MIC-WKTMIC-ALM MIC-BP3Unpacking Packaging ContentsInstallation Environment Key to MIC-PMB drawing Installation Instructions Associated Equipment & Typical InstallationsEarthing of the MIC400 camera Underwater InstallationLightning Protection MIC-240PSU, MIC-24PSU and MIC-115 PSU NON-IR Power Supply UnitsElectrical Connections Table a MIC Composite Cable Pin tableTable B Power Connection to Header HD1 Power Supply Layout and ConnectionsPCB Earth Link HD4 HD3HD5 Rating for Primary Bi-phase cards etcTable G Power Input wiring connections for MIC-12PSU MIC-12PSU Power Supply Unit12 or 24 Volt vehicle supply Heater Option Optional Cards and Kits for Non-IR MIC400 CamerasCommissioning MIC400PA and MIC400’s with heaters fitted MIC400PABosch Security Systems Issue Setting the Power Supply Link Options MIC400IR Power Supply UnitsMIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU Table I Fuse Ratings for MIC-IR-240PSU Function Type Figure D MIC-IR-240PSU LayoutTable L -Washer Pump Connection HD7 SignalTable K -IR Lamp Connections HD6 Terminal Box ID MarkingMIC-IR-12PSU Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Figure E MIC-IR-12PSU SchematicInstallation Instructions Adaptor Connections Connecting the MIC400 to the PCConnecting the Greenwich Adaptor Table N Connecting the Greenwich AdaptorTable O K2-ADE Adaptor connections Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorDIP Switch SettingMIC Power Supply Converter Output Telemetry Header Table Q MIC-USB485CVTR Connection Table and DiagramCommunication Mode Commissioning the MIC400 through Universal Camset MIC-USB485CVTR and Universal Camset Software InstallationStandard Controls MIC Settings Boot MessagesCamset Settings Focus Controls Reset CamsetManual Control Pan, Tilt and Zoom Controls Iris ControlsAuxiliaries Preset PositionsSoft Stops and Non Dwell Zones Tour ControlsTilt Reverse MIC SetupsGeneral Settings Pan ReverseAuto Home Controls Other controls Default SettingsMulti Alarm Settings Privacy and Captions Frame Integration SettingsLens Recalibration and Frame Integration Privacy Controls Captions Privacy CalibrationThermal Clear All Statistics Advanced SettingsTemperature and Humidity TimersRemap Auxiliary Pelco Only Eeprom CopierDownload Eeprom To File Upload Eeprom From FileMenu Controls Panasonic Only POT TestMatrix Controls Pot Test Results Pot Test ControlsComms Send Direct CommandCam Comms Communications TestingAlarms MIC CommsSony Set SonySet Preset NumberGet Preset from MIC Send Preset to MICClear Table Execute this PresetLoad Table from File to MIC Save Table from MIC to FileTable R Sonyset Commands MIC Programmer Bosch Security Systems Issue Communication & Protocols AlarmsCamera Module OperationalElectrical AccessoriesPhysical EnvironmentalTwin Speakers MIC400PAMIC400UL and MIC400UT MIC400S IR Illuminators MIC400IRDimension Drawings Bosch Security Systems Inc Contact AmericasEurope, Middle East, Africa Asia-PacificPreset Codes Appendix a Protocol Preset codesPelco Bosch Security Systems Vision Special Setup PresetsBosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2