Bosch Appliances MIC400AL operation manual Rating for Primary, Bi-phase cards etc

Page 17

MIC400 Series Camera Installation and Operation Manual

Table F – Fuse Ratings for MIC-240PSU, MIC-24PSU and MIC-115PSU

EN 17

Fuse ident

FS 1

FS 2

FS 3

FS 5

Fuse function.

MIC400 protection

Primary protection.

Heater protection 1

Heater protection 2

Rating for 240v

primary

1.6A glass Anti

surge (T)

200mA ceramic

quick blow

1.6A glass Anti

surge (T)

1.6A glass Anti

surge (T)

Rating for 115v

primary

1.6A glass Anti

surge (T)

500mA ceramic

quick blow

1.6A glass Anti

surge (T)

1.6A glass Anti

surge (T)

7.	CN2 is for additional add on cards such as alarm inputs, video processors,
	Bi-phase cards etc.
8.	Telemetry connections are provided by headers HD3, HD4 and HD5 which
	respectively enable crimp or screw terminations for connecting the MIC400
	to the control room as per Table D.
9.	Connect the power to HD1 carefully observing the polarity and voltage as
	per Table B.
10.	When wiring is complete, apply power & check the all four (4) LED’s are lit.

Installation Instructions

WARNING: Electrical Danger: Ensure all power is disconnected before opening or working upon any Power Supply Unit.

Installation must be carried out by suitably qualified persons

&all local safety regulations should be followed.

1.Locate the mounting position of the MIC-PSU so that it cannot be interfered with either intentionally or accidentally, a lockable cabinet is recommended.

2.Securely fix the MIC-PSU using M4 stainless steel screws & washers; ensure the cable glands have sufficient room to allow for the cables to enter.

3.Feed all cabling through the appropriate sized gland holes.

4.Connect the composite cable to HD3 following the colour coding as shown in the Table C & printed on the PCB.

5.If a tamper switch relay is to be used, connect this at HD2.

6.Connect the Coaxial video cable to the CN1 header.

11.	Following Installation when power is applied the following LEDs will light to
	indicate:-
	LED1 – 15vAC power on to camera
	LED2 – 15vAC power on camera
	LED4 – Power on for optional heater/speaker
	LED5 – Power on for optional heater/speaker
12.	Re-attach the enclosure lid & screw down until tight.
13.	For installation of the MIC-WKT-KIT, MIC-ALM or MIC-BP-4 Bi-phase card
	please refer to their respective manuals.

Bosch Security Systems

Issue 1

Image 17

Contents MIC400 PTZ Camera Series MIC400 PTZ Camera Series Introduction Safety Precautions Important Safety Instructions Reference MIC-115PSU MIC-240PSUMIC-24PSU MIC-12PSUMIC-ALM MIC-WKTMIC-BP3 MIC-BP4Unpacking Packaging ContentsInstallation Environment Key to MIC-PMB drawing Installation Instructions Associated Equipment & Typical InstallationsLightning Protection Underwater InstallationEarthing of the MIC400 camera Electrical Connections NON-IR Power Supply UnitsTable a MIC Composite Cable Pin table MIC-240PSU, MIC-24PSU and MIC-115 PSUPCB Earth Link Power Supply Layout and ConnectionsTable B Power Connection to Header HD1 HD5 HD3HD4 Rating for Primary Bi-phase cards etc12 or 24 Volt vehicle supply MIC-12PSU Power Supply UnitTable G Power Input wiring connections for MIC-12PSU Commissioning MIC400PA and MIC400’s with heaters fitted Optional Cards and Kits for Non-IR MIC400 CamerasMIC400PA Heater OptionBosch Security Systems Issue MIC-IR-240PSU, MIC-IR-115PSU, MIC-IR-24PSU and MIC-IR-12PSU MIC400IR Power Supply UnitsSetting the Power Supply Link Options Table I Fuse Ratings for MIC-IR-240PSU Function Type Figure D MIC-IR-240PSU LayoutTable K -IR Lamp Connections HD6 SignalTerminal Box ID Marking Table L -Washer Pump Connection HD7MIC-IR-12PSU Table M Fuse ratings for MIC-IR-12PSU Function Type Rating Figure E MIC-IR-12PSU SchematicInstallation Instructions Connecting the Greenwich Adaptor Connecting the MIC400 to the PCTable N Connecting the Greenwich Adaptor Adaptor ConnectionsDIP Switch Connecting the KK systems K2-ADE RS232 to RS485/422 AdaptorSetting Table O K2-ADE Adaptor connectionsCommunication Mode Table Q MIC-USB485CVTR Connection Table and DiagramMIC Power Supply Converter Output Telemetry Header Standard Controls MIC-USB485CVTR and Universal Camset Software InstallationCommissioning the MIC400 through Universal Camset MIC Settings Boot MessagesCamset Settings Manual Control Pan, Tilt and Zoom Controls Reset CamsetIris Controls Focus ControlsAuxiliaries Preset PositionsSoft Stops and Non Dwell Zones Tour ControlsGeneral Settings MIC SetupsPan Reverse Tilt ReverseAuto Home Controls Other controls Default SettingsMulti Alarm Settings Lens Recalibration and Frame Integration Frame Integration SettingsPrivacy and Captions Privacy Controls Captions Privacy CalibrationThermal Temperature and Humidity Advanced SettingsTimers Clear All StatisticsDownload Eeprom To File Eeprom CopierUpload Eeprom From File Remap Auxiliary Pelco OnlyMatrix Controls POT TestMenu Controls Panasonic Only Pot Test Results Pot Test ControlsComms Send Direct CommandAlarms Communications TestingMIC Comms Cam CommsGet Preset from MIC SonySet Preset NumberSend Preset to MIC Sony SetLoad Table from File to MIC Execute this PresetSave Table from MIC to File Clear TableTable R Sonyset Commands MIC Programmer Bosch Security Systems Issue Camera Module AlarmsOperational Communication & ProtocolsPhysical AccessoriesEnvironmental ElectricalTwin Speakers MIC400PAMIC400UL and MIC400UT MIC400S IR Illuminators MIC400IRDimension Drawings Europe, Middle East, Africa Contact AmericasAsia-Pacific Bosch Security Systems IncPelco Appendix a Protocol Preset codesPreset Codes Bosch Security Systems Vision Special Setup PresetsBosch Security Systems Issue American Dynamics Kalatel Impossible to reach Molynx Panasonic Privacypresetend Multialarmpreset Bosch Forward Vision VCL Pantiltscaleonpreset Vicon PRIVACYSETUPBYTE2